Hitachi Projector CP-BW301Wn User Manual

							61
OPTION menu
ItemDescription
MY BUTTON ( Continued )• 
 
ACTIVE IRIS: Changes the active iris mode.
• PICTURE MODE: Changes the PICTURE MODE (
 33
).
•  FILTER RESET: Displays the filter time reset confirmation dialogue  ( 47
).
•   RESOLUTION: Turns on/off the RESOLUTION dialog ( 43
).
•   MIC VOLUME: Turns  on/off the MIC VOLUME dialog ( 51
).
•   ECO MODE: Changes the ECO MODE ( 46
).
•   SAVER MODE: Turns on/off the SAVER MODE ( 46
).
SCHEDULE
■ How to setup the item
1. Use the ▲/▼/◄/► cursor buttons to select or adjust.
2 Select OK to finish the settings.
NOTE
Item Description
DATE AND TIME Set the DATE(Year/Month/Date) and Time(24-
hour scale).
SPECIFIC DATE Set specific date from 1 to 10.
PROGRAM EDIT The TIME and EVENT for Program 1 to 16 
can be editted.
■ How to activate(DATE AND TIME / SPECIFIC DATE)
Place a check mark in the box.
      1/2 page (Set the DATE(Year/Month/Date) and Time(24-hour scale).)
                •   Please refer to the actual on-screen display(OSD) 
for appropriate operation.
Check mark 
in the boxDate and first setup 
info could be seen 
with the check mark.
(continued on next page) 
						

							62
OPTION menu
ItemDescription
SCHEDULE
( Continued )               2/2 page (Set specific date from 1 to 10.)
■ PROGRAM EDIT
The TIME and EVENT for Program 1 to 16 can be editted.
• RETURN
Select this to go back 
to the top menu of the 
SCHEDULE.
• SELECT
Select from PROGRAM-01 
to 16 to edit. 
Each PROGRAM can be 
setup up to 20 settings
• COPY TO
The selected program (with the settings of TIME and EVENT) 
can be copied to other program.
• APPLY
Select this to apply and save all adjustments and settings.
(continued on next page)
Check mark 
in the box
Date and 
first setup 
info could be 
seen with the 
check mark.
Press the ▼ cursor button to move from 1/2 page to 2/2 page with
the state of selecting "SATURDAY". 
						

							63
OPTION menu
ItemDescription
SCHEDULE
( Continued )
■ How to edit the selected PROGRAM
1.  Select from 1 to 20 events.  
Use the ▲/▼ cursor buttons to select.  
Press ► cursor button to set the TIME and EVENT.
2. Use the ◄/► cursor 
buttons to select.
3. Use the ◄/► cursor 
buttons to adjust.
EVENT can be selected as listed below. ◦ POWER − ON, STANDBY
◦ INPUT SOURCE − "input source"channel
◦ MY IMAGE − IMAGE-1 to 4, IMAGE OFF
◦ MESSENGER − TEXT-1 to 12, TEXT OFF
◦ 
ECO MODE − OFF, ECO-1, ECO-2, INTELLIGENT ECO,              
SAVER  
◦ BLANK − ON, OFF
◦ SLIDESHOW - START, STOP
4. Press ► cursor button to finish the settings. 
5.   Select APPLY to save the settings.
NOTE
(continued on next page)                 •
 Please refer to the actual on-screen display(OSD)  
for appropriate operation. 
						

							64
OPTION menu
ItemDescription
SERVICE Selecting this item displays the SERVICE 
menu.
Select an item using the ▲/▼ buttons, and 
press the ► button or the 
ENTER button 
on the remote control to execute the item.
ALTITUDE
Using the ▲/▼ buttons switches the rotation speed of the cooling 
fans. If the projector is used at an altitude of about 1600 m or higher, 
select HIGH. Otherwise, select NORMAL. Note that the projector is 
noisier when the HIGH is selected.
HIGH  ó NORMAL
AUTO ADJUST
Using the ▲/▼ buttons to select one of the mode. When the 
DISABLE is selected, the automatic adjustment feature is disabled.
FINE  ó FAST 
ó DISABLE
   
