Hitachi Cp-X10000 Users Manual

							21
Operating
Using the functions for the lens
ZOOM / FOCUS
Press the ZOOM / FOCUS button. The ZOOM / FOCUS dialog 
will appear. Adjust the zoom / focus using the ◄/► button while 
the dialog is displayed. Press the ▼ button to select "EXIT" on 
the dialog. It finishes the OSD menu.
LENS SHIFT
Press the LENS SHIFT button. The LENS SHIFT dialog 
will appear. Using the ▲/▼/◄/► buttons while the dialog 
is displayed shifts the lens. 
   
In the LENS SHIFT dialog:  
Press the 
DIGITAL button.
   
In the standby mode:  
Press the LENS SHIFT and the DIGITAL buttons for 3 seconds at the same time.
CENTERING
●  While the lens is shifting, the menu will disappears and the icon of hourglass will 
appears on screen. Shifting may take some time. Depending on the case, it may 
reach one minute.
●    The LENS SHIFT indicator lights up or blinks in green while the lens is shifting. 
Then the indicator will stop blinking and light for 3 seconds in steady green 
when the centering is complete.
●  
When the lens is located in the center already, pressing the DIGITAL button in the 
LENS SHIFT dialog lights in steady green the LENS SHIFT indicator for 3 seconds.
LENS MEMORY SAVE / LOAD / CLEAR
This projector is equipped with memory functions for the lens adjustments (zoom, 
focus and shift).
To display the LENS MEMORY dialog, select the LENS MEMORY on the ZOOM, 
FOCUS or LENS SHIFT dialog. Then the LENS MEMORY dialog will appear.
   
SAVE:To save the current lens adjustments, select 
a SAVE-(1-3) and press ► or 
ENTER button.
  
LOAD:To load a saved adjustments, select the 
LOAD-(1-3) and press ► or 
ENTER button. 
When the 
MY BUTTON button is allocated to 
the LOAD-(1-3) the memory can be loaded 
without the LENS MEMORY dialog.
   
CLEAR:Selecting the CLEAR LENS MEMORY in the LENS MEMORY dialog 
displays CLEAR LENS MEMORY dialog. Select the number to be cleared 
using ▲/▼ buttons and press the ► button. The dialog to check your intention 
will come out. Then press the ► button again in the dialog.
• The adjustable range of ZOOM and FOCUS 
varies depending on the lens unit  mounted on the 
projector to maintain picture quality. Therefore ZOOM or 
FOCUS adjustments may not reach the end of the bar 
indicators in the dialog, and that is not a failure. NOTE 
						

