GIGABYTE Ga8ipe1000 User Manual

							BIOS Setup - 31 -
English„ „„ „
„Load Optimized Defaults
Optimized Defaults indicates the value of the system parameters which the system would be in best
performance configuration.
„ „„ „
„Set Supervisor Password
Change, set, or disable password. It allows you to limit access to the system and Setup, or just to Setup.
„ „„ „
„Set User Password
Change, set, or disable password. It allows you to limit access to the system.
„ „„ „
„Save & Exit Setup
Save CMOS value settings to CMOS and exit setup.
„ „„ „
„Exit Without Saving
Abandon all CMOS value changes and exit setup. 
						

							GA-8IPE1000 Series Motherboard - 32 -
English
2-1 Standard CMOS Features
Date
The date format is , , , .
Week The week, from Sun to Sat, determined by the BIOS and is display only
Month The month, Jan. Through Dec.
Day The day, from 1 to 31 (or the maximum allowed in the month)
Year The year, from 1999 through 2098
Time
The times format in   . The time is calculated base on the 24-hour military-
time clock. For example, 1 p.m. is 13:00:00.
IDE Channel 0 Master, Slave / IDE Channel 1 Master, Slave
IDE HDD Auto-Detection Press Enter to select this option for automatic device detection.
IDE Channel 0/1 Master/Slave IDE Device Setup.  You can use one of three methods:
• Auto Allows BIOS to automatically detect IDE devices during POST. (Default value)
• None Select this if no IDE devices are used and the system will skip the automatic
detection step and allow for faster system start up.
• Manual User can manually input the correct settings.
Access Mode Use this to set the access mode for the hard drive. The four options are:
CHS/LBA/Large/Auto(default:Auto)
Hard drive information should be labeled on the outside drive casing.  Enter the appropriate option
based on this information.
Cylinder Number of cylinders
Head Number of heads
Precomp Write precomp
Landing Zone Landing zone
Sector Number of sectors
If a hard disk has not been installed, select NONE and press .
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
Standard CMOS Features
Date (mm:dd:yy)Tue, Oct  26  2004
Time (hh:mm:ss)22:31:24
`IDE Channel 0 Master [None]
`IDE Channel 0 Slave [None]
`IDE Channel 1 Master [None]
`IDE Channel 1 Slave [None]
Drive A[1.44M, 3.5]
Drive B [None]
Floppy 3 Mode Suport[Disabled]
Halt On [All, But Keyboard]
Base Memory 640K
Extended Memory 239M
Total Memory 240M
KLJI: Move Enter: Select +/-/PU/PD: ValueF10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-Save Defaults F7: Optimized Defaults
Item Help
Menu Level`
Change the day, month,
year

Sun. to Sat.

Jan. to Dec.

1 to 31 (or maximum
allowed in the month)

1999 to 2098 
						

							BIOS Setup - 33 -
EnglishDrive A / Drive B
The category identifies the types of floppy disk drive A or drive B that has been installed in the computer.
None No floppy drive installed
360K, 5.25 5.25 inch PC-type standard drive; 360K byte capacity.
1.2M, 5.25 5.25 inch AT-type high-density drive; 1.2M byte capacity
(3.5 inch when 3 Mode is Enabled).
720K, 3.5 3.5 inch double-sided drive; 720K byte capacity
1.44M, 3.5 3.5 inch double-sided drive; 1.44M byte capacity.
2.88M, 3.5 3.5 inch double-sided drive; 2.88M byte capacity.
Floppy 3 Mode Support (for Japan Area)
Disabled Normal Floppy Drive. (Default value)
Drive A Drive A is 3 mode Floppy Drive.
Drive B Drive B is 3 mode Floppy Drive.
Both Drive A & B are 3 mode Floppy Drives.
Halt on
The category determines whether the computer will stop if an error is detected during power up.
No Errors The system boot will not stop for any error that may be detected and  you
will be prompted.
All Errors Whenever the BIOS detects a non-fatal error the system will be stopped.
All, But Keyboard The system boot will not stop for a keyboard error; it will stop for all other
errors. (Default value)
All, But Diskette The system boot will not stop for a disk error; it will stop for all other errors.
All, But Disk/Key The system boot will not stop for a keyboard or disk error; it will stop for all
other errors.
Memory
The category is display-only which is determined by POST (Power On Self Test) of the BIOS.
Base Memory
The POST of the BIOS will determine the amount of base (or conventional) memory installed in the
system.
The value of the base memory is typically 512K for systems with 512K memory installed on the
motherboard, or 640K for systems with 640K or more memory installed on the motherboard.
Extended Memory
The BIOS determines how much extended memory is present during the POST.
This is the amount of memory located above 1 MB in the CPUs memory address map.
Total Memory
This item displays the memory size that used. 
						

