Hitachi Cp-X10000 Users Manual

							61
SECURITY menu
This projector is equipped with security functions.
From the SECURITY menu, items shown in the table below can 
be performed.
To use SECURITY menu: User registration is required before 
using the security functions.
Enter the SECURITY menu1.  Use the ▲/▼ buttons on the SECURITY menu to select ENTER PASSWORD and press the ► 
button. The ENTER PASSWORD box will be displayed.  
If you have forgotten your password
1.  While the ENTER PASSWORD box is displayed, press and hold the RESET button on the remote 
control for about 3 seconds or press and hold the COMPUTER button for 3 seconds while pressing 
the ► button on the projector.
2.    The 10 digit Inquiring Code will be displayed. Contact your dealer with the 10 digit Inquiring Code. 
Your password will be sent after your user registration information is confirmed.
• If there is no key input for about 55 seconds while the Inquiring Code is displayed, the menu will 
close. If necessary, repeat the process from 1.  
2.   Use the ▲/▼/◄/► buttons to enter the registered password. 
The factory default password is  9630. This password can be 
changed (
 SECURITY PASSWORD CHANGE). Move the 
cursor to the right side of the ENTER PASSWORD box and 
press the ► button to display the SECURITY menu.
• It is strongly recommended the factory default password to be changed 
as soon as possible.
• If an incorrect password is input, the ENTER PASSWORD box will 
be displayed again. If incorrect password is input 3 times, the projector 
will turn off. Afterwards the projector will turn off every time an incorrect 
password is input.
3.   Items shown in the table below can be performed.
Item Description
SECURITY 
PASSWORD  CHANGE
1   Use the ▲/▼ buttons on the SECURITY menu 
to select SECURITY PASSWORD CHANGE 
and press the ► button to display the ENTER 
NEW PASSWORD box.
2   Use the ▲/▼/◄/► buttons to enter the new 
password.
3   Move the cursor to the right side of the ENTER 
NEW PASSWORD box and press the ► button 
to display the NEW PASSWORD AGAIN box, 
enter the same password again. 
4  
Move the cursor to the right side of the NEW 
PASSWORD AGAIN box and press the ► 
button and the NOTE NEW PASSWORD box 
will be displayed for about 20 seconds, please 
make note of the password during this time.
• Pressing the ENTER button on the remote control or ► button on the 
projector will close the NOTE NEW PASSWORD box.
• Please do not forget your password.
SECURITY menu
(continued on next page) 
						

							62
SECURITY menu
ItemDescription
MyScreen 
PASSWORD
The MyScreen PASSWORD function can be used to prohibit access to the 
MyScreen function and prevent the currently registered MyScreen image 
from being overwritten.
1 Turning on the MyScreen PASSWORD1-1   Use the ▲/▼ buttons on the SECURITY menu 
to select MyScreen PASSWORD and press the 
► button to display the MyScreen PASSWORD 
on/off menu.
1-2   Use the ▲/▼ buttons on the MyScreen 
PASSWORD on/off menu to select ON. 
The ENTER NEW PASSWORD box (small) will 
be displayed.
1-3   Use the ▲/▼/◄/► buttons to enter the 
password. Move the cursor to the right side 
of the ENTER NEW PASSWORD box (small) 
and press the ► button to display the NEW 
PASSWORD AGAIN box, enter the same 
PASSWORD again.
1-4   Move the cursor to the right side of the NEW 
PASSWORD AGAIN box and press the ► 
button to display the NOTE NEW PASSWORD 
box for about 20 seconds, please make note of 
the password during this time. 
• Pressing the ENTER button on the remote control or ► button on the 
projector will return to MyScreen PASSWORD on/off menu.
When a password is set for MyScreen:
• The MyScreen registration function (and menu) will be unavailable.
• The MyScreen Lock menu will be unavailable.
• The START UP setting will be locked on MyScreen (and the menu will be 
unavailable).
Turning the MyScreen PASSWORD off will allow normal operation of these 
functions.
• Please do not forget your MyScreen PASSWORD.2 Turning off the MyScreen PASSWORD2-1   Follow the procedure in 1-1 to display the MyScreen PASSWORD on/off 
menu.
2-2   Select OFF to display the ENTER PASSWORD box (large). Enter the 
registered password and the screen will return to the MyScreen on/of f 
menu.
If an incorrect PASSWORD is input, the menu will close. If necessary, repeat 
the process from 2-1.
3 If you have forgotten your password3-1   Follow the procedure in 1-1 to display the MyScreen PASSWORD on/off 
menu.
3-2  
Select OFF to display the ENTER PASSWORD 
box (large). The 10 digit Inquiring Code will be 
displayed inside the box.
3-3   Contact your dealer with the 10 digit Inquiring 
Code. Your password will be sent after your user 
registration information is confirmed.
ENTER NEW PASSWORD 
box (small)
(continued on next page)
ENTER PASSWORD box  (large) 
						

