Home > Hitachi > Projector > Hitachi Cp X417 Projector Technical Manual

Hitachi Cp X417 Projector Technical Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Hitachi Cp X417 Projector Technical Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 913 Hitachi manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							
    
    Projector
    CP-X417
    User's Manual (detailed)
    Technical
    Resolution (H x V)H. frequency (kHz)V. frequency (Hz)RatingSignal mode
    720 x 40037.985.0VESATEXT
    640 x 4803.559.9VESAVGA (60Hz)
    640 x 48037.972.8VESAVGA (72Hz)
    640 x 48037.575.0VESAVGA (75Hz)
    640 x 48043.385.0VESAVGA (85Hz)
    800 x 60035.256.3VESASVGA (56Hz)
    800 x 60037.960.3VESASVGA (60Hz)
    800 x 60048.72.2VESASVGA (72Hz)
    800 x 60046.975.0VESASVGA (75Hz)
    800 x 60053.785.VESASVGA (85Hz)
    832 x 62449.774.5 Mac 6” mode
    024 x 768
    48.460.0VESAXGA (60Hz)
    024 x 768
    56.5 70.VESAXGA (70Hz)
    024 x 768
    60.075.0VESAXGA (75Hz)
    024 x 768
    68.785.0VESAXGA (85Hz)
    52 x 864
    67.575.0VESA52 x 864 (75Hz)
    280 x 96060.060.0VESA280 x 960 (60Hz)
    280 x 02464.060.0VESASXGA (60Hz)
    280 x 024
    80.075.0VESASXGA (75Hz)
    *280 x 024 9.
    85.0VESASXGA (85Hz)
    *600 x 200
    75.060.0VESAUXGA (60Hz)
    280 x 768
    47.760.0VESAW-XGA (60Hz)
    400 x 050
    65.260.0VESASXGA+ (60Hz)
    NOTE   • Be sure to check jack type, signal level, timing and resolution before 
    connecting this projector to a PC.
    •  Some  PCs  may  have  multiple  display  screen  modes.  Use  of  some  of  these 
    modes will not be possible with this projector.
    •  Depending  on  the  input  signal,  full-size  display  may  not  be  possible  in  some 
    cases. Refer to the number of display pixels above.
    •   A l t h o u g h   t h e   p r o j e c t o r   c a n   d i s p l a y   s i g n a l s   w i t h   r e s o l u t i o n   u p   t o   U X G A 
    (600x200), the signal will be converted to the projector’s panel resolution before 
    being  displayed.  The  best  display  performance  will  be  achieved  if  the  resolutions 
    of the input signal and projector panel are identical.
    • Automatic adjustment may not function correctly with some input signals.\
    •  The  image  may  not  be  displayed  correctly  when  the  input  sync  signal  is  a 
    composite sync or a sync on G.
    • The HDMI input does not support the signals marked with *.
    Example of PC signal 
    						
    							
    2
    
    Initial set signals
    Initial set signals
    The  following  signals  are  used  for  the  initial  settings.  The  signal  timing  of  some 
    PC  models  may  be  different.  In  such  case,  adjust  the  items  V  POSITION  and  H 
    POSITION in IMAGE menu. 
     
    computer Signal
    Horizontal signal timing (μs)computer Signal
    Vertical signal timing (lines)
    (A)(B)(C)(D)(a)(b)(c)(d)
    TEXT2.03.020.3.0TEXT342400
    VGA (60Hz)3.8.925.40.6VGA (60Hz)233480 0
    VGA (72Hz) .34.20.30.8VGA (72Hz)3284809
    VGA (75Hz)2.03.820.30.5VGA (75Hz)36480
    VGA (85Hz) .62.27.8 .6VGA (85Hz)325480
    SVGA (56Hz)2.03.622.20.7SVGA (56Hz)222600
    SVGA (60Hz)3.22.220.0.0SVGA (60Hz)423600
    SVGA (72Hz)2.4.36.0 .SVGA (72Hz)62360037
    SVGA (75Hz) .63.26.20.3SVGA (75Hz)32600
    SVGA (85Hz) .2.74.20.6SVGA (85Hz)327600
    Mac 6" mode .
    3.94.50.6 Mac 6" mode339624
    XGA (60Hz) 2.2.55.80.4XGA (60Hz)6297683
    XGA (70Hz) .8.93.70.3XGA (70Hz)6297683
    XGA (75Hz) .22.23.00.2XGA (75Hz)328768
    XGA (85Hz) .02.20.80.5XGA (85Hz)336768
    52 x 864 
    (75Hz) .22.4
    0.70.6 52 x 864 (75Hz)332864
    280 x 960 
    (60Hz) .02.9
    .90.9 280 x 960 (60Hz)336960
    SXGA (60Hz)
    .02.3.90.4SXGA(60Hz)338024
    SXGA (75Hz) ..89.50.SXGA (75Hz)338024
    SXGA (85Hz) .0.48.0.4SXGA (85Hz)344024
    UXGA (60Hz) .2.99.90.4UXGA (60Hz)346200
    W-XGA (60Hz) .72.56.00.8W-XGA (60Hz)323768
    SXGA+ (60Hz) .22.0.40.7SXGA+ (60Hz)333050
     Back porch (B) Front porch (D) Back porch (b) Front porch (d)
     Active video (C) 
    Data Data
    H. Sync. V. Sync.
    Sync (A)  Sync (a)
    Active video (c)  
    						