							GA-8IPE1000 Series Motherboard - 34 -
English
2-2 Advanced BIOS Features
Hard Disk Boot Priority
Select boot sequence for onboard(or add-on cards) SCSI, RAID, etc.
Use <
> or  to select a device, then press to move it up, or  to move it down the list. Press
 to exit this menu.
First / Second / Third Boot Device
Floppy Select your boot device priority by Floppy.
LS120 Select your boot device priority by LS120.
Hard Disk Select your boot device priority by Hard Disk.
CDROM Select your boot device priority by CDROM.
ZIP Select your boot device priority by ZIP.
USB-FDD Select your boot device priority by USB-FDD.
USB-ZIP Select your boot device priority by USB-ZIP.
USB-CDROM Select your boot device priority by USB-CDROM.
USB-HDD Select your boot device priority by USB-HDD.
LAN Select your boot device priority by LAN.
Disabled Select your boot device priority by Disabled.
Password Check
SetupThe system will boot but will not access to Setup page if the correct password is
not entered at the prompt. (Default value)
System The system will not boot and will not access to Setup page if the correct
password is not entered at the prompt.
CPU Hyper-Threading
Enabled Enables CPU Hyper Threading Feature. This feature is only working for
operating system with multi-processors mode supported. (Default value)
Disabled Disables CPU Hyper Threading. #  System will detect automatically and show up when you install the Intel
® Pentium® 4
processor with HT Technology.
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
Advanced BIOS Features
`Hard Disk Boot Priority [Press Enter]
First Boot Device[Floppy]
Second Boot Device [Hard Disk]
Third Boot Device [CDROM]
Password Check[Setup]
# CPU Hyper-Threading [Enabled]
KLJI: Move Enter: Select +/-/PU/PD: ValueF10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-Save Defaults F7: Optimized Defaults
Item Help
Menu Level`
Select Hard Disk Boot
Device Priority 
						

							BIOS Setup - 35 -
English2-3 Integrated Peripherals
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
Integrated Peripherals
On-Chip Primary PCI IDE [Enabled]
On-Chip Secondary PCI IDE [Enabled]
On-Chip SATA[Auto]
x SATA Port0 configure as SATA Port0
SATA Port1 configure as SATA Port1
USB Controller[Enabled]
USB 2.0 Controller[Enabled]
USB Keyboard Support[Disabled]
USB Mouse Support[Disabled]
AC97 Audio[Auto]
Onboard H/W LAN 12[Enabled]
Onboard LAN Boot ROM 12[Disabled]
Onboard Serial Port 1 [3F8/IRQ4]
Onboard Serial Port 2 [2F8/IRQ3]
UART Mode Select [Normal]
x UR2 Duplex  ModeHalf
x TxD, RxD Polarity ActiveLo, Hi
x Use IR Pins IR-Rx2Tx2
Onboard Parallel Port [378/IRQ7]
KLJI: Move Enter: Select +/-/PU/PD: ValueF10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-Save Defaults F7: Optimized Defaults
Item Help
Menu Level`
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
Integrated Peripherals
KLJI: Move Enter: Select +/-/PU/PD: ValueF10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-Save Defaults F7: Optimized Defaults
Item Help
Menu Level`
On-Chip Primary PCI IDE
Enabled Enable onboard 1st channel IDE port. (Default value)
Disabled Disable onboard 1st channel IDE port.
On-Chip Secondary PCI IDE
Enabled Enable onboard 2nd channel IDE port. (Default value)
Disabled Disable onboard 2nd channel IDE port.
Parallel Port Mode [PRINTER]
x ECP Mode Use DMA 3
Game Port Address [201]
Midi Port Address [Disabled]
x Midi Port IRQ 10
Only for GA-8IPE1000-G.
Only for GA-8IPE1000-L. 
						