							22
Operating
1.
1.Press the VIDEO button to select an input for video signal.  
Each time you press the button, the projector switches its 
video input port as below. 
Press the 
DIGITAL  button to select an input for digital signal.  
Each time you press the button, the projector switches its 
digital input port as below. 
● While ON is selected for AUTO SEARCH item in OPTION menu, the projector 
will keep checking every port sequentially till an input signal is detected (
47). 
If 
VIDEO button is pushed when COMPUTER IN1 or COMPUTER IN2 port is 
selected, the projector will check Component port first.
● While ON is selected for AUTO SEARCH item in OPTION menu, the projector 
will keep checking every port sequentially till an input signal is detected (
47). 
If 
DIGITAL button is pushed when Component, S-VIDEO, VIDEO 1 or VIDEO 2 
port is selected, the projector will check 
HDMI port first.
COMPONENT (Y, Cb/Pb, Cr/Pr)  S-VIDEO   VIDEO 1  VIDEO 2
HDMI 
 DVI-D 
1.Press the MY SOURCE button on the remote control. The 
input signal will be changed into the signal you set as MY 
SOURCE(
49).
●    This function also can use for document camera. Select the input port that 
connected the document camera. 
BLANK LASER
FREEZE
LASER
INDICATOR
DIGITAL
STANDBY/ON
COMPUTER
LENS SHIFT KEYSTONEID 3
ID 4
ID 2 ID 1VIDEO
AUTO
 ASPECTRESET
MENU
MAGNIFYON
OFF
3
4
ENTER
FOCUS+
-
POSITION
PbyP
ZOOM+
-
1
2
MY BUTTON
MY SOURCE
SHUTTER
Displaying and switching the image
        COMPUTER IN1  
  COMPUTER IN2    BNC 
1.Press the COMPUTER button to select an input port for the 
RGB signal. 
Each time you press the button, the projector switches its 
RGB input port from the current port as below.
●  While ON is selected for AUTO SEARCH item in OPTION menu, the 
projector will keep checking every port sequentially till an input signal is 
detected
 (47). If COMPUTER button is pushed when VIDEO 1, VIDEO 
2, S-VIDEO, Component, HDMI or DVI-D port is selected, the projector will 
check 
COMPUTER IN1 port first. 
BLANK LASER
FREEZE
LASER
INDICATOR
DIGITAL
STANDBY/ON
COMPUTER
LENS SHIFT KEYSTONEID 3
ID 4
ID 2 ID 1VIDEO
AUTO
 ASPECTRESET
MENU
MAGNIFYON
OFF
3
4
ENTER
FOCUS+
-
POSITION
PbyP
ZOOM+
-
1
2
MY BUTTON
MY SOURCE
SHUTTER
BLANK
LASER
FREEZE
LASER
INDICATOR
DIGITAL
STANDBY/ON
COMPUTER
LENS SHIFT KEYSTONEID 3
ID 4
ID 2 ID 1VIDEO
AUTO
 ASPECTRESET
MENU
MAGNIFYON
OFF
3
4
ENTER
FOCUS+
-
POSITION
PbyP
ZOOM+
-
1
2
MY BUTTON
MY SOURCE
SHUTTER
BLANK
LASER
FREEZE
LASER
INDICATOR
DIGITAL
STANDBY/ON
COMPUTER
LENS SHIFT KEYSTONEID 3
ID 4
ID 2 ID 1VIDEO
AUTO
 ASPECTRESET
MENU
MAGNIFYON
OFF
3
4
ENTER
FOCUS+
-
POSITION
PbyP
ZOOM+
-
1
2
MY BUTTON
MY SOURCE
SHUTTER 
						

							23
Operating
1.Press the AUTO button on the remote control.
Pressing this button performs the following.
Using the automatic adjustment feature
   For a computer signal 
The vertical position, the horizontal position and the 
horizontal phase will be automatically adjusted. 
Make sure that the application window is set to its 
maximum size prior to attempting to use this feature. 
A dark picture may still be incorrectly adjusted. Use a 
bright picture when adjusting.
   For a video signal and s-video signal 
The video format best suited for the respective input signal will be selected 
automatically. This function is available only when the AUTO is selected for 
the VIDEO FORMAT item in the INPUT menu (
37). The vertical position 
and horizontal position will be automatically set to the default.
   For a component video signal 
The vertical position, horizontal position and horizontal phase will be 
automatically set to the default.
●    The automatic adjustment operation requires approx. 10 seconds.  Also 
please note that it may not function correctly with some input. When this 
function is performed for a video signal, a certain extra such as a line may 
appear outside a picture.
●    The items adjusted by this function may vary when the FINE or DISABLE is 
selected for the AUTO ADJUST item of the SERVICE item in the OPTION 
menu (
50).
1.Press the ASPECT button on the remote control.   
Each time you press the button, the projector switches the mode for aspect 
ratio in turn. 
Selecting an aspect ratio
● *16:10 / FULL: CP-WX11000 only. NATIVE: Except 
CP-X10000. SMALL: Except CP-WX11000.
● The NORMAL mode keeps the original aspect ratio of 
the signal. 
  
For a computer signal
NORMAL  4:3  16:9  16:10
*               SMALL*  NATIVE*  FULL*
  
For an HDMI or DVI-D signal
NORMAL  4:3   16:9  16:10
*   14:9   SMALL*   NATIVE*   FULL*
  
For a video signal, s-video signal or component video signal
                      4:3  16:9  16:10
*   14:9  SMALL*  NATIVE*  FULL*  
   
