Hitachi Projector CP-BW301Wn User Manual

							31
Operating
Using the menu function (continued)
3.To close the MENU, press the MENU button again or select EXIT and press 
the ◄ cursor button or ENTER button. Even if you do not do anything, the 
dialog will automatically disappear after about 30 seconds.
●  If you want to move the menu position, use the cursor buttons after pressing the 
POSITION  button.
●   Some functions cannot be performed when a certain input port is selected, or 
when a certain input signal is displayed.
●   When you want to reset the operation, press  RESET button on the remote 
control during the operation. Note that some items (ex. LANGUAGE, VOLUME) 
cannot be reset.
●   In the ADVANCED MENU, when you want to return to the previous display, 
press the ◄ cursor button or ESC button on the remote control.
Indication in OSD (On Screen Display)
The meanings of the general words on the OSD are as follows.
Indication Meaning
EXITSelecting this word finishes the OSD menu. It's the same as 
pressing the 
MENU button.
RETURN Selecting this word returns the menu to the previous menu.
CANCEL or NO Selecting this word cancels the operation in the present 
menu and returns to the previous menu.
OK or YES Selecting this word executes the prepared function or shifts 
the menu to the next menu. 
						

							32
EASY MENU
EASY MENU
From the EASY MENU, items shown in the table 
below can be performed.
Select an item using the ▲/▼ cursor buttons. Then 
perform it according to the following table.
ItemDescription
ASPECT Using the ◄/► buttons switches the mode for aspect ratio.
See the ASPECT item in IMAGE menu (

37
).
D-ZOOM Using the ◄/► cursor buttons adjusts the magnification ratio.
Small  ó Large
See the D-ZOOM item in the SETUP menu (
 44
).
•  The on-screen menu might be displayed outside of the image 
display area depending on the adjustment value of the ASPECT, 
D-ZOOM and  
 KEYSTONE . Changing the values of ASPECT, 
D-ZOOM and   KEYSTONE may fix the symptom.
 KEYSTONE Using the ◄/► buttons corrects the vertical keystone distortion.
See the  
KEYSTONE item in SETUP menu ( 45
).
(continued on next page) 
						

							33
EASY MENU
ItemDescription
PICTURE MODE Using the ◄/► buttons switches the picture mode.
The picture modes are combinations of GAMMA and COLOR TEMP 
settings. Choose a suitable mode according to the projected source.
 NORMAL   ó  CINEMA  
ó  DYNAMIC  
ó  BOARD(BLACK)
　
 PHOTO  ó DAYTIME 
ó WHITEBOARD 
ó BOARD(GREEN)
• When the combination of GAMMA and COLOR TEMP differs 
from pre-assigned modes above, the display on the menu for the 
PICTURE MODE is “CUSTOM”. Please refer to the GAMMA and 
COLOR TEMP (
 34, 35
) items in PICTURE menu.
• Lines or other noise might appear on the screen when this function 
is operated, but it is not a malfunction.
ECO MODE Using the ◄/► buttons changes the eco mode setting.
See the ECO MODE item of the LAMP & FILTER item in SETUP 
menu (

46
).
• When the ambient temperature is around 35 to 40°C, the 
brightness of lamp is reduced automatically.
INSTALLATION Pressing the ► button displays the INSTALLATION dialog.
See the INSTALLATION item in SETUP menu (

48
).
RESET Performing this item resets all of the EASY MENU items except the 
FILTER TIME and LANGUAGE.
A dialog is displayed for confirmation. Selecting the OK using the ► 
button performs resetting.
FILTER TIME The usage time of the air filter is shown in the menu.
Performing this item resets the filter time which counts usage time 
of the air filter.
A dialog is displayed for confirmation. Selecting the OK using the ► 
button performs resetting. 
See the FILTER TIME item of the LAMP & FILTER item in SETUP 
menu (

47
).
LANGUAGE Using the ◄/► buttons changes the display language. 
See the LANGUAGE item in SCREEN menu
 (
52
).
ADVANCED MENUPress the ► or  ENTER button to use the menu of PICTURE, 
IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION, NETWORK or 
SECURITY.
EXIT Press the ◄ or  ENTER button to finish the OSD menu. 
						