							GA-8IPE1000 Series Motherboard - 36 -
English
On-Chip SATA
Disabled Disable onboard Seria ATA function.
Auto When there is no device to be plugged in IDE1 or IDE2, SATA controller will
remap to IDE controller. (Default value)
Manual Set SATA mode manually from SATA Port0 configure as item.
SATA Port0 configure as
IDE Pri. Master Set SATA controller to compatible mode. This mode will remap SATA Port 0 to
IDE Primary Master.
IDE Pri. Slave Set SATA controller to compatible mode. This mode will remap SATA Port 0 to
IDE Primary Slave.
IDE Sec. Master Set SATA controller to compatible mode. This mode will remap SATA Port 0 to
IDE Secondary Master.
IDE Sec. Slave Set SATA controller to compatible mode. This mode will remap SATA Port 0 to
IDE Secondary Slave.
SATA Port0 Set SATA controller to native mode(Serial ATA mode - SATA Port 0). This mode
is only supported by Windows XP or later. (Default value)
SATA Port1 Set SATA controller to native mode(Serial ATA mode - SATA Port 1). This mode
is only supported by Windows XP or later.
SATA Port1 configure as
The setting depends on SATA Port0 configure as item setting. (Default: SATA Port1)
USB Controller
Enabled Enable USB controller. (Default value)
Disabled Disable USB controller.
USB 2.0 Controller
You can disable this function if you are not using onboard USB 2.0 feature.
Enabled Enable USB 2.0 controller. (Default value)
Disabled Disable USB 2.0 controller.
USB Keyboard Support
Enabled Enable USB keyboard support.
Disabled Disable USB keyboard support. (Default value)
USB Mouse Support
Enabled Enable USB mouse support.
Disabled Disable USB mouse support. (Default value)
AC97 Audio
Auto Auto detect AC97 audio function. (Default value)
Disabled Disable AC97 audio function.
Onboard H/W LAN 
Enabled Enable onboard H/W LAN function. (Default value)
Disabled Disable this function.
Only for GA-8IPE1000-G.
Only for GA-8IPE1000-L. 
						

							BIOS Setup - 37 -
EnglishOnboard LAN Boot ROM 
This function decide whether to invoke the boot ROM of the onboard LAN chip.
Enabled Enable this function.
Disabled Disable this function. (Default value)
Onboard Serial Port 1
Auto BIOS will automatically setup the port 1 address.
3F8/IRQ4 Enable onboard Serial port 1 and address is 3F8. (Default value)
2F8/IRQ3 Enable onboard Serial port 1 and address is 2F8.
3E8/IRQ4 Enable onboard Serial port 1 and address is 3E8.
2E8/IRQ3 Enable onboard Serial port 1 and address is 2E8.
Disabled Disable onboard Serial port 1.
Onboard Serial Port 2
Auto BIOS will automatically setup the port 1 address.
3F8/IRQ4 Enable onboard Serial port 2 and address is 3F8.
2F8/IRQ3 Enable onboard Serial port 2 and address is 2F8. (Default value)
3E8/IRQ4 Enable onboard Serial port 2 and address is 3E8.
2E8/IRQ3 Enable onboard Serial port 2 and address is 2E8.
Disabled Disable onboard Serial port 2.
UART Mode Select
This item allows you to determine which Infra Red(IR) function of Onboard I/O chip.
Normal Set onboard I/O chip UART to normal mode. (Default value)
IrDA Set onboard I/O chip UART to IrDA mode.
ASKIR Set onboard I/O chip UART to ASKIR mode.
UR2 Duplex Mode
This feature allows you to seclect IR mode.
This function will available when UART Mode Select doesnt set at Normal.
Half IR Function Duplex Half. (Default value)
Full IR Function Duplex Full.
TxD, RxD Polarity Active
This function will available when UART Mode Select doesnt set at Normal.
Hi, Hi Set TxD, RxD polarity active to Hi, Hi.
Hi, Lo Set TxD, RxD polarity active to Hi, Lo.
Lo, Hi Set TxD, RxD polarity active to Lo, Hi. (Default value)
Lo, Lo Set TxD, RxD polarity active to Lo, Lo.
Use IR Pins
This function will available when UART Mode Select doesnt set at Normal.
RxD2, TxD2 Set IR pins to use RxD2, TxD2.
IR-Rx2Tx2 Set IR pins to use IR-Rx2Tx2. (Default value)
Only for GA-8IPE1000-G.
Only for GA-8IPE1000-L. 
						