FINE: Finer tuning including H.SIZE adjustment.
FAST :  Faster tuning, setting H.SIZE to prearranged data for the 
input signal.
• Depending on conditions, such as input image, signal cable to 
the projector, environment around the projector, etc., the automatic 
adjustment may not work correctly.  In such a case, please 
choose DISABLE to disable the automatic adjustment, and make 
adjustment manually.
GHOST
Adjust the settings using the ▲/▼ buttons to eliminate ghosting.
(continued on next page) 
						

							65
OPTION menu
ItemDescription
SERVICE
(continued) KEY LOCK
(1)  
Use the ▲/▼ buttons to select CONTROL PANEL or REMOTE 
CONTROL.
(2) Use the ◄/► buttons to turn the key lock function on/off.
When ON is selected, all buttons on the projector or remote control 
except the  STANDBY/ON  button are locked.
• Please use this function to prevent tampering or accidental 
operation. 
• It is not possible to set both CONTROL PANEL and REMOTE 
CONTROL to ON.
(continued on next page) 
						

							66
OPTION menu
ItemDescription
SERVICE
(continued) REMOTE FREQ.
(1)   Use the ▲/▼ button to change the projector's remote sensor 
frequency setting  (
18
).
1:NORMAL  ó 2:HIGH
(2)   Use the ◄/► button to change the 
projector's remote sensor on or off.
ON  ó OFF
The factory default setting is for both 1:NORMAL and 2:HIGH to be 
on. If the remote control does not function correctly, disable either of 
them.
It's not possible to disable both options at the same time.
COMMUNICATION
Selecting this item displays COMMUNICATION 
menu. 
In this menu, you can configure the serial 
communication settings of the projector using the 
CONTROL  port.
• Select an item using the cursor buttons ▲/▼. 
Then pressing the ► button opens the submenu 
for the setting item you selected. Or, pressing 
the ◄ button instead of the ► button makes the 
menu back to the previous one without changing 
the setup. Each submenu can be operated as 
described above.
• When COMMUNICATION TYPE (
 67
) is set to 
OFF, the other items in COMMUNICATION menu 
are invalid. 
• For the function of serial communication, refer to  
the User's Manual - Network Guide .
(continued on next page) 
						

							67
OPTION menu
ItemDescription
SERVICE
(continued)
COMMUNICATION (continued)
COMMUNICATION TYPE
Select the communication type for transmission via 
the  CONTROL  port.
NETWORK BRIDGE: 
Select this type, if it is required 
to control an external device as a network terminal, 
via this projector from the computer. 
The  CONTROL  port doesn't accept RS-232C  
commands (
 Network Bridge Function
 in the 
User’s Manual - Network Guide)
OFF : Select this mode to receive RS-232C 
commands using the  CONTROL port. 
• 
OFF is selected as the default setting. 
• When you select the NETWORK BRIDGE, check 
the item, TRANSMISSTION METHOD  (
below
).
SERIAL SETTINGS
Select the serial communication condition for the 
CONTROL  port.
BAUD RATE 4800bps  ó 9600bps 
ó 19200bps 
ó 38400bps
      
  PARITY
NONE  ó ODD 
ó EVEN
    
• The BAUD RATE is fixed to 19200bps and PARITY 
is fixed NONE when the COMMUNICATION TYPE 
is set to OFF
 ( above
).
TRANSMISSION METHOD
Select the transmission method for communication by 
the NETWORK BRIDGE from the  CONTROL port.
HALF-DUPLEX 
ó FULL-DUPLEX
HALF-DUPLEX : This method lets the projector 
make two way communication, but only one 
direction, either transmitting or receiving data, is 
allowed at a time.
FULL-DUPLEX : This method lets the projector 
make two way communication, transmitting and 
receiving data at the same time.
• HALF-DUPLEX is selected as the default setting.
• If you select HALF-DUPLEX, check the setting of 
the item RESPONSE LIMIT TIME  (
68
).
(continued on next page) 
						

							68
OPTION menu
ItemDescription
SERVICE
(continued)
COMMUNICATION (continued)
RESPONSE LIMIT TIME
Select the time period to wait for receiving 
response data from other device communicating by 
the NETWORK BRIDGE and the HALF-DUPLEX 
through the  CONTROL port.
OFF  ó 1s 
ó 2s 
ó 3s
    
