Hitachi Cp-X385w Liquid Crystal Projector Users Manual
Have a look at the manual Hitachi Cp-X385w Liquid Crystal Projector Users Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 913 Hitachi manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 8
7
Refer to the illustrations and tables below to determine the screen size and
projection distance.
Adjusting the Screen Size and Projection Distance
If 4:3 aspect ratio
4
3
The values shown in the table are calculated for a full size screen
a:Distance from the projector to the screen (±10%)
b:Distance from the lens center to the bottom of the screen (±10%)
c:Distance from the lens center to the top of the screen (±10%)
Top View
Side View
a
Screen size
[inches (m)]a[inches (m)]
Min.Max.
40 (1.0)62...](http://img.usermanuals.tech/thumb/33/91162/w64_hitachi-cp-x385w-wt-manual_d-7.png "Page 8
7
Refer to the illustrations and tables below to determine the screen size and
projection distance.
Adjusting the Screen Size and Projection Distance
If 4:3 aspect ratio
4
3
The values shown in the table are calculated for a full size screen
a:Distance from the projector to the screen (±10%)
b:Distance from the lens center to the bottom of the screen (±10%)
c:Distance from the lens center to the top of the screen (±10%)
Top View
Side View
a
Screen size
[inches (m)]a[inches (m)]
Min.Max.
40 (1.0)62...")
![Page 15
14
1Make sure that the power cord is firmly and
correctly connected to the projector and outlet
2Turn on the projectors power
Set the power switch to [ | ] (ON). The projector will go
to STANDBY mode and the POWER indicator will light to
solid orange.
3Press the STANDBY/ON button (control
panel or remote control)
• The projector begins warming up and the POWER
indicator blinks green.
• The POWER indicator stops blinking and
lights to solid green once the projectors
power is completely on.
4Remove the...](http://img.usermanuals.tech/thumb/33/91162/w64_hitachi-cp-x385w-wt-manual_d-14.png "Page 15
14
1Make sure that the power cord is firmly and
correctly connected to the projector and outlet
2Turn on the projectors power
Set the power switch to [ | ] (ON). The projector will go
to STANDBY mode and the POWER indicator will light to
solid orange.
3Press the STANDBY/ON button (control
panel or remote control)
• The projector begins warming up and the POWER
indicator blinks green.
• The POWER indicator stops blinking and
lights to solid green once the projectors
power is completely on.
4Remove the...")
10 #AUDIO INAUDIO cable RGB cable AUDIO OUT RGB IN Analogue RGB OUT AUDIO IN VIDEO IN S-VIDEO IN AUDIO INAUDIO OUT 112 2 USBRGB IN RGB OUTCONTROL # Laptop computer #%$USB INUSB OUT AUDIO IN AUDIO OUT RGB INAnalogue RGB OUT CONTROL IN CONTROL OUT If connecting to a USB port equipped computerRGB cable AUDIO cable USB cableMOUSE cable AUDIO IN VIDEO IN S-VIDEO IN AUDIO INAUDIO OUT 112 2USBRGB IN RGB OUTCONTROL #%$ Desktop computer CONNECTING YOUR DEVICES (continued) Connecting to a Computer ATTENTIONWhenever attempting to connect a laptop computer to the projector, be sure to activate the laptops RGB external image output (set the laptop to CRT display or to simultaneous LCD and CRT display). For details on how this is done, please refer to the instruction manual of the corresponding laptop computer. • Some computers may have multiple display screen modes. Use of some of these modes will not be possible with this projector. • For some RGB input modes, the optional Mac adapter is necessary. NOTE $19&/7 4 1.
11 #$ *GVTJOHBDPNQPOFOU WJEFPDPOOFDUJPO*GVTJOHBOBVEJPWJEFP DPOOFDUJPO COMPONENT VIDEO INCOMPONENT VIDEO OUTAUDIO/VIDEO INAUDIO/VIDEO OUT S-VIDEO INS-VIDEO OUT If using a S-video connection COMPONENT cable AUDIO/VIDEO cable S-VIDEO cable AUDIO IN VIDEO IN S-VIDEO IN AUDIO INAUDIO OUT 112 2USBRGB IN RGB OUTCONTROL ###$ DVD player # If using a S-video connection 6%*07*%&0*/ 6%*07*%&006547*%&0*/ 47*%&0065 AUDIO/VIDEO cable S-VIDEO cable AUDIO IN VIDEO IN S-VIDEO IN AUDIO INAUDIO OUT 112 2 USBRGB IN RGB OUTCONTROL # VCR Connecting to a DVD Player Connecting to a VCR $19&/7 4 1.