							63
SECURITY menu
ItemDescription
PIN LOCK
PIN LOCK is a function which prevents the projector from being used unless 
a registered Code is input.
1 Turning on the PIN LOCK1-1   Use the ▲/▼ buttons on the SECURITY menu 
to select PIN LOCK and press the ► button or 
the 
ENTER button to display the PIN LOCK on/
off menu.
1-2   Use the ▲/▼ buttons on the PIN LOCK on/off 
menu to select ON and the Enter PIN Code box 
will be displayed. 
1-3    Input a 4 part PIN code using the ▲/▼/◄/►, 
COMPUTER button. 
The PIN Code again box will appear. Reenter 
the same PIN code. This will complete the PIN 
code registration.
• If there is no key input for about 55 seconds while 
the Enter PIN Code box or the PIN Code again 
box is displayed, the menu will close. If necessary, 
repeat the process from 1-1.
Afterwards, anytime the projector is restarted after 
the power switch is turned off the Enter PIN Code 
box will be displayed. Enter the registered PIN code.
The projector can be used after entering the 
registered PIN code. If an incorrect PIN code is 
input, the Enter PIN code box will be displayed 
again.
If an incorrect PIN Code is input 3 times, the projector will turn of f. 
Afterwards the projector will turn off every time an incorrect PIN code is 
input. The projector will also turn off if there is no key input for about 5 
minutes while the Enter PIN Code box is displayed.
This function will activate only when the projector is started after the power 
switch was turned off.
• Please do not forget your PIN code.
2 Turning off the PIN LOCK
2-1   Follow the procedure in 1-1 to display the PIN LOCK on/off menu. Use 
the ▲/▼ buttons to select OFF and the Enter PIN Code box will be 
displayed. 
Enter the registered PIN code to turn the PIN LOCK function off.
If an incorrect password is input 3 times, the menu will close.
3 If you have forgotten your PIN Code
3-1   While the Enter PIN Code box is displayed, 
press and hold the RESET button for three 
seconds or press and hold the COMPUTER 
button for 3 seconds while pressing the ► 
button on the projector. 
The 10 digit Inquiring Code will be displayed.
• If there is no key input for about 5 minutes while the Inquiring Code is 
displayed, the projector will turn off.
3-2   Contact your dealer with the 10 digit Inquiring Code. Your password will 
be sent after your user registration information is confirmed.
(continued on next page) 
						

