Global Garden Products Brush Cutter BJ 250 BJ 250D Instructions Manual

31
In order to ensure correct and safe
use of the brush cutter, the assembly instruc-
tions for protection and safety components
must be followed meticulously. The manufac-
turer shall not be held liable if the brush cutter
is used without the aforementioned protection
and safety devices.
CUTTING TOOLS
The use of cutting tools other than the 2-line
heads or metal disks may cause premature
wear or damage to the brush cutter.
METAL DISKS (Fig. 4)
a)Put on a pair of protective gloves before
touching the...

32
RECOMMENDED FUELS
Some conventional petrols are mixed with oxyge-
nating agents such as alcohol, ether compounds,
or other products suitable to reduce air pollution.
Your engine has been designed to run with any
petrol for motor propulsion, including oxygenated
petrols.
Use unleaded fuel.
Engine oil.
Only use top quality synthetic oil for 2-stroke engi-
nes.
Your dealer stocks high quality oils specifically
designed to guarantee a high level of protection to
mechanical parts and maximize engine...

33
Start the engine with the brush cutter in a flat
and stable position.
STARTING UP ( WITH ENGINE COLD )
–(fig. 8) set to“START” the stop switch located
on the handgrip housing the throttle lever. 
–(fig. 9)While pulling the safety lever (ref.1)and
the throttle lever (ref. 2), press the THROTTLE
LOCKOUT BUTTON (ref. 3). While keeping
the throttle lockout button  pressed, release the
throttle lever until it is locked. This operation
enables to pre-accelerate the carburettor.      
Warning: do not touch...

34
CUTTING INSTRUCTIONS
FURTHER SAFETY PRECAUTIONS
Before using the brush cutter re-read all the safety
instructions in this manual. 
WARNING / PRECAUTIONS
–IF YOU ARE NOT FAMILIAR with use of the
brush cutter, practise the procedures with the
engine switched off and the switch in the OFF
“STOP” position.
–ALWAYS FREE THE WORK AREA of objects
such as cans, bottles, stones, etc.. Hitting these
objects can cause serious injury to the operator
or others present and damage the brush cutter.
If you...

35
GB
to eliminate unwanted vegetation from fields,
for easy preparation of the garden or to clear a
particular area of the garden completely.
NOTE:Even with the guard fitted, cutting
around pavements, foundations, walls, etc. can
cause above average wear on the line.
CUT / MOVEMENT
Walk at a regular pace, with a side to side
movement, similar to traditional scything. Do
not tilt the line head during operation. Try
cutting a small area at the correct height. Keep
the line head at a constant distance from...

36
Put on a pair of gloves before sharpening to
avoid contact with the blade. 
Danger of serious wounds.
–AIR FILTER (Fig. 26)
PRECAUTIONS: Never operate the brush cut-
ter without the air filter. The air filter must be
kept clean. If damaged or worn fit a new filter.
To clean the filter (Fig. 26).
1. Press the tab (A)and unscrew (clockwise).
Remove the filter cover, then remove the air
filter  from the filter base.
2. Wash the filter element with soap and water.
DO NOT USE PETROL! 
3. Leave the filter...

37
GB
ALL OUR MACHINES ARE TOP QUALITY. THEY ARE PERFECTLY TUNED AND ARE DESIGNED SO THAT
THE OPERATOR CAN WORK IN MAXIMUM SAFETY.
–NEVER TAMPER WITH MACHINES
–NEVER WORK WITH MACHINES WITH MISSING OR DAMAGED PARTS.
–Do not cause disturbance to the natural environment and those around you.
–Always work in safety.
–Avoid hazardous situations.
–Never work alone, especially in remote areas.
–Take care over those around you and possible dangers. 
–Always wear personal protective garments.
–Only work with...

38
GB
Incorrect start-up procedure
Incorrect carburation
Spark plug dirty
Fuel filter clogged
Dirty air filter
Incorrect carburetion
Incorrect carburetion
Incorrect spark plug gap
Incorrect carburetion
Mixture with incorrect petrol-oil ratio
TROUBLESHOOTING 
The machine will not
start up or keeps
stopping
PROBLEMPROBABLE CAUSE CORRECTIVE MEASURE
Follow the instructions in the User
Manual.
Have the carburettor adjusted at an
Authorised Service Centre.
Clean, correct the gap or replace spark
plug.
Replace...

TECHNICAL DATA
2 -stroke
air-cooled
25.4 cm
3
0.8 kW
10.300 rpm
2.900 rpm
7400 rpm
Fixed Ø 25.4 mm
Centrifugal
LD L8RTF
Electronic
WYJ 398
Petrol – oil 50:1
600 cm
3
Motor type
Displacement
Power
Maximum revolution speed
Idle speed
Tool Maximum revolution speed
Drive
Clutch
Spark plug
Ignition
Carburettor
Mixture
Tank capacity
(m/s
2)
ISO7916
Weight (Kg)* (ISO 11806)
BJ250 - 250D
With fixed shaft  Model
sx1
dx2
sx1
dx2
sx1
dx2
Minimum
revolutions
thread
disk
thread
disk
Mono Duplex
109 dB 108.4 dB
111.5...

Dec. BJ_cod. 171501019_0  01/02/05  17:07  Pagina 40