12 RGB cable 3(#065 3(#*/ AUDIO IN VIDEO IN S-VIDEO IN AUDIO INAUDIO OUT 112 2USBRGB IN RGB OUTCONTROL CONNECTING YOUR DEVICES (continued) Connecting to a Display Monitor Display monitor $19&/7 4 1.
13 1Remove the battery cover Push the knob while lifting up the battery cover in the direction of the arrow. Insert the batteries Align and insert the two AA batteries (that came with the projector) according to their plus and minus terminals (as indicated in the remote control). Close the battery cover Replace the battery cover in the direction of the arrow and snap it back into place. • The remote control works with both the projectors front and rear remote sensors. • The range of the remote sensor on the front and back is 3 meters with a 60-degree range (30 degrees to the left and right of the remote sensor). • Since the remote control uses infrared light to send signals to the projector (Class 1 LED), be sure to use the remote control in an area free from obstacles that could block the remote controls output signal to the projector. approximately 3 metersapproximately 3 meters 30 degrees30 degrees30 degrees30 degrees 23 USING THE REMOTE CONTROL CAUTIONPrecautions to observe in regards to the batteries Always handle the batteries with care and use them only as directed. Improper use may result in battery cracking or leakage, which could result in fire, injury and/or pollution of the surrounding environment. • Keep the battery away from children and pets. • Be sure to use only the batteries specified for use with the remote control. Do not mix new batteries with used ones. • When inserting batteries, verify that the plus and minus terminals are aligned correctly (as indicated in the remote control). • When you dispose the battery, you should obey the law in the relative area or country. Precautions to observe when using the remote control • Do not drop or otherwise expose the remote control to physical impact. • Do not get the remote control wet or place it on wet objects. Doing so may result in malfunction. • Remove the batteries from the remote control and store them in a safe place if you wont be using the remote control for an extended period. • Replace the batteries whenever the remote control starts to malfunction. • When strong light, such as direct sunlight or light from an extremely close range (such as from an inverter fluorescent lamp), hits the projectors remote sensor, the remote control may cease to function. Adjust the direction of the projector to keep light from directly hitting the projectors remote sensor. ATTENTION Putting batteries into the remote control unit Operating the remote control • Only use the accompanying remote control. Using other remote controls (even of similiar models) to control the CP-X385W may result in unexpected operation. $19&/7 4 1.
14 1Make sure that the power cord is firmly and correctly connected to the projector and outlet 2Turn on the projectors power Set the power switch to [ | ] (ON). The projector will go to STANDBY mode and the POWER indicator will light to solid orange. 3Press the STANDBY/ON button (control panel or remote control) • The projector begins warming up and the POWER indicator blinks green. • The POWER indicator stops blinking and lights to solid green once the projectors power is completely on. 4Remove the lens cap The picture is projected. POWER-indikator STANDBY/ON STANDBY/ONLASERBLANK RGBVIDEO TURNING ON THE POWER Control panel Precautions Connect all devices to be used to the projector prior to turning on the power.™ WARNINGWhen the power is ON, a strong light is emitted. Do not look into the lens. Turn the power on/off in right order. • Power on the projector before the computer or video tape recorder. • Power off the projector after the computer or video tape recorder. NOTE på/av-bryter $19&/7 4 1.
RGB 15 6Use the zoom ring to adjust the screen size 7Use the focus ring to focus the picture 5 If selecting RGB input Press the RGB button Press this button to toggle between the devices connected to RGB IN 1 and 2. As illustrated below, each time you press the RGB button, the projector switches between RGB IN 1 and 2. Select the signal you wish to project. If selecting video input Press the VIDEO button Press this button to toggle between the devices connected to VIDEO IN, S- VIDEO IN and COMPONENT VIDEO. As illustrated below, each time you press the VIDEO button, the projector switches between VIDEO IN, S-VIDEO IN and COMPONENT VIDEO. Select the signal you wish to project. Using the remote control Press the INPUT button As illustrated below, each time you press the INPUT button, the projector switches between its input signal ports. Select the signal you wish to project. Using the projectors control panel VIDEO RGB IN 1 RGB IN 2 VIDEO IN S-VIDEO IN COMPONENT VIDEO VIDEO IN S-VIDEO IN COMPONENT VIDEO RGB IN 1 RGB IN 2 INPUT Selecting an Input Signal $19&/7 4 1.