							64
SECURITY menu
ItemDescription
TRANSITION  DETECTOR
If this function is set to ON when the vertical angle of 
the projector or mirror setting at which the projector is 
turned on is different than the previously recorded, the 
TRANSITION DETECTOR ON alarm will be displayed 
and the projector will not display the input signal.
• To display the signal again, set this function OFF.• After about 5 minutes of displaying the TRANSITION DETECTOR ON alarm, 
the lamp will turn off.
• Keystone adjustment feature has been prohibited as long as the  Transition 
Detector function is on.
1 Turning on the TRANSITION DETECTOR1-1   Use the ▲/▼ buttons on the SECURITY menu to 
select TRANSITION DETECTOR and press the ► 
or the 
ENTER button to display the TRANSITION 
DETECTOR on/off menu. 
1-2   Use the ▲/▼ buttons on the TRANSITION 
DETECTOR on/off menu to select ON. Select 
ON and the current angle and mirror setting will 
be recorded. The ENTER NEW PASSWORD 
box (small) will be displayed.
1-3 
 Use the ▲/▼/◄/► buttons to enter a password. 
Move the cursor to the right side of the ENTER 
NEW PASSWORD box (small) and press the 
► 
button to display the NEW PASSWORD AGAIN 
box, enter the same password again.
1-4   Move the cursor to the right side of the NEW 
PASSWORD AGAIN box and press the ► 
button to display the NOTE NEW PASSWORD 
box for about 20 seconds, please make note of 
the password during this time.
• Pressing the ENTER button on the remote control or the ► button on 
the projector will return to the TRANSITION DETECTOR on/off menu.
• Please do not forget your TRANSITION DETECTOR password.
• This function will activate only when the projector is started after the power 
switch was turned off.
• 
This feature may not function properly if the projector is not in a stable position 
when ON is selected.
2 Turning off the TRANSITION DETECTOR2-1  Follow the procedure in 1-1 to display the Transition Detector on/off menu.2-2   Select OFF to display the ENTER PASSWORD box (large). Enter the 
registered password and the screen will return to the TRANSITION 
DETECTOR on/off menu.
If an incorrect password is input, the menu will close. If necessary , repeat 
the process from 2-1.
3 If you have forgotten your password3-1  Follow the procedure in 1-1 to display the Transition Detector on/off menu.3-2  Select OFF to display the ENTER PASSWORD box 
(large). The 10 digit Inquiring Code will be displayed 
inside the box.
3-3   Contact your dealer with the 10 digit Inquiring 
Code. Your password will be sent after your 
user registration information is confirmed.
(continued on next page)
ENTER NEW PASSWORD 
box (small)
ENTER PASSWORD box (large) 
						

							65
SECURITY menu
ItemDescription
MY TEXT 
PASSWORD
The MY TEXT PASSWORD function can prevent the MY TEXT from being overwritten.When the password is set for the MY TEXT;• The MY TEXT DISPLAY menu will be unavailable, which can prohibit changing the 
DISPLAY setting.
• The MY TEXT WRITING menu will be unavailable, which can prevent the MY TEXT 
from being overwritten.
1 Turning on the MY TEXT PASSWORD1-1   Use the ▲/▼ buttons on the SECURITY menu 
to select the MY TEXT PASSWORD menu and 
press the ► button to display the MY TEXT 
PASSWORD on/off menu.
1-2   Use the ▲/▼ buttons on the MY TEXT 
PASSWORD menu to select ON. The ENTER 
NEW PASSWORD box (small) will be displayed.
1-3   Use the ▲/▼/◄/► buttons to enter the 
password. Move the cursor to the right side 
of the ENTER NEW PASSWORD box (small) 
and press the ► button to display the NEW 
PASSWORD AGAIN box, and then enter the 
same password again.
1-4   Move the cursor to the right side of the NEW 
PASSWORD AGAIN box and press ► button 
to display the NOTE PASSWORD box for 
about 20 seconds, then please make note of 
the password during this time.
• Pressing the ENTER button on the remote 
control or ► button on the projector will return 
to the MY TEXT PASSWORD on/off menu.
2 Turning off the MY TEXT PASSWORD2-1   Follow the procedure in 1-1 to display the MY 
TEXT PASSWORD on/off menu.
2-2   Select OFF to display the ENTER PASSWORD 
box (large). Enter the registered password 
and the screen will return to the MY TEXT 
PASSWORD on/off menu. 
If an incorrect password is input, the menu will 
close. If necessary, repeat the process from 2-1
3 If you have forgotten your password3-1   Follow the procedure in 1-1 to display the MY TEXT PASSWORD on/off 
menu.
3-2   Select OFF to display the ENTER PASSWORD box (large). The 10 digit 
inquiring code will be displayed inside the box. 
3-3   Contact your dealer with the 10 digit inquiring code. Your password will 
be sent after your user registration information is confirmed.
ENTER NEW PASSWORD 
BOX (small)
ENTER PASSWORD BOX  (large)
(continued on next page) 
						