For no signal  
4:3 (fixed, except CP-WX11000) / FULL (fixed, 
CP-WX11000)
BLANK LASER
FREEZE
LASER
INDICATOR
DIGITAL
STANDBY/ON
COMPUTER
LENS SHIFT KEYSTONEID 3
ID 4
ID 2 ID 1VIDEO
AUTO
 ASPECTRESET
MENU
MAGNIFYON
OFF
3
4
ENTER
FOCUS+
-
POSITION
PbyP
ZOOM+
-
1
2
MY BUTTON
MY SOURCE
SHUTTERBLANK
LASER
FREEZE
LASER
INDICATOR
DIGITAL
STANDBY/ON
COMPUTER
LENS SHIFT KEYSTONEID 3
ID 4
ID 2 ID 1VIDEO
AUTO
 ASPECTRESET
MENU
MAGNIFYON
OFF
3
4
ENTER
FOCUS+
-
POSITION
PbyP
ZOOM+
-
1
2
MY BUTTON
MY SOURCE
SHUTTER 
						

							24
Operating
1.Press the POSITION button on the remote control when no 
menu is indicated. 
The “POSITION” indication will appear on the screen.
Adjusting the position
2.Use the ▲/▼/◄/► cursor buttons to adjust the picture position.
When you want to reset the operation, press the RESET 
button on the remote control during the operation.
To complete this operation, press the 
POSITION button 
again. Even if you do not do anything, the dialog will 
automatically disappear after a few seconds.
●  
When this function is performed on a video signal, s-video signal or component 
video signal, some image such as an extra-line may appear at outside of the picture.
●  When this function is performing on a Video signal, S-Video signal, or component 
signal of 480i@60 or 576i@50 input the range of this adjustment depends on the 
OVER SCAN in IMAGE menu (
34). It is not possible to adjust when the OVER 
SCAN is set to 10.
1.Press the KEYSTONE button on the remote 
control. A dialog will appear on the screen 
to aid you in correcting the distortion.
Correcting the keystone distortion
2.Use the ▲/▼ cursor buttons to select AUTO or MANUAL 
operation, and press the ► button to perform the following.
●    The adjustable range of this function will vary among inputs. For some input, this 
function may not work well.
●   When V:INVERT or H&V:INVERT is selected to the MIRROR item in the SETUP 
menu, if the projector screen is inclined or angled downward, this function may 
not work correctly.
●   When the zoom adjustment is set to the TELE (telephoto focus), this function 
may be excessive. This function should be used when the zoom adjustment is 
set to the full WIDE (wide-angle focus) whenever possible.
●   When the projector is placed on the level (about ±3°), this function may not work.
●   When the vertical lens shift is not set fully upward (not set fully downward for the 
optional lens type USL-801 only (
51)), this function may not work well.
●  
When the horizontal lens shift is not set to the center, this function may not work well.
● This function will be unavailable when Transition Detector is on (64).
1)  AUTO executes automatic vertical keystone correction. 
2)    MANUAL displays a dialog for keystone correction.  
Use the ▲/▼ cursor buttons to select the direction to 
correct (
 or ) then use the ◄/► buttons for adjustment.
To close the dialog and complete this operation, press the 
KEYSTONE button 
again. Even if you don’t do anything, the dialog will automatically disappear 
after a few seconds.
BLANK LASER
FREEZE
LASER
INDICATOR
DIGITAL
STANDBY/ON
COMPUTER
LENS SHIFT KEYSTONEID 3
ID 4
ID 2 ID 1VIDEO
AUTO
 ASPECTRESET
MENU
MAGNIFYON
OFF
3
4
ENTER
FOCUS+
-
POSITION
PbyP
ZOOM+
-
1
2
MY BUTTON
MY SOURCE
SHUTTERBLANK
LASER
FREEZE
LASER
INDICATOR
DIGITAL
STANDBY/ON
COMPUTER
LENS SHIFT KEYSTONEID 3
ID 4
ID 2 ID 1VIDEO
AUTO
 ASPECTRESET
MENU
MAGNIFYON
OFF
3
4
ENTER
FOCUS+
-
POSITION
PbyP
ZOOM+
-
1
2
MY BUTTON
MY SOURCE
SHUTTER 
						