16 STANDBY/ONLASERBLANK RGBVIDEO AUTO MENU ENTER KEYSTONE RESET FREEZE ASPECT ESC MAGNIFY POSITION OFF ONVOLUME MUTE 1Press the STANDBY/ON button (control panel or remote control) The message Power off? will appear on the screen for approximately 5 seconds. 3Check that the POWER indicator stops blinking and lights to solid orange. Switch the power switch to [O] (OFF). 4Confirm that the POWER indicator has gone off and then attach the lens cap. When the projector has completed powering down, the POWER indicator will go off. STANDBY/ON TURNING OFF THE POWER Control panel 2Press the STANDBY/ON button again (control panel or remote control) Press the STANDBY/ON button again while the Power off? message is visible. The projector lamp goes off and starts cooling down. The POWER indicator blinks orange while the lamp cools down. (Pressing the STANDBY/ON button while the POWER indicator is blinking orange has no effect.) The system goes into the STANDBY mode after cooling down and the POWER indicator stops blinking orange and then lights to solid orange. STANDBY/ON • Except in emergencies, follow the above- mentioned procedure for turning power off. NOTE POWER-indikator på/av-bryter $19&/7 4 1.
17 STANDBY/ONLASERBLANK RGBVIDEO AUTO MENU ENTERKEYSTONE RESET FREEZE ASPECT ESC MAGNIFY POSITION OFF ONVOLUME SEARCH MUTE 1Press the VOLUME button As illustrated on the right, a dialog will appear on the screen to aid you in adjusting the volume. 1Press the MUTE button As illustrated on the right, a dialog will appear on the screen indicating that you have muted the sound. Press the VOLUME button to close the dialog. (Even if you dont do anything, the dialog will automatically disappear after a few seconds.) Press the MUTE button again to restore the sound. 2Press the , buttons to adjust the volume Press the VOLUME button again to close the dialog and complete this operation. (Even if you dont do anything, the dialog will automatically disappear after a few seconds.) Press this to increase the volume Press this to decrease the volume VOLUME MUTE AUTO MENU ENTERKEYSTONE RESET FREEZE ASPECT ESC MAGNIFY POSITION OFF ONVOLUME SEARCH MUTE 16 VOLUME 16 VOLUME 16 VOLUME ADJUSTING THE VOLUME TEMPORARILY MUTING THE SOUND $19&/7 4 1.
18 STANDBY/ONLASERBLANK RGBVIDEO AUTO MENU ENTERKEYSTONE RESET FREEZE ASPECT ESC MAGNIFY POSITION OFF ONVOLUME SEARCH MUTE 1Press the POSITION button As illustrated on the right, a dialog will appear on the screen to aid you in adjusting the position. 2Use the , , , buttons to adjust the position When you want to initialize the position, press the RESET button during adjustment. Press the POSITION button again to close the dialog and complete this operation. (Even if you dont do anything, the dialog will automatically disappear after a few seconds.) This function is only available for RGB IN 1/2 input. ADJUSTING THE POSITION POSITION POSITION Control panel $19&/7 4 1.
19 The automatic adjustment operation requires approximately 10 seconds. Also, please note that it may not function correctly with some input signals. NOTE 1 USING THE AUTOMATIC ADJUSTMENT FEATURE Press the AUTO button Horizontal position (H. POSIT), vertical position (V. POSIT), clock phase (H. PHASE) and horizontal size (H. SIZE) are automatically adjusted. Make sure that the application window is set to its maximum size prior to attempting to use this feature. Dark pictures may still be incorrectly adjusted. Use a bright screen when adjusting. The signal type best suited for the respective input signal is selected automatically. This feature is available only if VIDEO is set to AUTO in the INPUT menu. Automatic Adjustment for RGB Input Automatic Adjustment for Video Input STANDBY/ONLASERBLANK RGBVIDEO AUTO MENU ENTER KEYSTONE RESET FREEZE ASPECT ESC MAGNIFY POSITION OFF ONVOLUME SEARCH MUTE AUTO $19&/7 4 1.