Hitachi Projector CP-WU5500 User Manual

31
1.Press the STANDBY/ON button on the projector or the remote control.  
The message “Power off?” will appear on the screen for about 5 seconds.
Turning off  the power
2.Press the STANDBY/ON button again while the message appears.   
The projector lamp will go off, and the POWER indicator will begin blinking 
in orange. Then the POWER indicator will stop blinking and light in steady 
orange when the lamp cooling is complete (
11 2 ).
3.Attach the lens cover, after the  POWER indicator turns to steady...

32
Operating
Operating
Adjusting the volume
Use the VOLUME +  / - buttons to adjust the volume. 
A dialog will appear on the screen to aid you in   
adjusting the volume. If you do not do anything, the 
dialog will automatically disappear after a few seconds.
• 
When  is selected for current picture input port, the volume 
adjustment is disabled. Please see AUDIO SOURCE item of AUDIO menu (
 75).
• Even if the projector is in the standby mode, the volume is adjustable when 
both of the following...

33
Operating
Press INPUT button on the projector or the remote 
control. Select a desirable input referring to the 
displayed input list.
Selecting an input signal
           LAN   COMPUTER IN     HDMI 1 / MHL
         VIDEO                                      
         HDBaseT*                             HDMI 2
• If you have set SKIP to some ports from SOURCE SKIP in the 
OPTION menu, the input from the ports cannot be selected (
 82).
• While ON is selected for AUTO SEARCH item in OPTION menu,...

34
Operating
ASPECT
BLANKESCMENU
RESET
AUTOPAGEDOWN
ONOFFFREEZE
UP
ENTER
FOCUS- +ZOOM- +
INPUT
INTERACTIVE
MYBUTTON1
2PbyPMAGNIFYVOLUME-
+GEOMETRY PICTURE MUTE
NETWORK
OSD MSG
Selecting an aspect ratio
Press ASPECT button on the remote control.   
Each time you press the button, the projector 
switches the mode for aspect ratio in turn. 
• ASPECT button does not work when no proper signal is input.
• NORMAL mode keeps the original aspect ratio setting. NOTE
  
For a computer signal  
CP-X5550, CP-X5555:...

35
Operating
Adjusting the projector’s elevator
When the place to put the projector is slightly 
uneven to the left or right, use the elevator feet to 
place the projector horizontally. Using the feet can 
also tilt the projector in order to project at a 
suitable angle to the screen, elevating the front 
side of the projector within 11 degrees.
This projector has 2 elevator feet and 2 elevator buttons. An elevator foot is 
adjustable while pushing the elevator button on the same side as it.
1. 
Holding...

36
Operating
Adjusting the lens shift
1.  
Turn the  VERTICAL  adjuster fully counter 
clockwise. Then turn it clockwise and 
adjust the vertical lens position upward.
2.    Turn the  HORIZONTAL  adjuster clockwise 
or counter clockwise to adjust the 
horizontal lens position.
CAUTION   ►Operate the lens adjusters gently as the lens may malfunction
when subjected to shocks. It may need more strength to turn the adjusters near
the adjustment limits. Be careful not to apply too much strength. If the lens...

37
Operating
Press AUTO button on the remote control.  
Pressing this button performs the following.
Using the automatic adjustment feature
  For a computer signal  
The vertical position, the horizontal position and the   
horizontal phase will be automatically adjusted.   
Make sure that the application window is set to its   
maximum size prior to attempting to use this feature. A dark picture may still be 
incorrectly adjusted. Use a bright picture when adjusting.
   For a video signal  
The video...

38
Operating
KEYSTONE:   allows you to adjust the vertical and 
horizontal keystone.
PERFECT FIT :   
allows you to adjust each of the screen 
corners and sides to correct the 
distortion.
WARPING:   allows you to project an image on several 
types of screen.
• The menu or dialog will automatically disappear after several seconds 
of inactivity. Press the GEOMETRY button again, or point the cursor at EXIT in 
the dialog and press the ►or  ENTER button to end the operation and close the 
menu or dialog....

39
Operating
   
PERFECT FIT: 
When PERFECT FIT is pointed at, pressing the 
► or  ENTER  button displays the PERFECT FIT 
dialog. This projector is equipped with a test pattern for 
PERFECT FIT. Select PATTERN with the 
▲/▼ 
buttons, then press the 
◄/► buttons to switch on 
and off.
1.  Select SETUP with the ▲/▼ buttons and   
  press the ► or  ENTER button.
2.
 Select one of the corners or sides to be adjusted  
 
with the ▲/▼/◄/► buttons and press the  
ENTER  or 
 button.
3. Adjust the selected...

40
Operating
Correcting the distortion (continued)
4. This projector is equipped with a memory feature for PERFECT FIT adjustment. Up to 3 sets of adjustments can be stored.
●   SAVE:   
To store the current PERFECT FIT adjustment, select one of the "SAVE" 
options numbered 1 to 3 (number of the memory) with the ▲/▼ buttons and 
press the ►,  ENTER or 
 button.  
Remember that the current data being stored of a memory will be lost by 
saving new data into the memory.
●   LOAD:   
To recall stored...