Gigabyte Ga8knxp Manual

							- 47 -BIOS SetupEnglishOnboard Serial Port 2AutoBIOS will automatically setup the port 2 address.3F8/IRQ4Enable onboard Serial port 2 and address is 3F8.2F8/IRQ3Enable onboard Serial port 2 and address is 2F8. (Default value)3E8/IRQ4Enable onboard Serial port 2 and address is 3E8.2E8/IRQ3Enable onboard Serial port 2 and address is 2E8.DisabledDisable onboard Serial port 2.UART Mode Select
This item allows you to determine which Infra Red(IR) function of Onboard I/O chip.ASKIRSet onboard I/O chip UART to ASKIR Mode.IrDASet onboard I/O chip UART to IrDA Mode.NormalSet onboard I/O chip UART to Normal Mode. (Default Value)UR2 Duplex Mode
This feature allows you to seclect IR mode.
This function will available when UART Mode Select doesnt set at Normal.HalfIR Function Duplex Half. (Default value)FullIR Function Duplex Full.Onboard Parallel port
This feature allows you to select from a given set of parameters if the parallel port uses the onboard
I/O controller.DisabledDisable onboard LPT port.378/IRQ7Enable onboard LPT port and address is 378/IRQ7. (Default value)278/IRQ5Enable onboard LPT port and address is 278/IRQ5.3BC/IRQ7Enable onboard LPT port and address is 3BC/IRQ7.Parallel Port Mode
This feature allows you to connect with an advanced printer via the port mode it supports.SPPUsing Parallel port as Standard Parallel Port. (Default value)EPPUsing Parallel port as Enhanced Parallel Port.ECPUsing Parallel port as Extended Capabilities Port.ECP+EPPUsing Parallel port as ECP & EPP mode.ECP Mode Use DMA
This feature allows you to select Direct Memory Access(DMA) channel if the ECP mode selected.
This function will available when Parallel Port Mode set at ECP or ECP+EPP.3Set ECP Mode Use DMA to 3. (Default value)1Set ECP Mode Use DMA to 1. 
						

							- 48 - GA-8KNXP Ultra-64 MotherboardEnglishGame Port Address201Set Game Port Address to 201. (Default value)209Set Game Port Address to 209.DisabledDisable this function.Midi Port Address300Set Midi Port Address to 300.330Set Midi Port Address to 330.DisabledDisable this function. (Default value)Midi Port IRQ5Set Midi Port IRQ to 5.10Set Midi Port IRQ to 10. (Default value)CIR Port Address310Set CIR Port Address to 310.320Set CIR Port Address to 320.DisabledDisable this function. (Default value)CIR Port IRQ5Set CIR Port IRQ to 5.11 1Set CIR Port IRQ to 11. (Default value) 
						

							- 49 -BIOS SetupEnglishPower Management SetupCMOS Setup Utility-Copyright (C) 1984-2004 Award Software
Power Management SetupACPI Suspend Type[S1(POS)]
Power LED in S1 state[Blinking]
Off by Power button[Instant-off]
PME Event Wake Up[Enabled]
ModemRingOn/WakeOnLan[Enabled]
Resume by Alarm[Disabled]
xDate (of Month) AlarmEveryday
xTime (hh:mm:ss) Alarm0 : 0 : 0
Power On by Mouse[Disabled]
Power On by Keyboard[Disabled]
xKB Power ON PasswordEnter
AC Back Function[Soft-Off]higf: MoveEnter: Select+/-/PU/PD: ValueF10: SaveESC: ExitF1: General Help
F5: Previous ValuesF6: Fail-Save DefaultF7: Optimized DefaultsItem Help
Menu Level}
[S1]
Set suspend type to
Power On Suspend under
ACPI OS
[S3]
Set suspend type to
Suspend to RAM under
ACPI OSACPI Suspend TypeS1(POS)Set ACPI suspend type to S1. (Default value)S3(STR)Set ACPI suspend type to S3.Power LED in S1 stateBlinkingIn standby mode(S1), power LED will blink. (Default value)Dual/OFFIn standby mode(S1):
a. If use single color LED, power LED will turn off.
b. If use dual color LED, power LED will turn to another color.Off by Power buttonInstant-offPress power button then Power off instantly. (Default value)Delay 4 Sec.Press power button 4 sec. to Power off. Enter suspend if button is pressed
less than 4 sec.PME Event Wake UpDisabledDisable this function.EnabledEnable PME Event Wake up. (Default value)ModemRingOn/WakeOnLAN
An incoming call via modem can awake the system from any suspend state or an input signal
comes from the other client server on the LAN can awake the system from any suspend state.DisabledDisable Modem Ring on/wake on Lan  function.EnabledEnable Modem Ring on/wake on Lan. (Default value) 
						

