Hitachi Projector CP-WU13K User Manual

21 Installation of the Projector
Connecting the projector to other devices
HDMI / DVI connection
Signals from image source offer the best projection image quality when sent through HDMI. 
Therefore, try to use input devices with HDMI output as the source of image.
  
COMPONENT 2SDI / HDSDI / 3G
COMPONENT 1
YPbPr 10/100 BASE-T RS-232 WIRED REMOTE12V TRIGGERIII
350mASYNC IN SYNC OUT
IN OUT G/Y B/Pb R/Pr H VVGA
HDMI   HDMI STEREO DVI
HDMI/DVI input source
(BD/HD-DVD/DVD player, HD set-top-box, 
gaming...

22Installation of the Projector
RGB connection
Connect your PC or other devices with RGB output to the RGB input connectors on the projector to be 
used as the source of image input.
COMPONENT 2SDI / HDSDI / 3G
COMPONENT 1
YPbPr 0/100 BASE-T RS-232 WIRED REMOTE12V TRIGGERIII
350mA
IN OUT G/Y B/Pb R/Pr H VVGA
HDMI   HDMI 

Desk Top or Notebook
COMPONENT 2SDI / 3G
COMPONENT 1
YPbPr-T RS-232 WIRED REMOTE12V TRIGGERIII
350mASYNC IN SYNC OUT
OUT G/Y B/Pb R/Pr H VVGA
HDMI   HDMI STEREO DVI
G/Y B/Pb R/Pr H...

23 Installation of the Projector
COMPONENT connection
J	



24Installation of the Projector
3D mode
There are few ways to go to the 3D mode
#
OSD menu: Go to Main Menu “Input > Input Selection”, and select STEREO DVI
#
Remote control: Press hot key “5” to go to STEREO DVI directly
#
Network Webpage: Go to “Source/general” > “Source” and select STEREO DVI
#
RS232 Commands : Use “ Input Selection” to select STEREO DVI
When this function is blanking. The 3D Mode is not available
2D mode
Please note that OSD menu is not available in 3D mode. The ways to switch back...

25 Installation of the Projector
Adjusting screen orientation

26Installation of the Projector
Rear projection - desktop installation 
Press MENU  ALIGNMENT 

27 REMOTE CONTROL
Remote control
 
2
32
41
5
INPUT
ASPECT
RATIO
AUTO IMAGE
PAUSE TEXT MENU
SHARPN
PHASE COLOR TINT
ADDRESS SWAP PIP
1
3
4            
6
72
5
1.  ON 
This button is used to turn on the projector.
2. 
 OFF 
This button is used to turn off the projector.
3. 
12345 
These buttons on the remote control are the hotkeys 
for different image source. By factory default, these 
are:  
1 = HDMI 1 
2 = RGB D-15 
3 = COMPONENT2 
4 = COMPONENT1 
5 = Stereo DVI
Note: These buttons may not work at PIP...

28REMOTE CONTROL
 AUTO  IMAGE   
  This button is used to  Resync the 
  image; when the image signal 
  becomes unstable or image  
  quality deteriorates simply press 
  this button and the  projector will 
  automatically adjust the screen 
  dimension, phase, timing and so 
  forth.(The adjustments also apply 
  to PIP input).  
 CONTRAST  
  Adjust the level of white in the  
  image to increase or decrease 
 image contrast.  
 BRIGHTNESS  
  Adjust the level of black in the  
  image to increase or...

29 OSD Menu description
OSD Menu Tree 
INPUTInput SelectionHDMI1 
HDMI2 
RGB D -15 
YUV1 
RGBH V/ Y U V2 
SDI/HDSDI/3G 
STER EO DVI


	
Auto 
YUV HD 
YUV STD 
RGB -PC 
RGB -Video
Input LockingAuto 
48Hz, 50Hz, 60Hz
Auto Power OffOn 
Off
Auto Power ONOn 
Off
No SignalLogo 
Blue 
Black 
White
Auto Image AdjustOff, Auto 
Always
IMAGEContrast 0~200
Brightness 0~200
Sharpness 0~200
Noise Reduction 0 ~200
Color Temperature3200K, 5400K, 6500K, 
9300K, Native
Input BalanceBlack Balance Offset 
Red...

30OSD Menu description
ALIGNMENTRear ProjectionOn 
Off
Ceiling ModeOn 
Off
Lens ControlZoom/Focus 
Shift V 
Shift H
Dynamic ContrastOn  
Off 
Gamma1.8      2.0     2.2 
2.35     2.5    Dicom  sim
Internal PatternsO n (1~12 Pat t e r n) 
Off (0 off )
Color SpaceNative,  EBU,  SMPTE 
Custom
Lens To  
MidpositionExecute
Wa r pHorizontal Keystone 
Vertical Keystone 
Rotation 
Pincushion / Bar rel 
Top Left Cor ner 
Top Right Cor ner 
Bottom Left Cor ner 
Bottom Right Cor ner
BlankingTop,     Bottom 
Left,...