Hitachi Cp-X600 Projector Users Manual



Setting up
NOTE  • Be sure to read the manuals for devices before connecting them to\
 the 
projector, and make sure that all the devices are suitable to be connected with t\
his 
product. Before connecting to a PC, check the signal level, the signal t\
iming, and the 
resolution.
-  Some signal may need an adapter to input this projector.
-   Some PCs have multiple screen display modes that may include some signal\
s which 
are not supported by this projector. 
-    Although the projector...



Setting up
Connecting power supply
. Connect the connector of the power cord to the AC inlet of the projector.
. Firmly plug the power cord's plug into the outlet. 
WARNING  ►Please use extra caution when connecting the power cord, as 
incorrect or faulty connections may result in fire and/or electrical shock.
• Only use the power cord that came with the projector. If it is damaged, contact 
your dealer to newly get correct one.
• Only plug the power cord into an outlet rated...

3

Remote control
Putting batteries
Please load the batteries before using the remote control. If the remote\
 control starts to 
malfunction, replace the batteries. If you will not use the remote contr\
ol for an extended 
period, remove the batteries from the remote control and store them in a\
 safe place.
. Slide back and remove the 
battery cover in the direction 
of the arrow.
. Align and insert the two AA 
batteries according to their 
plus and minus   terminals as indicated in the...

4
About the remote control signal
The  remote  control  works  with  the  projector’s  remote  sensors.  This  projector  has  three remote sensors on the front, on the top, and on the back.The  sensors  can  be  respectively  turned  active  or  inactive  using  the  “REMOTE  RECEIV” in  the  SERVICE  item  of  OPTION  menu (46).  Each  sensor  senses  the  signal  within  the following range when the sensor is active.
The front and top sensors:60  degrees  (30  degrees  to  the  left  and  right...

5
Power on/off
Turning on the power
. Make sure that the power cord is firmly and correctly connected to the projector and the outlet.
. Remove the lens cover, and set the power switch to the ON position.  The power indicator will light up in steady orange (58). Then wait several seconds because the buttons may not function for these several seconds. 
(1) When AUTO ON in OPTION menu is set to TURN ON (41) :The lamp will only be automatically turned on when the Power switch is turned on...

6

Operating
Operating
Adjusting the volume
. Press the VOLUME button on the remote control. 
A dialog will appear on the screen to aid you in adjusting the volume.
. Use the cursor buttons ▲/▼ to adjust the volume.
To close the dialog and complete the operation, press the 
VOLUME button again. Even if you do not do anything, the 
dialog will automatically disappear after a few seconds.
● When no audio port is selected for current picture input port, the volume 
adjustment is disable....

7

Operating
Searching an input signal
. Press the SEARCH button on the remote control.
The projector will start to check its input ports in order to 
find any input signals.
When an input is found, the projector will stop searching and display th\
e image. 
If no signal is found, the projector will return to the state selected b\
efore the 
operation.
RGB   RGB   COMPONENT (Y, CB/RB, CR/BR)  S-VIDEO  VIDEO 
   
Selecting an input signal (continued)
. Press the VIDEO button...

8

Adjusting the zoom and focus
. Use the zoom ring to adjust the screen size.  
. Use the focus ring to focus the picture.
Operating
Focus ringZoom ring
Using the automatic adjustment feature
. Press the AUTO button on the remote control.  
 For an RGB signal 
The vertical position, the horizontal position, the horizontal 
phase and the horizontal size will be automatically adjusted. 
And the aspect ratio will be automatically set to default. Make sure tha\
t the 
application...

9

Adjusting the position
. Press the POSITION button on the remote control. 
The “POSITION” indication will appear on the screen.
. Use the cursor buttons ▲/▼/◄/► to adjust the picture 
position.
When you want to reset the operation, press the RESET button on the remote 
control during the operation.
To complete this operation, press the POSITION button again. Even if you \
do 
not do anything, the dialog will automatically disappear after a few sec\
onds.
● When this function is...

0

Operating
Using the magnify feature
. Press the ON button of MAGNIFY on the remote control.   
The “MAGNIFY” indication will appear on the screen 
(although the indication will disappear in several seconds with 
no operation), and the projector will go into the MAGNIFY 
mode.
. Use the cursor buttons ▲/▼ to adjust the zoom level. 
To move the zoom area, press the POSITION button in the MAGNIFY mode, 
then use the cursor buttons ▲/▼/◄/► to move the area. And to finalize the 
zoom area,...