Hitachi Cp X417 Projector Technical Manual


Projector
CP-X417
User's Manual (detailed)
Technical
Resolution (H x V)H. frequency (kHz)V. frequency (Hz)RatingSignal mode
720 x 40037.985.0VESATEXT
640 x 4803.559.9VESAVGA (60Hz)
640 x 48037.972.8VESAVGA (72Hz)
640 x 48037.575.0VESAVGA (75Hz)
640 x 48043.385.0VESAVGA (85Hz)
800 x 60035.256.3VESASVGA (56Hz)
800 x 60037.960.3VESASVGA (60Hz)
800 x 60048.72.2VESASVGA (72Hz)
800 x 60046.975.0VESASVGA (75Hz)
800 x 60053.785.VESASVGA (85Hz)
832 x 62449.774.5 Mac 6” mode
024...

2

Initial set signals
Initial set signals
The  following  signals  are  used  for  the  initial  settings.  The  signal  timing  of  some 
PC  models  may  be  different.  In  such  case,  adjust  the  items  V  POSITION  and  H 
POSITION in IMAGE menu. 
 
computer Signal
Horizontal signal timing (μs)computer Signal
Vertical signal timing (lines)
(A)(B)(C)(D)(a)(b)(c)(d)
TEXT2.03.020.3.0TEXT342400
VGA (60Hz)3.8.925.40.6VGA (60Hz)233480 0
VGA (72Hz) .34.20.30.8VGA...

3

BATTERY
SD CARD
DC 5V 0.5A
USB STORAGELAN
AUDIO IN3
CONTROLAUDIO OUT
COMPUTER IN1COMPUTER IN2MONITOR OUTHDMI
AUDIO IN
S-VIDEOUSB

ACOMPUTER IN1, BCOMPUTER IN2, CMONITOR OUT
 D-sub 5pin mini shrink jack
•  Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω 
terminated (positive)
• H/V. sync. signal: TTL level (positive/negative)
• Composite sync. signal: TTL level
PinSignalPinSignal
Video Red 0Ground
2Video Green(No connection)
3Video Blue
2A: SDA (DDC data)
B, C: (No...

4

BATTERY
SD CARD
DC 5V 0.5A
USB STORAGELAN
AUDIO IN3
CONTROLAUDIO OUT
COMPUTER IN1COMPUTER IN2MONITOR OUTHDMI
AUDIO IN
S-VIDEOUSB

Connection to the ports (continued)
432
IVIDEO
RCA jack
• System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4.43
• 1.0±0.1Vp-p, 75Ω terminator
HS-VIDEO
Mini DIN 4pin jack
PinSignal
Color signal 0.286Vp-p (NTSC, burst), 75Ω terminator
Color signal 0.300Vp-p (PAL/SECAM, burst) 75Ω terminator
2Brightness signal, 1.0Vp-p, 75Ω terminator
3Ground
4Ground
GE
I
H
COMPONENT...

5

BATTERY
SD CARD
DC 5V 0.5A
USB STORAGELAN
AUDIO IN3
CONTROLAUDIO OUT
COMPUTER IN1COMPUTER IN2MONITOR OUTHDMI
AUDIO IN
S-VIDEOUSB

Connection to the ports (continued)
JAUDIO IN1, KAUDIO IN2
Ø3.5 stereo mini jack
• 200 mVrms 47kΩ terminator
AUDIO IN3 LL, MR
RCA jack x2
• 200 mVrms 47kΩ terminator
NAUDIO OUT
Ø3.5 stereo mini jack
• 200 mVrms 1kΩ output impedance
To input SCART RGB signal;
  ex.:
To input SCART RGB signal to the projector, use a SCART to RCA cable. 
Connect the plugs refer to above ex.....

6

BATTERY
SD CARD
DC 5V 0.5A
USB STORAGELAN
AUDIO IN3
CONTROLAUDIO OUT
COMPUTER IN1COMPUTER IN2MONITOR OUTHDMI
AUDIO IN
S-VIDEOUSB

Connection to the ports (continued)
OUSB
USB B type jack
PinSignal
+5V
2- Data
3+ Data
4Ground
2
34
PCONTROL
D-sub 9pin plug
• About the details of RS-232C communication,  
please refer to the following page.
PinSignalPinSignalPinSignal
(No connection)4(No connection)7RTS
2RD5Ground8CTS
3TD6(No connection)9(No connection)
9
2345
678
QLAN
RJ-45 jack...

7

BATTERY
SD CARD
DC 5V 0.5A
USB STORAGELAN
AUDIO IN3
CONTROLAUDIO OUT
COMPUTER IN1COMPUTER IN2MONITOR OUTHDMI
AUDIO IN
S-VIDEOUSB

Connection to the ports (continued)
RUSB STORAGE
USB A type jack432
PinSignal
+5V
2- Data
3+ Data
4Ground
SSD card slot
SD card slot
PinSignalPinSignalPinSignal
CD/DAT 34VDD7DAT 0
2CMD5CLK8DAT 
3VSS6VSS9DAT 2
98765432
SR 

8

RS-232C Network Communication
RS-232C Network Communication
Connecting the cable
. Turn off the projector and the computer. 
2. Connect the CONTROL port of the projector with a RS-232C port of 
the computer by a RS-232C cable (cross). Use the cable that fulfills the 
specification shown in the previous page.
3. Turn the computer on, and after the computer has started up turn the 
projector on.
Communications setting
9200bps, 8N
1. Protocol
Consist of header (7 bytes) + command data (6...

9

RS-232C Network Communication (continued)
Requesting projector status (Get command)
() Send the following request code from the PC to the projector.
	 Header	+	Command	data	(‘02H’	+	‘00H’	+	type	(2	bytes)	+	‘00H’ 	+	‘00H’)	
(2) The projector returns the response code  ‘1DH’	+	data	(2	bytes)
 to the PC.
Changing the projector settings (Set command)
() Send the following setting code from the PC to the projector.
		 Header	+	Command	data	(‘01H’ 	+	‘00H’	+	type	(2	bytes)	+	setting	code	(2...

0

Command Control via the Network
Communication Port
The following two ports are assigned for the command control.
TCP #23
TCP #975
Command Control Settings
Configure the following items form a web browser when command control is used.
When the authentication setting is enabled, the following settings are r\
equired.
Command Control via the Network
Port Settings
Netowrk Control Port1 (Port: 23)
Port openClick the [Enable] check box to open [Network Control Port1 (Port: 23)] to use TCP...