							66
SECURITY menu
ItemDescription
MY TEXT  DISPLAY
1   Use the ▲/▼ buttons on the SECURITY menu to 
select the MY TEXT DISPLAY menu and press the 
► button to display the MY TEXT DISPLAY on/off 
menu.
2   Use the ▲/▼ buttons on the MY TEXT DISPLAY 
on/off menu to select on or off.
ON 
ó OFFWhen it is set ON, the MY TEXT will be displayed 
on the START UP screen and the INPUT-
INFORMATION- when the INFORMATION on the 
SERVICE menu is chosen.
• This function is available only when the MY TEXT 
PASSWORD function is set to the OFF.
MY TEXT 
WRITING
1   Use the ▲/▼ buttons on the SECURITY menu to 
select the MY TEXT WRITING menu and press 
the ► button. The MY TEXT WRITING dialog will 
be displayed.
2 
 The current MY TEXT will be displayed on the first 3  
lines. If not yet written, the lines will be blank. 
Use the 
▲/▼/◄/► buttons and the ENTER or VIDEO button to select and enter 
characters. The RESET button can be used to erase 1 character at a time. Also if 
you move the cursor to DELETE or ALL CLEAR on screen and push the ENTER 
or VIDEO button, 1 character or all characters will be erased. The MY TEXT can 
be input up to 24 characters on each line.
3   
To change an already inserted character, 
press the ▲/▼ button to move the 
cursor to one of the first 3 lines, and use 
the ◄/► buttons to move the cursor on 
the character to be changed.
After pressing the 
ENTER or VIDEO 
button, the character is selected. 
Then, follow the same procedure as 
described at the item 2 above.
4    To finish entering text, move the cursor 
to the OK on screen and press the 
ENTER or VIDEO button. To revert 
to the previous MY TEXT without 
saving changes, move the cursor to 
the CANCEL on screen and press the 
ENTER or VIDEO button.• The MY TEXT WRITING function 
is available only when the MY TEXT 
PASSWORD function is set to OFF. 
						

							67
Maintenance
Maintenance 
 A worn out lamp bulb could burn or burst. It is recommended to keep a spare 
lamp unit on hand and to replace the lamp unit when the projected image darkens 
or color reproduction becomes poor. 
To prepare the spare, contact your dealer and tell the following type number.
Lamp unit
Type number of the optional lamp unit: DT01001
•The value shown on the OPTION menu as the LAMP TIME is the use 
time that is counted since the last time the LAMP TIME was reset. Refer to the 
value for proper maintenance. NOTE
If the projector is installed in a special state such as ceiling mount, or if the lamp 
bulb has broken, also ask the dealer to replace the lamp unit. Otherwise, follow 
the procedure shown below to replace the lamp.
Make sure that the projector is unplugged and 
cooled down.
 1.
6.
To display the 
ADVANCED MENU , press the MENU button (on the control 
panel or the remote control). On the  EASY MENU, select the “ADVANCED 
MENU” using the ▲/▼ cursor buttons, then press the ► cursor button.
To display the  LAMP TIME dialog, select the 
“LAMP TIME” using the ▲/▼ cursor buttons in 
the right column, then press the ► cursor button.
Use the ► cursor button according to the dialog, 
Selecting “ OK” resets the LAMP TIME  value.
(1)
(2)
(4)
(5)
Turn the projector on.
I    O
HDMI
DVI-D
CONTROL IN CONTROL OUT REMOTE
CONTROL
IN
OUT S-VIDEO
COMPUTER IN2
COMPUTER IN1
VIDEO 1 BNC
R/Cr/Pr G/Y B/Cb/Pb H V VIDEO 2 Y
Cb/Pb Cr/Pr
AC IN LAN
MONITOR
OUT
The lamp cover
The handles
Loosen the screw (marked by arrow) of the 
lamp cover. Then slide and take it off.2.
Loosen the 3 screws (marked by arrow) of the 
lamp unit. Then picking the handles of the unit, 
gently take it from the projector.
 