							- 50 - GA-8KNXP Ultra-64 MotherboardEnglishResume by Alarm
You can set Resume by Alarm item to enabled and key in Data/time to power on system.DisabledDisable this function. (Default value)EnabledEnable alarm function to POWER ON system.
If RTC Alarm Lead To Power On is Enabled.
Date (of Month) Alarm : Everyday, 1~31
Time (hh: mm: ss) Alarm : (0~23) : (0~59) : (0~59)Power On By MouseDisabledDisabled this function. (Default value)Mouse ClickDouble click on PS/2 mouse left button to power on the system.Power On By Keyboard
This feature allows you to set the method for powering-on the system.
The option Password allows you to set up to 5 alphanumeric characters to power-on the system.
The option Keyboard 98 allows you to use the standard keyboard 98 to power on the system.PasswordEnter from 1 to 5 characters to set the Keyboard Power On Password.DisabledDisabled this function. (Default value)Keyboard 98If your keyboard have POWER Key button, you can press the key to
power on the system.KB Power ON Password
When Power On by Keyboard set at Password, you can set the password here.EnterInput password (from 1 to 5 characters) and press Enter to set the Keyboard
Power On password.AC BACK FunctionSoft-OffWhen AC-power back to the system, the system will be in Off state.
(Default value)Full-OnWhen AC-power back to the system, the system always in On state.MemoryWhen AC-power back to the system, the system will return to the Last state
before AC-power off. 
						

							- 51 -BIOS SetupEnglishPnP/PCI ConfigurationsPCI 1 IRQ AssignmentAutoAuto assign IRQ to PCI 1. (Default value)3,4,5,7,9,10,11,12,14,15Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 1.PCI 2 IRQ AssignmentAutoAuto assign IRQ to PCI 2. (Default value)3,4,5,7,9,10,11,12,14,15Set IRQ 3,4,5,7,9,10,11,12,14,15 to  PCI 2.PCI 3 IRQ AssignmentAutoAuto assign IRQ to PCI 3. (Default value)3,4,5,7,9,10,11,12,14,15Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 3.CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
PnP/PCI ConfigurationsPCI 1 IRQ Assignment[Auto]
PCI 2 IRQ Assignment[Auto]
PCI 3 IRQ Assignment[Auto]higf: MoveEnter: Select+/-/PU/PD: ValueF10: SaveESC: ExitF1: General Help
F5: Previous ValuesF6: Fail-Save DefaultF7: Optimized DefaultsItem Help
Menu Level}
Device(s) using this
INT:
RAID Cntrlr
- Bus 0 Dev31 Func 2
Network Cntrlr
- Bus 2 Dev 1 Func 0 
						

							- 52 - GA-8KNXP Ultra-64 MotherboardEnglishReset Case Open StatusCase Opened
If the case is closed, Case Opened will show No.
If the case have been opened, Case Opened will show Yes.
If you want to reset Case Opened value, set Reset Case Open Status toEnabled and save
CMOS, your computer will restart.Current Voltage (V) Vcore / DDR25V / +3.3V / +5V / +12VDetect systems voltage status automatically.Current CPU TemperatureDetect CPU Temp. automatically. .Current CPU/POWER/SYSTEM FAN Speed (RPM)Detect CPU/POWER/SYSTEM Fan speed status automatically.CPU Warning Temperature60o
C / 140o
FMonitor CPU Temp. at 60o
C / 140o
F.70o
C / 158o
FMonitor CPU Temp. at 70o
C / 158o
F.80o
C / 176o
FMonitor CPU Temp. at 80o
C / 176o
F.90o
C / 194o
FMonitor CPU Temp. at 90o
C / 194o
F.DisabledDisable this function. (Default value) PC Health StatusCMOS Setup Utility-Copyright (C) 1984-2004 Award Software
PC Health StatusReset Case Open Status[Disabled]
Case OpenedYes
VcoreOK
DDR25VOK
+3.3VOK
+5VOK
+12VOK
Current CPU Temperature33o
C
Current CPU FAN Speed4687 RPM
Current POWER FAN Speed0      RPM
Current SYSTEM FAN Speed0      RPM
CPU Warning Temperature[Disabled]
CPU FAN Fail Warning[Disabled]
POWER FAN Fail Warning[Disabled]
SYSTEM FAN Fail Warning[Disabled]
CPU Smart FAN Control[Enabled]higf: MoveEnter: Select+/-/PU/PD: ValueF10: SaveESC: ExitF1: General Help
F5: Previous ValuesF6: Fail-Save DefaultF7: Optimized DefaultsItem Help
Menu Level}
[Disabled]
Dont monitor
current fan speed
[Enabled]
Clear case open status
and set to be Disabled
at next boot 
						

							- 53 -BIOS SetupEnglishCPU FAN Fail WarningDisabledFan Warning Function Disable. (Default value)EnabledFan Warning Function Enable.POWER FAN Fail WarningDisabledFan Warning Function Disable. (Default value)EnabledFan Warning Function Enable.SYSTEM FAN Fail WarningDisabledFan Warning Function Disable. (Default value)EnabledFan Warning Function Enable.CPU Smart FAN ControlDisabledDisable this function.EnabledEnable CPU Smart Fan control function.(Default value)
a.When the CPU temperature is higher than 60 degrees Celsius, CPU fan
will run at full speed.
b.When the CPU temperature is between 50 and 60 degrees Celsius,
CPU fan will run at high speed.
c.When the CPU temperature is between 40 and 50 degrees Celsius,
CPU fan will run at medium speed.
d.When the CPU temperature is lower than 40 degrees Celsius, CPU fan
will run at low speed. 
						