							25
Operating
• The zoom level can be finely adjusted. Closely watch the screen to 
find the level you want. NOTE
1.Press the ON button of MAGNIFY on the remote control.  
The “MAGNIFY” indication will appear on the screen and 
the projector will go into the MAGNIFY mode. In the Magnify 
mode, the picture will be zoomed. The indication will 
disappear in several seconds with no operation.
Using the magnify feature
2.Use the ▲/▼ cursor buttons to adjust the zoom level. To move the zoom 
area, press the 
POSITION button in the MAGNIFY mode, then use the 
▲/▼/◄/► cursor buttons to move the area. And to finalize the zoom area, 
press the 
POSITION button again.
To exit from the MAGNIFY mode and restore the screen to normal, press the 
OFF button of MAGNIFY on the remote control. 
●    The projector automatically exits from the MAGNIFY mode when the input 
signal is changed or when the display condition is changed. 
●   In the MAGNIFY mode, the keystone distortion condition may vary, it will be 
restored when the projector exits from the MAGNIFY mode.
1.Press the FREEZE button on the remote control.  
The “FREEZE” indication will appear on the screen (however, 
the indication will not appear when the OFF is selected for 
the MESSAGE item in the SCREEN menu (
45)), and the 
projector will go into the FREEZE mode, which the picture is 
frozen.
To exit the FREEZE mode and restore the screen to normal, 
press the 
FREEZE button again. 
Temporarily freezing the screen
●   
The projector automatically exits from the FREEZE mode when some control 
buttons are pressed.
●   If the projector continues projecting a still image for a long time, the LCD 
panel might possibly be burned in. Do not leave the projector in the FREEZE 
mode for too long.
BLANK LASER
FREEZE
LASER
INDICATOR
DIGITAL
STANDBY/ON
COMPUTER
LENS SHIFT KEYSTONEID 3
ID 4
ID 2 ID 1VIDEO
AUTO
 ASPECTRESET
MENU
MAGNIFYON
OFF
3
4
ENTER
FOCUS+
-
POSITION
PbyP
ZOOM+
-
1
2
MY BUTTON
MY SOURCE
SHUTTER
BLANK
LASER
FREEZE
LASER
INDICATOR
DIGITAL
STANDBY/ON
COMPUTER
LENS SHIFT KEYSTONEID 3
ID 4
ID 2 ID 1VIDEO
AUTO
 ASPECTRESET
MENU
MAGNIFYON
OFF
3
4
ENTER
FOCUS+
-
POSITION
PbyP
ZOOM+
-
1
2
MY BUTTON
MY SOURCE
SHUTTER 
						

							26
Operating
1.Press the BLANK button on the remote control.  
The blank screen will be displayed instead of the screen of 
input signal. Please refer to the BLANK item in SCREEN 
menu (
42).
To exit from the blank screen and return to the input signal 
screen, press the 
BLANK button again. 
Temporarily blanking the screen
●  The projector automatically exits from the BLANK mode when some control 
buttons are pressed.
1.Pressing the SHUTTER button closes or opens the mechanical lens shutter. 
The closed shutter blocks the projection light, so that it can black out the 
screen. 
Temporarily shutting the image
●    The SHUTTER indicator on the projector blinks while the shutter is closed.
●   
The projector will turn off  automatically when the time set up by the SHUTTER 
TIMER passes
 (48).
●   When turning the power off with the STANDBY/ON button (20), the lens 
shutter closed opens automatically. If the power supply is stopped while opening 
or closing the lens shutter, the moving of the lens shutter is stopped too. 
However, when turning the projector on, the lens shutter closed or incompletely 
opened opens automatically.
BLANK LASER
FREEZE
LASER
INDICATOR
DIGITAL
STANDBY/ON
COMPUTER
LENS SHIFT KEYSTONEID 3
ID 4
ID 2 ID 1VIDEO
AUTO
 ASPECTRESET
MENU
MAGNIFYON
OFF
3
4
ENTER
FOCUS+
-
POSITION
PbyP
ZOOM+
-
1
2
MY BUTTON
MY SOURCE
SHUTTER
BLANK
LASER
FREEZE
LASER
INDICATOR
DIGITAL
STANDBY/ON
COMPUTER
LENS SHIFT KEYSTONEID 3
ID 4
ID 2 ID 1VIDEO
AUTO
 ASPECTRESET
MENU
MAGNIFYON
OFF
3
4
ENTER
FOCUS+
-
POSITION
PbyP
ZOOM+
-
1
2
MY BUTTON
MY SOURCE
SHUTTER 
						