							34
PICTURE menu
PICTURE menu
From the PICTURE menu, items shown in the table 
below can be performed. 
Select an item using the ▲/▼ cursor buttons, and press 
the ► cursor button or ENTER button to execute the 
item. Then perform it according to the following table.
ItemDescription
BRIGHTNESS Using the 
◄/► buttons adjusts the brightness.
Dark  ó Light
CONTRAST Using the 
◄/► buttons adjusts the contrast.
Weak  ó Strong
HDCR A function to show a clear picture in a bright room.
 
Using the ◄/► buttons adjusts the contrast.
• This function may not work properly when IMAGE OPTIMIZER is
enabled.
ACCENTUALIZER ACCENTUALIZER is a function to improve the legibility.
Using the ◄/► buttons adjusts the sharpness.
    Weak 
ó Strong
• There may be some noise and/or the screen may flicker for a
moment when an adjustment is made. This is not a malfunction.
• This function may not work properly when IMAGE OPTIMIZER is
enabled.
GAMMA Using the ▲/▼ buttons switches the gamma mode.
To adjust CUSTOM
Selecting a mode whose name includes CUSTOM and then 
pressing the ► button or the  ENTER button displays   
a dialog to aid you in adjusting the mode.  
This function is useful when you want to   
change the brightness of particular tones.
Choose an item using the ◄/► buttons,  
and adjust the level using the ▲/▼ buttons.
You can display a test pattern for checking the effect of your 
adjustment by pressing the  ENTER button. 
Each time you press the  ENTER button, the  
pattern changes as below.
  No pattern  ð Gray scale of 9 steps 
     Ramp 
 Gray scale of 15 steps
The  eight  equalizing  bars  correspond  to  eight  tone  levels  of  the  test 
pattern (Gray scale of 9 steps) except the darkest in the left end. If you 
want  to  adjust  the  2nd  tone  from  left  end  on  the  test  pattern,  use  the 
equalizing  adjustment  bar  “1”.  The  darkest  tone  at  the  left  end  of  the 
test pattern cannot be controlled with any of equalizing adjustment bar.
• Lines or other noise might appear on the 
screen when this function is operated, but it 
is not a malfunction. 
						

							35
PICTURE menu
(continued on next page)
ItemDescription
COLOR TEMP Using the ▲/▼ buttons switches the color temperature mode.
To adjust CUSTOM
Selecting a mode whose name includes 
CUSTOM and then pressing the ► button 
or the 
ENTER  button displays a dialog 
to aid you in adjusting the OFFSET and 
GAIN of the selected mode.
OFFSET adjustments change the color intensity on the whole tones 
of the test pattern.
GAIN adjustments mainly affect color intensity on the brighter tones 
of the test pattern.
Choose an item using the ◄/► buttons, and adjust the level using 
the ▲/▼ buttons. 
You can display a test pattern for checking the effect of your 
adjustment by pressing the  ENTER button.  
Each time you press the  ENTER button, the pattern changes as below.
No pattern 
ð Gray scale of 9 steps  
     
 Ramp   Gray scale of 15 steps
• Lines or other noise might appear on the screen 
when this function is operated, but it is not a 
malfunction.
COLOR Using the ◄/► buttons adjusts the strength of whole color.
Weak  ó Strong
• This item can be selected only for a video and component video 
signal. 
• 
For an HDMITM signal, this item can also be selected if either (1) or (2) applies. (1) HDMI FORMAT item in the INPUT menu is set to VIDEO.
(2)   HDMI FORMAT item in the INPUT menu is set to AUTO, and the 
projector recognizes that it receives video signals.
TINT Using the ◄/► buttons adjusts the tint.
Reddish  ó Greenish
• This item can be selected only for a video and component video 
signal.
• 
For an HDMITM signal, this item can also be selected if either (1) or (2) applies. 
(1) HDMI FORMAT item in the INPUT menu is set to VIDEO.
(2)   HDMI FORMAT item in the INPUT menu is set to AUTO, and the 
projector recognizes that it receives video signals. 
						