    							
    3
    
    BATTERY
    SD CARD
    DC 5V 0.5A
    USB STORAGELAN
    AUDIO IN3
    CONTROLAUDIO OUT
    COMPUTER IN1COMPUTER IN2MONITOR OUTHDMI
    AUDIO IN
    S-VIDEOUSB
    
    ACOMPUTER IN1, BCOMPUTER IN2, CMONITOR OUT
     D-sub 5pin mini shrink jack
    •  Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω 
    terminated (positive)
    • H/V. sync. signal: TTL level (positive/negative)
    • Composite sync. signal: TTL level
    PinSignalPinSignal
    Video Red 0Ground
    2Video Green(No connection)
    3Video Blue
    2A: SDA (DDC data)
    B, C: (No connection)4(No connection)
    5Ground3H. sync / Composite sync.
    6Ground Red4V. sync.
    7Ground Green
    5A: SCL (DDC clock)
    B, C: (No connection)8Ground Blue
    9(No connection)--
    Connection to the ports
    
    Connection to the ports
    BDAC
    DHDMI
    • Type :Digital audio/video connector
    • Audio signal : Linear PCM (Sampling rate; 32/44./48 KHz)
    PinSignalPinSignalPinSignal
    T.M.D.S. Data2 +8T.M.D.S. Data0 Shield 5SCL2T.M.D.S. Data2 Shield9T.M.D.S. Data0 -6SDA3T.M.D.S. Data2 - 0T.M.D.S. Clock +7DDC/CEC Ground4T.M.D.S. Data +T.M.D.S. Clock Shield8+5V Power5T.M.D.S. Data Shield 2T.M.D.S. Clock -9Hot Plug Detect6T.M.D.S. Data - 3CEC7T.M.D.S. Data0 +4Reserved(N.C. on device) 
    						
    							
    4
    
    BATTERY
    SD CARD
    DC 5V 0.5A
    USB STORAGELAN
    AUDIO IN3
    CONTROLAUDIO OUT
    COMPUTER IN1COMPUTER IN2MONITOR OUTHDMI
    AUDIO IN
    S-VIDEOUSB
    
    Connection to the ports (continued)
    432
    IVIDEO
    RCA jack
    • System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4.43
    • 1.0±0.1Vp-p, 75Ω terminator
    HS-VIDEO
    Mini DIN 4pin jack
    PinSignal
    Color signal 0.286Vp-p (NTSC, burst), 75Ω terminator
    Color signal 0.300Vp-p (PAL/SECAM, burst) 75Ω terminator
    2Brightness signal, 1.0Vp-p, 75Ω terminator
    3Ground
    4Ground
    GE
    I
    H
    COMPONENT VIDEO E Y, F Cb/Pb, G Cr/Pr
    RCA jack x3
    • System: 525i(480i), 525p(480p), 625i(576i), 750p(720p),25i(080i)
    PortSignal
    YComponent video Y, 1.0±0.1Vp-p, 75Ω terminator with composite sync
    Cb/PbComponent video Cb/Pb, 0.7±0.1Vp-p, 75Ω terminator
    Cr/PrComponent video Cr/Pr, 0.7±0.1Vp-p, 75Ω terminator
    F 
    						