							27
Operating
Most of operations are effective for the main area 
only. Also the audio input signal paired with the 
picture input signal for the main area is assigned 
as the audio output signal. The main area can be 
changed using the cursor buttons ◄/► when the 
setting information is on the screen.
PbyP (Picture by Picture)
The PbyP is a function to display two different picture signals on a screen that is 
split in two areas for each signal. Some of functions can be used with the same 
operation as it for the normal mode (not in the PbyP mode). There are some 
operations available only in the  PbyP mode.
The setting information is displayed for several 
seconds when the  PbyP function is started. It shows 
the input signal information for each area. Also, there 
will be a yellow frame with one of the area that is the main area where most 
of operations are effective. The information can be displayed using the cursor 
buttons ▲/▼/◄/► when the setting information is not on the screen. Press the 
PbyP button on the 
remote control, then the PbyP 
function will be started. To quit 
the PbyP mode, press the button 
again.
Press the COMPUTER, VIDEO or DIGITAL button 
while in the PbyP mode, the menu to select the 
input signal will be appeared. Choose a signal using 
the cursor buttons ▲/▼. If you want to change the signal in 
the sub area, switch the main area using the cursor buttons 
◄/► first. Displaying the same signal on the both areas is 
not allowed. For other combinations of the input signal, refer 
to the right table. Any combinations marked with X can not be 
selected.
Press the MY BUTTON assigned the PbyP SWAP 
(
49). The position of the both area is exchanged 
without any setting change.
Starting the PbyP
Changing the main area Showing the setting information
Changing the picture input signal
Using the PbyP SWAP function
normal mode PbyP mode
•For some signals, it may not be displayed correctly in the  PbyP mode, 
even if it can be displayed properly in the normal mode. NOTE
main area
sub area
main area
Sub
Main
COMPUTER IN1
COMPUTER IN2BNC
HDMI
DVI-DComponent Scart RGB S-VideoVideo 1
Video 2COMPUTER IN10 0 0 0 0 0 0 0 0COMPUTER IN20 0 0 0 0 0 0 0 0
BNC 0 0 0 0 0 0 0 0 0
HDMI 0 0 0 X0X X X X
DVI-D 0 0 0X0X X X X
Component0 0 0 0 0 0 0 0Scart RGB0 0 0 X X X X XS-Video0 0 0X X0X X XVideo 10 0 0 X X0X X XVideo 20 0 0 X X0X X X
BLANK LASER
FREEZE
LASER
INDICATOR
DIGITAL
STANDBY/ON
COMPUTER
LENS SHIFT KEYSTONEID 3
ID 4
ID 2 ID 1VIDEO
AUTO
 ASPECTRESET
MENU
MAGNIFYON
OFF
3
4
ENTER
FOCUS+
-
POSITION
PbyP
ZOOM+
-
1
2
MY BUTTON
MY SOURCE
SHUTTER
setting information 
						

							28
Operating
BLANKLASER
FREEZE
LASER
INDICATOR
DIGITAL
STANDBY/ON
COMPUTER
LENS SHIFT KEYSTONEID 3
ID 4
ID 2 ID 1VIDEO
AUTO ASPECTRESETMENU
MAGNIFYON
OFF
3
4
ENTER
FOCUS+
-
POSITION
PbyP
ZOOM+
-
1
2
MY BUTTON
MY SOURCE
SHUTTER
BLANK
LASER
FREEZE
LASER
INDICATOR
DIGITAL
STANDBY/ON
COMPUTER
LENS SHIFT KEYSTONEID 3
ID 4
ID 2 ID 1VIDEO
AUTO
 ASPECTRESET
MENU
MAGNIFYON
OFF
3
4
ENTER
FOCUS+
-
POSITION
PbyP
ZOOM+
-
1
2
MY BUTTON
MY SOURCE
SHUTTER
To start the MENU, press the MENU button. The MENU 
you last used (EASY or ADVANCED) will appear. EASY 
MENU has priority to appear just after powered on. To 
finish the MENU, press the 
MENU button again.
If you want to change it to EASY/ADVANCED MENU, 
select the EASY/ADVANCED MENU on the menu. 
Using the menu function
● If you want to move the menu position, use the ▲/▼/◄/► buttons after pressing 
the 
POSITION button.
● Some functions cannot be performed when a certain input port is selected, or 
when a certain input signal is displayed.
● 
When you want to reset the operation, press the RESET button on the remote control 
during the operation. Note that items whose functions are performed simultaneously with 
operation (ex. LANGUAGE, H PHASE etc.) cannot be reset.
● Even if you do not do anything, the dialog will automatically disappear after about 30 seconds.
This projector has the following menus: PICTURE, IMAGE, INPUT, SETUP, SCREEN, OPTION, 
NETWORK, SECURITY and EASY MENU. The EASY MENU consists of functions often used, and 
the other menus are classified into each purpose and brought together as the ADVANCED MENU. 
Each of these menus is operated using the same methods with the ▲/▼/◄/►, 
ENTER and RESET 
buttons. The buttons of the same name on the remote control and on the projector function equally.
Indication in OSD (On Screen Display)
RESET button
ENTER button
MENU button
Cursor buttons
STANDBY/ON
MENU
LENS SHIFT COMPUTER
ZOOMVIDEO
FOCUS DIGITAL
SHUTTER
The meanings of the general words on the OSD are as follows.
Start / finish the menu
NOTE
Indication Meaning
EXITSelecting this word finishes the OSD menu. It's the same as pressing the MENU button.
RETURN Selecting this word returns the menu to the previous menu.
CANCEL or NO Selecting this word cancels the operation in the present menu and 
returns to the previous menu.
OK or YES Selecting this word executes the prepared function or shifts the menu to 
the next menu. 
						

