Home
>
Global Garden Products
>
Trimmer
>
Global Garden Products Power Hedge Trimme Eht 606 R Instructions Manual
Global Garden Products Power Hedge Trimme Eht 606 R Instructions Manual
Here you can view all the pages of manual Global Garden Products Power Hedge Trimme Eht 606 R Instructions Manual. The Global Garden Products manuals for Trimmer are available online for free. You can easily download all the documents as PDF.
Page 11
7 8
Page 12
![Page 12
CS
X, &
( ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,, XY
Z, /
%B N
( ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,, XY
[,
/ $6%7 ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,, XY
Y, 9
7
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,, XY
\, #.%(
7 ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,, X]
], 17
9 =
$7^1
$7 ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,, X]
_, E9
7 6
...](http://img.usermanuals.tech/thumb/5593/81264/w300_eht-606-r_d-11.png "Page 12
CS
X, &
( ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,, XY
Z, /
%B N
( ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,, XY
[,
/ $6%7 ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,, XY
Y, 9
7
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,, XY
\, #.%(
7 ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,, X]
], 17
9 =
$7^1
$7 ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,, X]
_, E9
7 6
...")
CS X, & ( ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,, XY Z, / %B N ( ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,, XY [, / $6%7 ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,, XY Y, 9 7 ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,, XY \, #.%( 7 ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,, X] ], 17 9 = $7^1 $7 ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,, X] _, E9 7 6 ...
Page 13
SOMMARIOIT 1. Elementi della macchina ...................................... 62 2. Dati tecnici ............................................................ 62 3. Campo di impiego ................................................ 62 4. Avvertenze di sicurezza ....................................... 62 5. Connessione ........................................................ 64 6. Interruttore Inserimento/Disinserimento .............. 64 7. Rotazione impugnatura ........................................ 64 8....
Page 14
30 EHT 606 R Please read these operating instructions carefully before using the tool for the first time and keep them with the tool at all times OPERATINGCONTROLS FIG. 11. Cutting blade 2. Front handle guard 3. Front handle switch lever 4. Ventilation slots 5. Rear handle with start/stop switch 6. Mains plug 7. Blade guard 8. User manual 9. Rotational Handle Button TECHNICAL DATA SAFETYINSTRUCTIONS GENERAL SAFETY RULES Warning! Read all instructions. Failure to follow all instructions listed below may...
Page 15
31 operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication.A moment of inattention while operating power tools may result in serious personal injury. b) Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. c) Avoid accidental starting. Ensure the switch is in the OFF position before...
Page 16
32 EHT 606 R POWER CONNECTION This tool is double insulated; therefore no earth wire is required. The mains voltage must conform to the specifications on the tool rating plate. Cord Sets - Make sure your cord set is in good condition. When using a cord set, be sure to use a cord that is heavy enough to carry the current that your unit wilI draw. An undersized cord set will cause a drop in line voltage resulting in reduced power and overheating. The table (below) shows the correct size to use...
Page 17
33 MAINTENANCE ANDSERVICING Remove the plug from the socket before adjusting or servicing the tool. Wipe down the housing with a damp cloth only and then dry well. Do not use solvents and do not wet the equipment with water: Never use high pressure or steam jet device to clean the unit Always keep the vent slits free. After each use or prolonged use, now and again carefully clean the cutter bar; rub over with an oily cloth or treat with a metal-care spray (Fig. 3). Always retighten loose screws and...
Page 18
102 EHT 606 R note __________________________________ ___________________________________ ___________________________________ __________________________________ __________________________________ _________________________________ __________________________________ _____________________________________________ ___________________________________ ___________________________________ __________________________________ __________________________________ _________________________________...
Page 19
103 note __________________________________ ___________________________________ ___________________________________ __________________________________ __________________________________ _________________________________ __________________________________ _____________________________________________ ___________________________________ ___________________________________ __________________________________ __________________________________ _________________________________...
Page 20
GGP ITALY SPA Via del Lavoro, 6 I-31033 Castelfranco Veneto (TV) B01653-00 Rev.00_10-2006