Hitachi Projector CP-WX5500 User Manual

91
OPTION menu
ItemDescription
SERVICE
(continued)
COMMUNICATION (continued)
SERIAL SETTINGS
Select the serial communication condition for the 
CONTROL  port.
BAUD RATE 4800bps  ó 9600bps 
ó 19200bps 
ó 38400bps
      
  PARITY
NONE  ó ODD 
ó EVEN
    
• The BAUD RATE is fixed to 19200bps and PARITY 
is fixed NONE when the COMMUNICATION TYPE 
is set to OFF
 ( 90
).
TRANSMISSION METHOD
Select the transmission method for communication by 
the NETWORK BRIDGE from the  CONTROL port.
HALF-DUPLEX 
ó...

92
OPTION menu
ItemDescription
SERVICE
(continued)
COMMUNICATION (continued)
RESPONSE LIMIT TIME
Select the time period to wait for receiving 
response data from other device communicating by 
the NETWORK BRIDGE and the HALF-DUPLEX 
through the  CONTROL port.
OFF  ó 1s 
ó 2s 
ó 3s
    
OFF : Select this mode if it is not required to check 
the responses from the device that the projector 
sends data to. In this mode, the projector can 
send out data from the computer continuously.
1s /2s /3s: Select the...

93
OPTION menu
ItemDescription
SERVICE
(continued) CONTROL 
TERMINAL * WIRED NETWORK
Selects whether to use 
LAN or HDBaseT  port.
      LAN  ó HDBaseT
RS-232C
Selects whether to use  CONTROL or HDBaseT  
port.
      CONTROL  ó HDBaseT
HDMI OUT 
RESOLUTION Selects the device to refer to the resolution 
information of HDMI output.
      
EXTERNAL DEVICE
 ⇔ PROJECTOR
・ When EXTERNAL DEVICE is selected, the 
resolution of the signal input to the projector and 
signal output from the projector may be...

94
OPTION menu
ItemDescription
SERVICE
(continued) INFORMATION
Selecting this item displays a dialog titled “INPUT_INFORMATION”. 
It shows the information about the current input.
• The “FRAME LOCK” message on the dialog means the frame lock 
function is working. 
• This item cannot be selected for no signal and sync out.
• When the MY TEXT DISPLAY is set to ON, the MY TEXT is 
displayed together with the input information in the 
 
INPUT_INFORMATION box (
 101
).
FACTORY RESET
Selecting OK using the ►...

95
NETWORK menu
See the Network Guide for details of NETWORK operation.
Remember that incorrect network settings on this projector may cause trouble on 
the network. Be sure to consult with your network administrator before connecting 
to an existing access point on your network.
NETWORK menu 

96
SECURITY menu
This projector is equipped with security functions.
From the SECURITY menu, items shown in the table 
below can be performed.
To use SECURITY menu: User registration is required 
before using the security functions.
Enter to the SECURITY menu
1.  Press the ► button. The ENTER PASSWORD box will be displayed.
2.   Use the ▲/▼/◄/► buttons to enter the registered password. The 
factory default password is as follows.
   CP-WU5500/CP-WU5505  : 2905   CP-WX5500/CP-WX5505  : 1205...

97
SECURITY menu
ItemDescription
MyScreen 
PASSWORD
The MyScreen PASSWORD function can be used to prohibit access to the 
MyScreen function and prevent the currently registered MyScreen image 
from being overwritten.
1 Turning on the MyScreen PASSWORD1-1   Use the ▲/▼ buttons on the SECURITY menu to 
select MyScreen PASSWORD and press the ► 
button to display the MyScreen PASSWORD on/
off menu.
1-2   Use the ▲/▼ buttons on the MyScreen 
PASSWORD on/off menu to select ON. 
The ENTER NEW PASSWORD box...

98
SECURITY menu
ItemDescription
PIN LOCK
PIN LOCK is a function which prevents the projector from being used unless 
a registered Code is input.
1 Turning on the PIN LOCK1-1   Use the ▲/▼ buttons on the SECURITY menu 
to select PIN LOCK and press the ► button or 
the  ENTER  button to display the PIN LOCK on/off 
menu.
1-2   Use the ▲/▼ buttons on the PIN LOCK on/
off menu to select ON and the Enter PIN 
Code box will be displayed. 
1-3   Input a 4 part PIN code using the ▲/▼/◄/►   
or  INPUT  button....

99
SECURITY menu
ItemDescription
TRANSITION  DETECTOR
If this function is set to ON and the vertical angle of 
the projector or the INSTALLATION setting is different 
from the previous recorded setting, the TRANSITION 
DETECTOR ON alarm will be displayed and the input 
signal will not be displayed.
• To display the signal again, set this function OFF.
• After about 5 minutes of displaying the TRANSITION DETECTOR ON 
alarm, the lamp will turn off.
1 Turning on the TRANSITION DETECTOR1-1   Use the ▲/▼...

100
SECURITY menu
ItemDescription
MY TEXT 
PASSWORD
The MY TEXT PASSWORD function can prevent the MY TEXT from being 
overwritten. When the password is set for the MY TEXT;
• The MY TEXT DISPLAY menu will be unavailable, which can prohibit 
changing the DISPLAY setting.
• The MY TEXT WRITING menu will be unavailable, which can prevent the 
MY TEXT from being overwritten.
1 Turning on the MY TEXT PASSWORD1-1   Use the ▲/▼ buttons on the SECURITY menu to 
select the MY TEXT PASSWORD and press the 
► button...