GIGABYTE Ga8ipe1000 User Manual

							Hardware Installation
- 21 -
English6) IDE1 / IDE2 (IDE Connector)
An IDE device connects to the computer via an IDE connector. One IDE con\
nector can connect to one
IDE cable, and the single IDE cable can then connect to two IDE devices \
(hard drive or optical drive). If
you wish to connect two IDE devices, please set the jumper on one IDE de\
vice as Master and the other
as Slave (for information on settings, please refer to the instructions\
 located on the IDE device).
40 39
2
1
7) SATA0 / SATA1 (Serial ATA Connector)
Serial ATA can provide up to 150MB/s transfer rate. Please refer to the BIOS setti\
ng for the Serial ATA
and install the proper driver in order to work properly.
Pin No. Definition
1 GND
2 TXP
3 TXN
4 GND
5 RXN
6 RXP
7 GND
17 
						

							GA-8IPE1000 Series Motherboard - 22 -
English
8) PWR_LED
PWR_LED is connect with the system power indicator to indicate whether the system is on/off. It will
blink when the system enters suspend mode.
Pin No. Definition
1 MPD+
2 MPD-
3 MPD-1
9) BATTERY
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended
by the manufacturer.
Dispose of used batteries according to the manufacturers
instructions.
If you want to erase CMOS...
1. Turn OFF the computer and unplug the power cord.
2. Remove the battery, wait for 30 second.
3. Re-install the battery.
4. Plug the power cord and turn ON the computer. 
						

							Hardware Installation - 23 -
English10)  F_PANEL (Front Panel Jumper)
Please connect the power LED, PC peaker, reset switch and power switch etc. of your chassis front
panel to the F_PANEL connector according to the pin assignment below.
MSG (Message LED/Power/Sleep LED) Pin 1: LED anode(+)
(Yellow) Pin 2: LED cathode(-)
PW (Power Switch) Open: Normal Operation
(Red) Close: Power On/Off
SPEAK (Speaker Connector) Pin 1: VCC(+)
(Amber) Pin 2- Pin 3: NC
Pin 4: Data(-)
HD (IDE Hard Disk Active LED) Pin 1: LED anode(+)
(Blue) Pin 2: LED cathode(-)
RES (Reset Switch) Open: Normal Operation
(Green) Close: Reset Hardware System
NC (Purple) NC
12
1920
HD- HD+
RES+ RES-
NC
IDE Hard Disk Active LED
Reset Switch
SPEAK- MSG-MSG+
PW-PW+
Message LED/
Power/
Sleep LEDSpeaker Connector
SPEAK+
Power
Switch 
						

							GA-8IPE1000 Series Motherboard - 24 -
English
11) F_AUDIO (Front Audio Panel Connector)
If you want to use Front Audio connector, you must remove 5-6, 9-10 Jumper.
In order to utilize the front audio header, your chassis must have front audio connector. Also please
make sure the pin assigment on the cable is the same as the pin assigment on the MB header. To find
out if the chassis you are buying support front audio connector, please contact your dealer. Please note,
you can have the alternative of using front audio connector or of using rear audio connector to play
sound.
12) CD_IN (CD In Connector)
Connect CD-ROM or DVD-ROM audio out to the connector.
Pin No. Definition
1 CD-L
2 GND
3 GND
4 CD-R
1
Pin No. Definition
1 MIC
2 GND
3 MIC_BIAS
4 Power
5 Front Audio (R)
6 Rear Audio (R)
7 Reserved
8 No Pin
9 Front Audio (L)
10 Rear Audio (L)
10 92 1 
						

							Hardware Installation - 25 -
English13) SUR_CEN (Surround Center Connector)
Please contact your nearest dealer for optional SUR_CEN cable.
14) SPDIF_IO (SPDIF In / Out Connector)
The SPDIF output is capable of providing digital audio to external speakers or compressed AC3 data to
an external Dolby Digital Decoder. Use this feature only when your stereo system has digital input
function. Be careful with the polarity of the SPDIF_IO connector. Check the pin assignment carefully
while you connect the SPDIF cable, incorrect connection between the cable and connector will make
the device unable to work or even damage it. For optional SPDIF_IO cable, please contact your local
dealer.
Pin No. Definition
1 SUR OUTL
2 SUR OUTR
3 GND
4 No Pin
5 CENTER_OUT
6 BASS_OUT
7 AUX_L
8 AUX_R
8 72 1
Pin No. Definition
1 VCC
2 No Pin
3 SPDIF
4 SPDIFI
5 GND
6 GND
1 2
5 6 
						