3.
Gently set the new lamp unit into place. Then 
retighten the screws of the lamp unit.4.
Put the lamp cover back into place, and 
retighten the screw of the lamp cover.
 5.
Reset the LAMP TIME value.
►Be sure to reset the LAMP TIME only when you have replaced the 
lamp unit. NOTICE To select the OPTION menu, select the 
“OPTION” using the ▲/▼ cursor buttons in the 
left column, then press the ► cursor button.
(3) 
						

							68
Maintenance
Lamp warning
 HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE
►The projector uses a high-pressure mercury glass lamp. The 
lamp can break with a loud bang, or burn out, if jolted or scratched, handled 
while hot, or worn over time. Note that each lamp has a different lifetime, and 
some may burst or burn out soon after you start using them. In addition, when 
the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and 
for gas containing mercury to escape from the projector’s vent holes.
►About disposal of a lamp:  This product contains a mercury lamp; do not put 
it in a trash. Dispose of it in accordance with environmental laws.
• For lamp recycling, go to www.lamprecycle.org (in the US).
• For product disposal, contact your local government agency  
or www.eiae.org (in the US) or www.epsc.ca (in Canada).
For more information, call your dealer. WARNING
• If the lamp should break (it will make a loud bang when it does), 
unplug the power cord from the outlet, and make sure to request a 
replacement lamp from your local dealer. Note that shards of glass 
could damage the projector’s internals, or cause injury during handling, 
so please do not try to clean the projector or replace the lamp yourself.
• If the lamp should break (it will make a loud bang when it does), 
ventilate the room well, and make sure not to breathe the gas that 
comes out of the projector vents, or get it in your eyes or mouth.
• Before replacing the lamp, turn the projector off and unplug the power 
cord, then wait at least 45 minutes for the lamp to cool sufficiently
. 
Handling the lamp while hot can cause burns, as well as damaging the 
lamp.
• Never unscrew except the appointed (marked by an arrow) screws.
• Do not open the lamp cover while the projector is suspended from 
a ceiling. This is dangerous, since if the lamp’s bulb has broken, the 
shards will fall out when the cover is opened. In addition, working in 
high places is dangerous, so ask your local dealer to have the lamp 
replaced even if the bulb is not broken.
• Do not use the projector with the lamp cover removed. At the lamp 
replacing, make sure that the screws are screwed in firmly. Loose 
screws could result in damage or injury.
• Use only the lamp of the specified type.
• If the lamp breaks soon after the first time it is used, it is possible 
that there are electrical problems elsewhere besides the lamp. If this 
happens, contact your local dealer or a service representative.
• 
Handle with care: jolting or scratching could cause the lamp bulb to burst during use.• Using the lamp for long periods of time, could cause it to darken, not 
to light up or to burst. When the pictures appear dark, or when the color 
tone is poor, please replace the lamp as soon as possible. Do not use 
old (used) lamps; this is a cause of breakage. 
Disconnect  the plug 
from the  power outlet 
						