							GA-8IPE1000 Series Motherboard - 38 -
English
Onboard Parallel port
Disabled Disable onboard LPT port.
378/IRQ7 Enable onboard LPT port and address is 378/IRQ7. (Default value)
278/IRQ5 Enable onboard LPT port and address is 278/IRQ5.
3BC/IRQ7 Enable onboard LPT port and address is 3BC/IRQ7.
Parallel Port Mode
SPP Using Parallel port as Standard Parallel Port.
EPP1.9+SPP Using Parallel port as Enhanced Parallel Port 1.9 and SPP mode.
ECP Using Parallel port as Extended Capabilities Port.
EPP1.9+ECP Using Parallel port as Enhanced Parallel Port 1.9 and ECP mode.
PRINTER Using Parallel port as printer port. (Default value)
EPP1.7+SPP Using Parallel port as Enhanced Parallel Port 1.7 and SPP mode.
EPP1.7+ECP Using Parallel port as Enhanced Parallel Port 1.7 and ECP mode.
ECP Mode Use DMA
3 Set ECP Mode Use DMA to 3. (Default value)
1 Set ECP Mode Use DMA to 1.
Game Port Address
201 Set Game Port Address to 201. (Default value)
209 Set Game Port Address to 209.
Disabled Disable this function.
Midi Port Address
330 Set Midi Port Address to 330.
300 Set Midi Port Address to 300.
290 Set Midi Port Address to 290.
Disabled Disable this function. (Default value)
Midi Port IRQ
5 Set Midi Port IRQ to 5.
10 Set Midi Port IRQ to 10. (Default value) 
						

							BIOS Setup - 39 -
English2-4 Power Management Setup
ACPI Suspend Type
S1(POS) Set ACPI suspend type to S1/POS(Power On Suspend). (Default value)
S3(STR) Set ACPI suspend type to S3/STR(Suspend To RAM).
Power LED in S1 state
Blinking In standby mode(S1), power LED will blink. (Default value)
Dual/Off In standby mode(S1):
a. If use single color LED, power LED will turn off.
b. If use dual color LED, power LED will turn to another color.
Off by Power button
Instant-off Press power button then Power off instantly. (Default value)
Delay 4 Sec. Press power button 4 seconds to Power off. Enter suspend if button is pressed less
than 4 seconds.
AC BACK Function
Soft-Off When AC-power back to the system, the system will be in Off state. (Default value)
Full-OnWhen AC-power back to the system, the system always in On state.
Memory When AC-power back to the system, the system will return to the Last state before
AC-power off.
PME Event Wake Up
This feature requires an ATX power supply that provides at least 1A on the 5VSB lead.
Disabled Disable this function.
Enabled Enable PME as wake up event. (Default value)
ModemRingOn
An incoming call via modem can awake the system from any suspend state.
Disabled Disable Modem Ring On function.
Enabled Enable Modem Ring On function. (Default value)
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
Power Management Setup
ACPI Suspend Type [S1(POS)]
Power LED in S1 state[Blinking]
Off by Power button [Instant-Off]
AC BACK Function [Soft-Off]
PME Event Wake Up [Enabled]
ModemRingOn[Enabled]
Resume by Alarm [Disabled]
x Date (of Month) Alarm Everday
x Time (hh:mm:ss) Alarm 0 : 0 : 0
POWER ON Function[Disabled]
KLJI: Move Enter: Select +/-/PU/PD: ValueF10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-Save Defaults F7: Optimized Defaults
Item Help
Menu Level` 
						

							GA-8IPE1000 Series Motherboard - 40 -
English
Resume by Alarm
You can set Resume by Alarm item to enabled and key in Date/Time to power on system.
Disabled Disable this function. (Default value)
Enabled Enable alarm function to POWER ON system.
If RTC Alarm Lead To Power On is Enabled.
Date (of Month) Alarm :   Everyday, 1~31
Time (hh: mm: ss) Alarm :  (0~23) : (0~59) : (0~59)
POWER ON Function
Disabled Disable this function. (Default value)
Any KEY Press any key to power on the system.
Mouse Double click on mouse left button to power on the system.
Mouse/Any KEY Press any key or double click on mouse left button to power on the system.