							- 54 - GA-8KNXP Ultra-64 MotherboardEnglishFrequency/Voltage ControlCPU Clock Ratio
This option will not be shown or not be available if you are using a CPU with the locked ratio.15X~21XIt depends on CPU Clock Ratio.
This setup option will automatically assign by CPU detection.
For C-Stepping P4: 8X,10X~24X default: 15X
For Northwood CPU: 12X~24X default: 16X
The option will display Locked and read only if the CPU ratio is not changeable.CPU Host Clock Control
Note: If system hangs up before enter CMOS setup utility, wait for 20 sec for times out reboot.
        When time out occur, system will reset and run at CPU default Host clock at next boot.DisabledDisable CPU Host Clock Control. (Default value)EnabledEnable CPU Host  Clock Control.CPU Host Frequency (Mhz)100MHz ~ 355MHzSet CPU Host Clock from 100MHz  to 355MHz.
If you use FSB400 Pentium 4 processor, please set CPU Clock to 100MHz.If you use FSB533
Pentium 4 processor, please set CPU Clock to 133MHz. If you use FSB800Pentium 4
processor, please set CPU Clock to 200MHz.
Incorrect using it may cause your system broken. For power End-User use only! øThose items will be available when CPU Host Clock Control is set to Enabled.CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
Frequency/Voltage ControlCPU Clock Ratio[15X]
CPU Host Clock Control[Disabled]
øCPU Host Frequency (Mhz)100
øAGP/PCI/SRC Fixed66/33/100
Memory Frequency For[Auto]
Memory Frequency (Mhz)266
AGP/PCI/SRC Frequency (Mhz)66/33/100
DIMM OverVoltage Control[Normal]
AGP OverVoltage Control[Normal]
CPU Voltage Control[Normal]
Normal CPU Vcore1.750Vhigf: MoveEnter: Select+/-/PU/PD: ValueF10: SaveESC: ExitF1: General Help
F5: Previous ValuesF6: Fail-Save DefaultF7: Optimized DefaultsItem Help
Menu Level} 
						

							- 55 -BIOS SetupEnglishAGP/PCI/SRC Fixed
Serial ATA device is very sensitive to SRC clock. SRC over clock may make Serial ATA device
function cant work properly.Adjust AGP/PCI/SRC clock asychrohous with CPU.Memory Frequency For
for FSB(Front Side Bus) frequency=400MHz,2.66Memory Frequency = Host clock X 2.66.AutoSet Memory frequency by DRAM SPD data. (Default value)
 for FSB(Front Side Bus) frequency=533MHz,2.0Memory Frequency = Host clock X 2.0.2.5Memory Frequency = Host clock X 2.5.AutoSet Memory frequency by DRAM SPD data. (Default value)
for FSB(Front Side Bus) frequency=800MHz,2.0Memory Frequency = Host clock X 2.0.1.6Memory Frequency = Host clock X 1.6.1.33Memory Frequency = Host clock X 1.33.AutoSet Memory frequency by DRAM SPD data. (Default value)Memory Frequency (Mhz)The values depend on CPU Host Frequency(Mhz).AGP/PCI/SRC Frequency (Mhz)The values depend on Fixed AGP/PCI/SRC Frequency.DIMM OverVoltage ControlNormalSet DIMM OverVoltage Control to Normal. (Default value)+0.1VSet DIMM OverVoltage Control to +0.1V.+0.2VSet DIMM OverVoltage Control to +0.2V.+0.3VSet DIMM OverVoltage Control to +0.3V.Incorrect using it may cause your system broken. For power End-User use only!AGP OverVoltage ControlNormalSet AGP OverVoltage Control to Normal. (Default value)+0.1VSet AGP OverVoltage Control to +0.1V.+0.2VSet AGP OverVoltage Control to +0.2V.+0.3VSet AGP OverVoltage Control to +0.3V.Incorrect using it may cause your system broken. For power End-User use only! 
						

							- 56 - GA-8KNXP Ultra-64 MotherboardEnglishCPU OverVoltage ControlSupports adjustable CPU Vcore from 0.8375V to 1.7600V.
    (Default value: Normal)Normal CPU VcoreDisplay your CPU Vcore Voltage.CMOS Setup Utility-Copyright (C) 1984-2004 Award Software}Standard CMOS Features
}Advanced BIOS Features
}Integrated Peripherals
}Power Management Setup
}PnP/PCI Configurations
}PC Health Status
}Frequency/Voltage ControlESC: Quithigf: Select Item
F8: Dual BIOS/Q-FlashF10: Save & Exit SetupLoad Fail-Safe DefaultsLoad Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving Load Fail-Safe Defaults
Fail-Safe defaults contain the most appropriate values of the system parameters that allow
minimum system performance.Load Fail-Safe Defaults (Y/N)? N