    							
    5
    
    BATTERY
    SD CARD
    DC 5V 0.5A
    USB STORAGELAN
    AUDIO IN3
    CONTROLAUDIO OUT
    COMPUTER IN1COMPUTER IN2MONITOR OUTHDMI
    AUDIO IN
    S-VIDEOUSB
    
    Connection to the ports (continued)
    JAUDIO IN1, KAUDIO IN2
    Ø3.5 stereo mini jack
    • 200 mVrms 47kΩ terminator
    AUDIO IN3 LL, MR
    RCA jack x2
    • 200 mVrms 47kΩ terminator
    NAUDIO OUT
    Ø3.5 stereo mini jack
    • 200 mVrms 1kΩ output impedance
    To input SCART RGB signal;
      ex.:
    To input SCART RGB signal to the projector, use a SCART to RCA cable. 
    Connect the plugs refer to above ex.. For more reference, please consult\
     your dealer.
    SCART connector(jack)
    SCART cable(plug)
    RCA plugs
    DC 5V 0.5A
    USB STORAGELAN
    AUDIO IN3
    AUDIO OUT
    COMPUTER IN2MONITOR OUTHDMI
    AUDIO INS-VIDEO:­:À:»:¼:Æ
    :©
    :™
    :ž
    :˜:Ì:»:À:Æ:w:£
    :˜:Ì:»:À:Æ:w:©
    LM
    NJ
    K 
    						
    							
    6
    
    BATTERY
    SD CARD
    DC 5V 0.5A
    USB STORAGELAN
    AUDIO IN3
    CONTROLAUDIO OUT
    COMPUTER IN1COMPUTER IN2MONITOR OUTHDMI
    AUDIO IN
    S-VIDEOUSB
    
    Connection to the ports (continued)
    OUSB
    USB B type jack
    PinSignal
    +5V
    2- Data
    3+ Data
    4Ground
    2
    34
    PCONTROL
    D-sub 9pin plug
    • About the details of RS-232C communication,  
    please refer to the following page.
    PinSignalPinSignalPinSignal
    (No connection)4(No connection)7RTS
    2RD5Ground8CTS
    3TD6(No connection)9(No connection)
    9
    2345
    678
    QLAN
    RJ-45 jack
    PinSignalPinSignalPinSignal
    TX +4-7-
    2TX -5-8-
    3RX +6RX ---
    8765432
    Q
    OP 
    						
    							
    7
    
    BATTERY
    SD CARD
    DC 5V 0.5A
    USB STORAGELAN
    AUDIO IN3
    CONTROLAUDIO OUT
    COMPUTER IN1COMPUTER IN2MONITOR OUTHDMI
    AUDIO IN
    S-VIDEOUSB
    
    Connection to the ports (continued)
    RUSB STORAGE
    USB A type jack432
    PinSignal
    +5V
    2- Data
    3+ Data
    4Ground
    SSD card slot
    SD card slot
    PinSignalPinSignalPinSignal
    CD/DAT 34VDD7DAT 0
    2CMD5CLK8DAT 
    3VSS6VSS9DAT 2
    98765432
    SR 
    						
    							
    8
    
    RS-232C Network Communication
    RS-232C Network Communication
    Connecting the cable
    . Turn off the projector and the computer. 
    2. Connect the CONTROL port of the projector with a RS-232C port of 
    the computer by a RS-232C cable (cross). Use the cable that fulfills the 
    specification shown in the previous page.
    3. Turn the computer on, and after the computer has started up turn the 
    projector on.
    Communications setting
    9200bps, 8N
    1. Protocol
    Consist of header (7 bytes) + command data (6 bytes)
    2. Header
    BE + EF + 03 + 06 + 00 + CRC_low + CRC_high
    CRC_low: Lower byte of CRC flag for command data
    CRC_high: Upper byte of CRC flag for command data
    3. Command data
    Command data chart
    byte_0byte_byte_2byte_3byte_4byte_5
    ActionTypeSetting code
    lowhighlowhighlowhigh
    Action (byte_0 - )
    ActionClassificationContent
    SetChange setting to desired value.
    2GetRead projector internal setup value.
    4Increment Increment setup value by .
    5DecrementDecrement setup value by .
    6ExecuteRun a command.
    67892345     67892345 
     CONTROL port  RS-232C cable (cross)  RS-232C port 
      of the projector   of the computer
     - () () CD 
      RD (2) (2) RD 
      TD (3) (3) TD 
      - (4) (4) DTR 
      GND (5) (5) GND 
      - (6) (6) DSR 
      RTS (7) (7) RTS 
      CTS (8) (8) DTS 
      - (9) (9) RI 
    						