							36
PICTURE menu
ItemDescription
SHARPNESS Using the ◄/► buttons adjusts the sharpness.
Weak  ó Strong
•  There may be some noise and/or the screen may flicker for a 
moment when an adjustment is made. This is not a malfunction.
ACTIVE IRIS
Using the ▲/▼ cursor buttons changes the active iris control mode.
PRESENTATION   ó  THEATER  
ó  OFF              
PRESENTATION : 
 
The active iris displays the best presentation 
image for both bright and dark scenes.
THEATER :   
The active iris displays the best theater image for 
both bright and dark scenes.
OFF  :  
The active iris is always open.
• The screen may flicker when the PRESENTATION or THEATER 
modes are selected. If this occurs select OFF.
MY MEMORY
This projector has 4 memories for adjustment data (for all the items 
of the PICTURE menu).
Selecting a function using the ▲/▼ buttons and pressing the ► or 
ENTER  button performs each function.
SAVE-1  ó SAVE-2 
ó SAVE-3 
ó SAVE-4
LOAD-4  óLOAD-3 
ó LOAD-2 
ó LOAD-1
SAVE-1, SAVE-2, SAVE-3, SAVE-4
Performing a SAVE function saves the current adjustment data into 
the memory linked in the number included in the function’s name. 
• Remember that the current data being stored of a memory will be 
lost by saving new data into the memory.
LOAD-1, LOAD-2, LOAD-3, LOAD-4
Performing a LOAD function loads the data from the memory linked 
in the number included in the function’s name, and adjusts the 
picture automatically depending on the data. 
• The LOAD functions whose linked memory has no data are 
skipped.
• Remember that the current adjusted condition will be lost by 
loading data. If you want to keep the current adjustment, please 
save it before performing a LOAD function.
• There may be some noise and the screen may flicker for a 
moment when loading data. This is not malfunction.
• You can perform the LOAD function using  MY BUTTON. Please 
see MY BUTTON item in OPTION menu (
 60
). 
						

							37
IMAGE menu
IMAGE menu
From the IMAGE menu, items shown in the table 
below can be performed.
Select an item using the ▲/▼ cursor buttons, and 
press the ► cursor button or ENTER button to 
execute the item. Then perform it according to the 
following table.
ItemDescription
ASPECT Using the ▲/▼ buttons switches the mode for aspect ratio.
 
For a computer signal
NORMAL  ó 4:3 
ó 16:9 
ó 16:10 
ó NATIVE
          
For an HDMITM signal
NORMAL  
ó  
4:3  
ó  
16:9  
ó  
16:10  
ó  
14:9  
ó  NATIVE
 
  
For a video signal or component video signal
4:3  ó 16:9 
ó 16:10 
ó 14:9 
ó NATIVE
     
For an input signal from the LAN, USB TYPE A or USB TYPE B 
port, or if there is no signal
CP-BX301WN: 4:3 (fixed)
CP-BW301WN: 16:10 (fixed)
• The NORMAL mode keeps the original aspect ratio of the signal.
OVER SCAN Using the ◄/► buttons adjusts the over-scan ratio.
Small (It magnifies picture)  ó Large (It reduces picture)
• This item can be selected only for a video and component video 
signal.
• For an HDMI
TM signal, this item can also be selected if either (1) or 
(2) applies. 
(1) HDMI FORMAT item in the INPUT menu is set to VIDEO.
(2)   HDMI FORMAT item in the INPUT menu is set to AUTO, and the 
projector recognizes that it receives video signals.
(continued on next page) 
						

							38
IMAGE menu
ItemDescription
V POSITION Using the ◄/► buttons adjusts the vertical position.
Down  ó Up
• Over-adjusting the vertical position may cause noise to appear on 
the screen. If this occurs, please reset the vertical position to the 
default setting. Pressing the  RESET button when the V POSITION 
is selected will reset the V POSITION to the default setting.
• When this function is performed on a video signal, the range of 
this adjustment depends on OVER SCAN (
 37
) setting. It is not 
possible to adjust when OVER SCAN is set to 10.
•
 This function is unavailable for a signal from the LAN,  USB TYPE A, 
USB TYPE B or HDMI 1/2 port.
H POSITION Using the ◄/► buttons adjusts the horizontal position.
Right  ó Left 
• 
Over-adjusting the horizontal position may cause noise to appear on 
the screen. If this occurs, please reset the horizontal position to the 
default setting. Pressing the  RESET button when the H POSITION is 
selected will reset the H POSITION to the default setting.
• When this function is performed on a video signal, the range of 
this adjustment depends on OVER SCAN  (
37
) setting. It is not 
possible to adjust when OVER SCAN is set to 10.
•  
This function is unavailable for a signal from the  LAN, USB TYPE A , 
USB TYPE B  or HDMI 1/2  por
t.
(continued on next page) 
						