							69
Maintenance
Filter coverFilter unit knobs
Intake vents
To keep inside ventilation normal, keep a spare and replace the filter unit 
periodically, although frequent replacement is not needed for this product.
To prepare the spare, contact your dealer and tell the following type number.Type number of the optional filter unit: MU06351
1.Make sure that the projector is 
unplugged and cooled down.
2.Use a vacuum cleaner on 
and around the filter cover.
3.Pick and pull up the filter 
cover knobs to take it off.
4.
5.
Use a vacuum cleaner on and around 
the intake vents of the projector.
6.Set the new filter unit into the place.
Filter unit
Pinch and pull out the filter unit 
knob to take it off.
• The value shown on the EASY menu as the FILTER TIME is the use 
time that is counted since the last time the FILTER TIME was reset. Refer to 
the value for proper maintenance.
• You can utilize the message function, which is set up by the item FILTER 
TIME of the OPTION menu, to notify you when to replace the lamp.  NOTE
►Before checking or replacing the filter unit, turn off, unplug, 
and cool down the projector.
►To keep inside ventilation normal, check and replace the filter unit periodically.
►Use only the manufacturer specified type of the filter unit. ►Be sure to reset the FILTER TIME only when you have replaced 
the filter unit. WARNING
NOTICE
The following walks you through the steps to replace the filter unit.
7.Put the filter cover back into the place.
8.Reset the FILTER TIME value.
Turn the projector on.
To display the FILTER TIME dialog, select the 
“FILTER TIME” using the ▲/▼ cursor buttons, 
then press the ► cursor button.
Use the ► cursor button according to the dialog, 
Selecting “OK” resets the FILTER TIME value.
(1)
(3)
(4)
To display the EASY MENU, press the MENU 
button (on the control panel or the remote 
control). On the ADVANCED MENU, select the 
“EASY MENU” using the ▲/▼ cursor buttons in 
the left column, then press the ► cursor button.
(2)
Filter cover knobs 
						

							70
Maintenance
Internal clock batter y 
►Be careful of handling battery, since a battery can cause explosion, 
cracking or leakage that could result in a fire, an injury, and environment pollution. 
• Use only the specified battery.
• When replacing the battery, replace it with a new battery.
• Do not use a battery with damage, such as scratches, dents, rust or leakage.
• Do not work on a battery; for example recharging or soldering.
• Keep a battery in a dark, cool and dry place. Never expose a battery to a fire or water .
• Keep a battery away from children and pets. Be careful for them not to swallow a 
battery.
• When a battery leaked, wipe the leakage out well with a waste cloth. If the leakage 
adhered to your body, immediately rinse it well with water. When a battery leaked in the 
battery holder, replace the batteries after wiping the leakage out.
• Obey the local laws on disposing a battery.WARNING
This projector is being loaded with a battery for the internal clock that the network 
function needs. When the clock does not work correctly, request your dealer 
to check the battery and to replace if needed. For replacement, prepare a new 
battery of the following type. You can buy it at the store or order it from your 
dealer. HITACHI MAXELL, part number CR2032 or CR2032H
Others 
For the lens
For the inside of the projector
For the cabinet of the projector and remote control Be careful not to scratch, crack, dirty, or fog the lens surface, since it affects the 
image quality. When the lens surface is fogged or dirty, gently wipe it only with the 
commercial cloth or paper lens cleaner.
In order to ensure the safe use of your projector, please have it cleaned and 
inspected by your dealer about once every year.
For the dirty cabinet of the projector or remote control, use soft cloth. Dip a soft 
cloth in water or a neutral cleaner diluted in water, and wipe the cabinet lightly 
after wringing it well. Then, wipe again lightly with a soft and dry cloth.
►Before checking or cleaning the lens, turn off, unplug, and 
cool down the projector.
►Do not scratch the projector and knock it against something. Use special 
caution for the lens surface.
►Do not wet the product. Do not let any liquids enter to the inside. Do not use a 
spray. WARNING
►Do not directly touch the lens surface with hands.
►Do not use cleaners or chemicals other than those specified in this manual. NOTICE