Hitachi Cp-X385w Liquid Crystal Projector Users Manual

10
#AUDIO INAUDIO cable RGB cable
AUDIO OUT RGB IN
Analogue 
RGB OUT
AUDIO IN VIDEO IN S-VIDEO IN
AUDIO
INAUDIO OUT
112
2 USBRGB  IN
RGB  OUTCONTROL

#
Laptop computer
#%$USB INUSB OUT AUDIO IN
AUDIO OUT RGB INAnalogue 
RGB OUT CONTROL IN CONTROL OUT
If connecting to a 
USB port equipped 
computerRGB cable
AUDIO cable
USB cableMOUSE cable
AUDIO IN VIDEO IN S-VIDEO IN
AUDIO
INAUDIO OUT
112
2USBRGB  IN
RGB  OUTCONTROL

#%$
Desktop computer
CONNECTING YOUR DEVICES (continued)
Connecting to a Computer...

11
#$
*G
VTJOH
B
DPNQPOFOU

WJEFP
DPOOFDUJPO*G
VTJOH
BO
BVEJPWJEFP

DPOOFDUJPO
COMPONENT VIDEO INCOMPONENT VIDEO  OUTAUDIO/VIDEO INAUDIO/VIDEO OUT S-VIDEO INS-VIDEO OUT
If using a S-video 
connection
COMPONENT cable AUDIO/VIDEO cable
S-VIDEO cable
AUDIO IN VIDEO IN S-VIDEO IN
AUDIO
INAUDIO OUT
112
2USBRGB  IN
RGB  OUTCONTROL

###$
DVD player
#
If using a S-video
 connection
6%*07*%&0
*/ 6%*07*%&0
06547*%&0
*/
47*%&0
065
AUDIO/VIDEO cable
S-VIDEO cable
AUDIO IN VIDEO IN S-VIDEO IN
AUDIO
INAUDIO OUT...

12
RGB cable
3(#
065
3(#
*/
AUDIO IN VIDEO IN S-VIDEO IN
AUDIO
INAUDIO OUT
112
2USBRGB  IN
RGB  OUTCONTROL
CONNECTING YOUR DEVICES (continued)
Connecting to a Display Monitor
Display monitor
$19&/7	4
 
 
 
 1.
 
 

13
1Remove the battery
cover
Push the knob while lifting
up the battery cover in the
direction of the arrow.
Insert the batteries
Align and insert the two AA
batteries (that came with the
projector) according to their plus
and minus terminals (as indicated
in the remote control).
Close the battery
cover
Replace the battery cover
in the direction of the arrow
and snap it back into place.
• The remote control works with both the
projectors front and rear remote sensors.
• The range of the remote sensor on...

14
1Make sure that the power cord is firmly and
correctly connected to the projector and outlet
2Turn on the projectors power
Set the power switch to [ | ] (ON). The projector will go
to STANDBY mode and the POWER indicator will light to
solid orange.
3Press the STANDBY/ON button (control
panel or remote control) 
• The projector begins warming up and the POWER
indicator blinks green.
• The POWER indicator stops blinking and
lights to solid green once the projectors
power is completely on.
4Remove the...

RGB
15
6Use the zoom ring to adjust the
screen size
7Use the focus ring to focus the
picture
5
If selecting RGB input
Press the RGB button
Press this button to toggle between the
devices connected to RGB IN 1 and 2.
As illustrated below, each time you
press the RGB button, the projector
switches between RGB IN 1 and 2.
Select the signal you wish to project.
If selecting video input
Press the VIDEO button
Press this button to toggle between the
devices connected to VIDEO IN, S-
VIDEO IN and COMPONENT...

16
STANDBY/ONLASERBLANK
RGBVIDEO
AUTO
MENU
ENTER
KEYSTONE
RESET
FREEZE ASPECT
ESC
MAGNIFY
POSITION
OFF ONVOLUME
MUTE
1Press the STANDBY/ON button (control
panel or remote control)
The message Power off? will appear on the screen for approximately 5 seconds. 
3Check that the POWER indicator stops
blinking and lights to solid orange.
Switch the power switch to [O] (OFF).
4Confirm that the POWER indicator has
gone off and then attach the lens cap.
When the projector has completed powering down, the
POWER...

17
STANDBY/ONLASERBLANK
RGBVIDEO
AUTO
MENU
ENTERKEYSTONE
RESET
FREEZE ASPECT
ESC
MAGNIFY
POSITION
OFF ONVOLUME
SEARCH
MUTE
1Press the VOLUME button
As illustrated on the right, a dialog will
appear on the screen to aid you in adjusting
the volume.
1Press the MUTE button
As illustrated on the right, a dialog will appear on the
screen indicating that you have muted the sound.  Press
the VOLUME button to close the dialog.  (Even if you dont
do anything, the dialog will automatically disappear after
a few...

18
STANDBY/ONLASERBLANK
RGBVIDEO
AUTO
MENU
ENTERKEYSTONE
RESET
FREEZE ASPECT
ESC
MAGNIFY
POSITION
OFF ONVOLUME
SEARCH
MUTE
1Press the POSITION button
As illustrated on the right, a dialog will appear on the screen
to aid you in adjusting the position.
2Use the , , , buttons to adjust
the position
When you want to initialize the position, press the RESET
button during adjustment.
Press the POSITION button again to close the dialog and
complete this operation.  (Even if you dont do anything, the
dialog...

19
The automatic adjustment operation requires approximately 10 seconds. Also, please
note that it may not function correctly with some input signals.
NOTE
1
USING THE AUTOMATIC ADJUSTMENT FEATURE
Press the AUTO button
Horizontal position (H. POSIT), vertical position (V.
POSIT), clock phase (H. PHASE) and horizontal size (H.
SIZE) are automatically adjusted.
Make sure that the application window is set to its
maximum size prior to attempting to use this feature.
Dark pictures may still be incorrectly...