							39
IMAGE menu
ItemDescription
H PHASE
Using the ◄/► buttons adjusts the horizontal phase to eliminate flicker.
Right  ó Left
• This item can be selected only for a computer signal or a 
component video signal. This function is unavailable for a signal 
from the  LAN, USB TYPE A , USB TYPE B  or HDMI 1/2  port.
H SIZE Using the ◄/► buttons adjusts the horizontal size.
Small  ó Large
• This item can be selected only for a computer signal. This function 
is unavailable for a signal from the  LAN, USB TYPE A , USB TYPE 
B  or  HDMI 1/2  port.
• When this adjustment is excessive, the picture may not be 
displayed correctly. In such a case, please reset the adjustment 
by pressing the  RESET button on the remote control during this 
operation.
• Images might appear degraded when this function is operated, but 
it is not a malfunction.
AUTO ADJUST  EXECUTE Selecting this item performs the automatic adjustment feature.
For a computer signal
The vertical position, the horizontal position and the horizontal 
phase will be automatically adjusted. 
 
Make sure that the application window is set to its maximum size 
prior to attempting to use this feature. A dark picture may still be 
incorrectly adjusted. Use a bright picture when adjusting.
For a video signal
The video format best suited for the respective input signal will 
be selected automatically. This function is available only when 
the AUTO is selected for the VIDEO FORMAT item in the INPUT 
menu (
 41
). The vertical position and horizontal position will be 
automatically set to the default.
For a component video signal
The vertical position and horizontal position will be automatically 
set to the default. The horizontal phase will be automatically 
adjusted.
• The automatic adjustment operation requires approx. 10 seconds. 
Also please note that it may not function correctly with some input. 
• When this function is performed for a video signal, a certain extra 
such as a line may appear outside a picture.
• When this function is performed for a computer signal, a black 
frame may be displayed on the edge of the screen, depending on 
the PC model. 
• The items adjusted by this function may vary when the FINE or 
DISABLE is selected for the AUTO ADJUST item of the SERVICE 
item in the OPTION menu (
 64
). 
						

							40
INPUT menu
INPUT menu
From the INPUT menu, items shown in the table 
below can be performed.
Select an item using the ▲/▼ cursor buttons, and 
press the ► cursor button or ENTER button to 
execute the item. Then perform it according to the 
following table.
ItemDescription
PROGRESSIVE Using the ▲/▼ buttons switches the progress mode.
TV  ó FILM 
ó OFF
  
• This function works only for a video signal, component video signal 
(of 480i@60 or 576i@50 or 1080i@50/60) and an HDMITM signal (of 
480i@60 or 576i@50 or 1080i@50/60).
• When TV or FILM is selected, the screen image will be sharp. 
FILM adapts to the 2-3 Pull-Down conversion system. But these 
may cause a certain defect (for example, jagged line) of the picture 
for a quick moving object. In such a case, please select OFF, even 
though the screen image may lose sharpness.
VIDEO NR Using the ▲/▼ buttons switches the noise reduction mode.
HIGH  ó MID 
ó LOW
   
• This function works only for a video signal, component video signal 
(of 480i@60 or 576i@50 or 1080i@50/60) and an HDMITM signal (of 
480i@60 or 576i@50 or 1080i@50/60). 
COLOR SPACE Using the ▲/▼ buttons switches the mode for color space.
AUTO  ó RGB 
ó SMPTE240 
ó REC709 
ó REC601
      
• This item can be selected only for a computer signal, component 
video signal(except for signals from the  LAN, USB TYPE A  and 
USB TYPE B  ports) or an HDMI™ signal.
• The AUTO mode automatically selects the optimum mode.
• The AUTO operation may not work well at some signals. In such a 
case, it might be good to select a suitable mode except AUTO.
(continued on next page)