OFF : Select this mode if it is not required to check 
the responses from the device that the projector 
sends data to. In this mode, the projector can 
send out data from the computer continuously.
1s /2s /3s: Select the time period to keep the  projector waiting for response from the device 
that the projector sends data to. While waiting the 
response, the projector does not send out any 
data from the  CONTROL port.
• This menu is available only when the NETWORK 
BRIDGE is selected for the COMMUNICATION 
TYPE and the HALF-DUPLEX is selected for the 
TRANSMISSION METHOD  (
67
).
• OFF is selected as the default setting.
CLONING
The setttings of the projector can be coppied via USB 
memory.
SAVE:  Saves each settings of the projector to USB 
memory.
LOAD: 
Loads each settings of the projector from 
USB memory. Message will be displayed 
after loading, and power will turn off after five 
min. or by pressing ► button. (A message is 
displayed for a few seconds if loading fails.)
After saving / loading, you can remove the USB 
storage device.
(continued on next page) 
						

							69
OPTION menu
ItemDescription
SERVICE
(continued)
CLONING(continued)
The following items are exempted.
SETUP: LAMP TIME, FILTER TIME
OPTION: SERVICE(GHOST)
NETWORK: WIRELESS AND WIRED SETUP
(IP ADDRESS, SUBNET MASK, 
DEFAULT GATEWAY, DATE AND 
TIME), MY IMAGE, PRESENTATION
SECURITY: MY TEXT DISPLAY
• Operation is not available if SECURITY_
CLONNING LOCK is turned ON.
• The Screen_MyScreen can only be loaded.
CLONING load function on STANDBY MODE
• While the projector is in STANDBY MODE, push 
the INPUT button of control panel together with  ► 
button, and then press ▲ button to start operating 
the CLONING load function.
• During loading process, the three indicators of 
control panel (POWER (orange), TEMP, LAMP) 
will remain on.
•    After the loading process, the three indicators 
(POWER (orange), TEMP, LAMP) will turn off. 
Then, you can remove the USB storage device.
•   If the loading fails, the three indicators (POWER 
(orange), TEMP, LAMP) will blink at the same 
time.
• CLONING is invalid with the following conditions.
- CLONING LOCK is turned ON. 
    With this condition, the three indicators (POWER 
(orange), TEMP, LAMP) will blink at approximately 
three seconds intervals.
- If the STANDBY MODE is set to SAVING.
-   If there is no USB memory inserted into USB 
TYPE A port.
-   If PIN LOCK is not being released.
- If a system error occurs.
• Please operate one of the following after loading.
-   Press INPUT button and 
◄ button of the control 
panel  at the same time.
- Wait at least five min. after loading. 
-   Restart the projector after re-plugging the AC 
cable.
(continued on next page) 
						

							70
OPTION menu
ItemDescription
SERVICE
(continued)
CLONING(continued)
Load MyScreen data
•   Please save the image data as "pj_logo.bmp" or 
"pj_logo.gif" into USB memory.
•   Please note that the only compatible formats are 
as follows.
-File format Windows BMP    bit/pixel: 4/8/16/24/32bit
Compression format : 
Without compression/RLE/GIF
-Image size: more than 36x36, less than 1280x800
•   If two kinds of file format are saved, "pj_logo.
bmp" will be registered into MyScreen data.
•   If MyScreen LOCK or MyScreen PASSWORD 
is turned ON, the data of MyScreen cannot be 
loaded.
Setting the data
•   Operating the SAVE function under CLONING 
will name the file as "pj_data.bin" into the USB 
memory. Please do not attempt to change the file 
name or the folder structure.
•   If a file with the same name already exists, it will 
be overwritten by operating the SAVE function.
Loading function
•   Please note that saved data from other model 
cannot be loaded.
•  
Please note that, if any of the following functions: 
MyScreen PASSWORD, PIN LOCK, MY TEXT 
PASSWORD under SECURITY menu or 
MyScreen Lock under SCREEN menu is ON, the 
respective saved data cannot be loaded.
  
(continued on next page)