    							
    9
    
    RS-232C Network Communication (continued)
    Requesting projector status (Get command)
    () Send the following request code from the PC to the projector.
    	 Header	+	Command	data	(‘02H’	+	‘00H’	+	type	(2	bytes)	+	‘00H’ 	+	‘00H’)	
    (2) The projector returns the response code  ‘1DH’	+	data	(2	bytes)
     to the PC.
    Changing the projector settings (Set command)
    () Send the following setting code from the PC to the projector.
    		 Header	+	Command	data	(‘01H’ 	+	‘00H’	+	type	(2	bytes)	+	setting	code	(2	bytes))	
    (2) The projector changes the setting based on the above setting code.
    (3) The projector returns the response code 	‘06H’	
    to the PC.
    Using the projector default settings (Reset Command)
    () The PC sends the following default setting code to the projector.
    	 Header	+	Command	data	(‘06H’ 	+	‘00H’	+	type	(2	bytes)	+	‘00H’ 	+	‘00H’)	
    (2) The projector changes the specified setting to the default value.
    (3) The projector returns the response code 	‘06H’
     to the PC.
    Increasing the projector setting value (Increment command)
    () The PC sends the following increment code to the projector.
    	 Header	+	Command	data	(‘04H’	+	‘00H’	+	type	(2	bytes)	+	‘00H’ 	+	‘00H’)	
    (2) The projector increases the setting value on the above setting code.
    (3) The projector returns the response code 
    ‘06H’ to the PC.
    Decreasing the projector setting value (Decrement command)
    () The PC sends the following decrement code to the projector.
    	 Header	+	Command	data	(‘05H’ 	+	‘00H’	+	type	(2	bytes)	+	‘00H’ 	+	‘00H’)
    (2) The projector decreases the setting value on the above setting code.
    (3) The projector returns the response code ‘06H’ to the PC.
    When the projector cannot understand the received command
    When the projector cannot understand the received command, the error code  ‘15H’	
    is sent back to the PC.
    Sometimes  the  projector  cannot  properly  receive  the  command.  In  such  a  case, 
    the  command  is  not  executed  and  the  error  code  ‘15H’	is  sent  back  to  the  PC.  If 
    this error code is returned, send the same command again.
    When the projector cannot execute the received command.
    When the projector cannot execute the received command, the error code  ‘1CH’	+	
    ‘xxxxH’ is sent back to the PC. 
    When  the  data  length  is  greater  than  indicated  by  the  data  length  code,  the 
    projector ignore the excess data code. Conversely when the data length is shorter 
    than indicated by the data length code, an error code will be returned t\
    o the PC.
    NOTE • Operation cannot be guaranteed when the projector receives an undefined command or data.• Provide an interval of at least 40ms between the response code and \
    any other code.• The projector outputs test data when the power supply is switched ON, and when the lamp is lit. Ignore this data.• Commands are not accepted during warm-up. 
    						
    							
    0
    
    Command Control via the Network
    Communication Port
    The following two ports are assigned for the command control.
    TCP #23
    TCP #975
    Command Control Settings
    Configure the following items form a web browser when command control is used.
    When the authentication setting is enabled, the following settings are r\
    equired.
    Command Control via the Network
    Port Settings
    Netowrk Control Port1 (Port: 23)
    Port openClick the [Enable] check box to open [Network Control Port1 (Port: 23)] to use TCP #23.Default setting is “Enable”.
    Authentication
    Click the [Enable] check box for the [Authentication] setting when authentication is required.Default setting is “Disable”.
    Network Control Port2 (Port: 9715)
    Port open
    Click the [Enable] check box to open [Network Control Port2 (Port: 9715)] to use TCP 
    #975.
    Default setting is “Enable”.
    Authentication
    Click the [Enable] check box for the [Authentication] setting when authentication is required.Default setting is “Enable”.
    Security Settings
    Network Control
    Authentication PasswordEnter the desired authentication password. This setting will be the same for [Network Control Port1 (Port: 23)] and [Network Control Port2 (Port: 9715)].Default setting is blank.
    Re-enter Authentication Password 
    						
    All Hitachi manuals Comments (0)

    Related Manuals for Hitachi Cp X417 Projector Technical Manual