Hitachi Projector CP-WU8451 User Manual

21
  In a normal state  
The Status Monitor displays the state of the projector in 
three lines.
:  Displays the condition of the projector. 
While the lamp is on, the selected port is 
displayed.
Displayed conditions are as below;
STANDBY: The projector is in standby mode.
WARM UP: The projector is warming up.
SEARCHING: The projector is searching an input signal.
COOL DOWN:  The projector is cooling down.
:  Displays the condition of the detected input signal while the lamp 
is on. Otherwise, displays...

22
  In error state 
The Status Monitor displays a warning of an error with 
larger letters. Resolve the errors referring to the table 
of the sections Related messages
 (118 ~ 120) and 
Regarding the indicator lamps 
(121 d 123) when the 
warning is displayed. 
Displayed warnings are as below;
COVER: The lamp cover has not been properly fixed. 
Refer to the LAMP indicator blinking in the table 
(121).
FAN: The cooing fan is not operating. 
Refer to the TEMP indicator blinking in the table 
(122)....

23
Status Monitor  
When the projector is in a normal condition, 
or displays one of the warnings of AIR FLOW, 
COLD or FILTER errors, press the FUNCTION 
button on the control panel, press the ENTER 
button on the remote control for three seconds 
or press one of the MY BUTTON buttons if 
assigned as STATUS MONITOR. The backlight 
of the monitor turns on.
  To display the setup information including 
usage time
Use the ◄/► buttons to switch display. 
    
  
Usage time: The Status Monitor displays 
the...

24
AC240V35°C
7FILTERERRO
1PREVIOUS
  To display error history 
Press the ▲ button to display previous error 
log. If a warning has been displayed, the 
first previous error log is the present error 
currently occurring. The Status Monitor 
displays the log number, occurred error, the 
supplied voltage and peripheral temperature 
at that time. Press the ► button to display the 
usage time when each error occurred. 
Use the ▲/▼ buttons to switch the log. 
The display switches with the ◄/► 
buttons at each...

25
1.Make sure that the power cord is firmly 
and correctly connected to the projector 
and the outlet.
Tur ning on the power
2.Make sure that the POWER indicator is 
lighted in steady orange (
121). Then 
remove the lens cover.
3.Press STANDBY/ON button on the projector  
or the ON button on the remote control.
The projection lamp will light up and POWER indicator will begin blinking in 
green. When the power is completely on, the indicator will stop blinking and 
light in steady green (
121).
Power...

26
Operating
Operating
1.
Adjusting the volume
Use the VOL + / - buttons to adjust the volume. 
A dialog will appear on the screen to aid you in 
adjusting the volume. If you do not do anything, 
the dialog will automatically disappear after a few 
seconds.
• 
When  is selected for current picture input port, the volume 
adjustment is disabled. Please see AUDIO SOURCE item of AUDIO menu (
60).
• Even if the projector is in the standby mode, the volume is adjustable when 
both of the following conditions...

27
Operating
1.Press INPUT button on the projector. 
Each time you press the button, the projector 
switches its input port from the current port as 
below.
Selecting an input signal
1.Press COMPUTER 1, LAN, USB TYPE A / B, HDMI 1 / 2, DIGITAL, 
COMPONENT, S-VIDEO or VIDEO button on the remote control. 
The port corresponding to each button is selected as below.
Button Ports
COMPUTER 1 COMPUTER IN
LAN LAN
USB TYPE A USB TYPE A
USB TYPE B USB TYPE B
HDMI 1 HDMI 1
HDMI 2 HDMI 2
COMPONENT COMPONENT
S-VIDEO...

28
Operating
Selecting an aspect ratio
  For a computer signal
 NORMAL  4:3  16:9  16:10  NATIVE 
        
  For a video signal, s-video signal or component video signal
 4:3  16:9  16:10  14:9  NATIVE 
  
   For an input signal from the LAN, USB TYPE A or USB TYPE B ports, or 
if there is no signal 
16:10 (fixed)
1.Press ASPECT button on the remote control.   
Each time you press the button, the projector switches 
the mode for aspect ratio in turn. 
  For HDMI
TM and HDBaseTTM signals...

29
Operating
Adjusting the projector’s elevator
When the place to put the projector is slightly uneven 
to the left or right, use the elevator feet to place the 
projector horizontally.
Using the feet can also tilt the projector in order to 
project at a suitable angle to the screen, elevating the 
front side of the projector within 9 degrees.
This projector has 2 elevator feet and 2 elevator buttons. 
An elevator foot is adjustable while pushing the elevator 
button on the same side as it.
1. 
Holding...

30
Operating
The ZOOM or FOCUS dialog will appear when you 
press any of the buttons from ZOOM, ZOOM -, 
ZOOM +, FOCUS + and FOCUS -. 
1. Use the ZOOM + / - buttons on the remote 
control or ZOOM button and ◄/► cursor buttons 
on the projector to adjust the screen size.
2. Use the FOCUS + / - buttons to focus the picture.
Adjusting the lens 
Adjusting the zoom and focus
• The projector may ignore operation by 
other buttons while the lens is moving.NOTE
Press the LENS SHIFT button. The LENS SHIFT 
dialog...