							29
EASY MENU
EASY MENU
From the EASY MENU, items shown in the table 
below can be performed.
Select an item using the ▲/▼ cursor buttons on the 
projector or remote control. Then perform it according 
to the following table.
ItemDescription
ASPECT Using the ◄/► buttons switches the mode for aspect ratio.
See the ASPECT item in IMAGE
 menu
 (
34).
AUTO 
KEYSTONE Using the ► button executes the auto keystone function.
See the AUTO KEYSTONE item in SETUP menu (
40).
 
 KEYSTONE Using the ◄/► buttons corrects the vertical keystone distortion.
See the  KEYSTONE item in SETUP menu (
40).
 
 KEYSTONE Using the ◄/► buttons corrects the horizontal keystone distortion.
See the  KEYSTONE item in SETUP menu (
41).
 PICTURE MODE Using the ◄/► buttons switches the picture mode.
The picture modes are combinations of GAMMA and COLOR 
TEMP settings. Choose a suitable mode according to the projected 
source.
     NORMAL  ó CINEMA 
ó DYNAMIC 
ó BOARD(BLACK)
          DAYTIME  ó WHITEBOARD 
ó BOARD(GREEN)
COLOR TEMP
GAMMA
NORMAL 2 MID 1 DEFAULT
CINEMA 3 LOW 2 DEFAULT
DYNAMIC 1 HIGH 3 DEFAULT
BOARD(BLACK) 4 Hi-BRIGHT-1 4 DEFAULT
BOARD(GREEN) 5 Hi-BRIGHT-2 4 DEFAULT
WHITEBOARD 2 MID 5 DEFAULT
DAYTIME 6 Hi-BRIGHT-3 6 DEFAULT
• When the combination of GAMMA and COLOR TEMP differs 
from pre-assigned modes above, the display on the menu for the 
PICTURE MODE is “CUSTOM”. Please refer to the GAMMA and 
COLOR TEMP (
31, 32) items in PICTURE menu.
• When this function is performed, lines or other distiortions may appear.
(continued on next page) 
						

							30
EASY MENU
ItemDescription
ECO MODE Using the ◄/► buttons turns off/on the eco mode.
See the ECO MODE item in SETUP menu
 (
41).
MIRROR Using the ◄/► buttons switches the mode for mirror status.
See the MIRROR item in SETUP menu
 (
41).
RESET Performing this item resets all of the EASY MENU items except the 
FILTER TIME and LANGUAGE.
A dialog is displayed for confirmation. Selecting the OK using the 
► 
button performs resetting.
FILTER TIME The usage time of the air filter is shown in the menu.
Performing this item resets the filter time which counts usage time 
of the air filter.
A dialog is displayed for confirmation. Selecting the OK using the 
► 
button performs resetting. 
See the FILTER TIME item in OPTION menu
 ( 48).
LANGUAGE
Using the ◄/► buttons changes the display language. 
See the LANGUAGE item in SCREEN menu
 ( 42).
ADVANCED MENUPress the ► or ENTER button to use the menu of PICTURE, 
IMAGE, INPUT, SETUP, SCREEN, OPTION, NETWORK or 
SECURITY.
EXIT Press the 
◄ or ENTER button to finish the OSD menu.