							GA-8IPE1000 Series Motherboard - 26 -
English
15) F_ USB1 / F_USB2 (Front USB Connector)
Be careful with the polarity of the front USB connector. Check the pin assignment carefully while you
connect the front USB cable, incorrect connection between the cable and connector will make the
device unable to work or even damage it. For optional front USB cable, please contact your local dealer.
Pin No. Definition
1 Power
2 Power
3 USB DX-
4 USB Dy-
5 USB DX+
6 USB Dy+
7 GND
8 GND
9 No Pin
10 NC
16) IR
Be careful with the polarity of the IR connector while you connect the IR. Please contact your nearest
dealer for optional IR device.
Pin No. Definition
1 VCC
2 No Pin
3 IR RX
4 GND
5 IR TX
1
2
10
1
9 
						

							Hardware Installation - 27 -
English17) GAME (GAME Connector)
This connector supports joystick, MIDI keyboard and other relate audio devices.
Pin No. Definition
1 VCC
2 GRX1_R
3 GND
4 GPSA2
5 VCC
6 GPX2_R
7 GPY2_R
8 MSI_R
9 GPSA1
10 GND
11 GPY1_R
12 VCC
13 GPSB1
14 MSO_R
15 GPSB2
16 No Pin
18) INFO_LINK
This connector allows you to connect some external devices to provide you extra function.
Pin No. Definition
1 SMBCLK
2 VCC
3 SMBDATA
4 GPIO
5 GND
6 GND
7 No Pin
8NC
9 +12V
10 +12V
2
16
1
15
2
10
1
9 
						

							GA-8IPE1000 Series Motherboard - 28 -
English
19) CLR_CMOS (Clear CMOS)
You may clear the CMOS data to its default values by this jumper. To clear CMOS, temporarily short
1-2 pin. Default doesnt include the Shunter to prevent from improper use this jumper.
Open: Normal
Short: Clear CMOS
11 
						

							BIOS Setup - 29 -
English
BIOS (Basic Input and Output System) includes a CMOS SETUP utility which allows user to configure
required settings or to activate certain system features.
The CMOS SETUP saves the configuration in the CMOS SRAM of the motherboard.
When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS
SRAM.
When the power is turned on, pushing the  button during the BIOS POST (Power-On Self Test) will
take you to the CMOS SETUP screen.  You can enter the BIOS setup screen by pressing Ctrl + F1.
When setting up BIOS for the first time, it is recommended that you save the current BIOS to a disk in the
event that BIOS needs to be reset to its original settings. If you wish to upgrade to a new BIOS, either
GIGABYTEs Q-Flash or @BIOS utility can be used.
Q-Flash allows the user to quickly and easily update or backup BIOS without entering the operating system.
@BIOS is a Windows-based utility that does not require users to boot to DOS before upgrading BIOS but
directly download and update BIOS from the Internet.
CONTROL KEYS
   < > Move to select item
 Select Item
 Main Menu - Quit and not save changes into CMOS Status Page Setup Menu
and Option Page Setup Menu - Exit current page and return to Main Menu
 Increase the numeric value or make changes
 Decrease the numeric value or make changes
 General help, only for Status Page Setup Menu and Option Page Setup Menu
 Item Help
 Restore the previous CMOS value from CMOS, only for Option Page Setup Menu
 Load the file-safe default CMOS value from BIOS default table
 Load the Optimized Defaults
 Q-Flash utility
 System Information
 Save all the CMOS changes, only for Main Menu
Main Menu
The on-line description of the highlighted setup function is displayed at the bottom of the screen.
Status Page Setup Menu / Option Page Setup Menu
Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selec-
tions for the highlighted item. To exit the Help Window press .
Chapter 2  BIOS Setup 
						

							GA-8IPE1000 Series Motherboard - 30 -
English
The Main Menu (For example: BIOS Ver. : E8)
Once you enter Award BIOS CMOS Setup Utility, the Main Menu (as figure below) will appear on the screen.
Use arrow keys to select among the items and press  to accept or enter the sub-menu.
If you cant find the setting you want, please press Ctrl+F1 to search the advanced option hidden.
„ „„ „
„Standard CMOS Features
This setup page includes all the items in standard compatible BIOS.
„ „„ „
„Advanced BIOS Features
This setup page includes all the items of Award special enhanced features.
„ „„ „
„Integrated Peripherals
This setup page includes all onboard peripherals.
„ „„ „
„Power Management Setup
This setup page includes all the items of Green function features.
„ „„ „
„PnP/PCI Configuration
This setup page includes all the configurations of PCI & PnP ISA resources.
„ „„ „
„PC Health Status
This setup page is the System auto detect Temperature, voltage, fan, speed.
„ „„ „
„Frequency/Voltage Control
This setup page is control CPU clock and frequency ratio.
„ „„ „
„Load Fail-Safe Defaults
Fail-Safe Defaults indicates the value of the system parameters which the system would be in safe
configuration.
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
`Standard CMOS Features
`Advanced BIOS Features
`Integrated Peripherals
`Power Management Setup
`PnP/PCI Configurations
`PC Health Status
`Frequency/Voltage ControlLoad Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving
ESC: QuitKLJI: Select Item
F8: Q-Flash F10: Save & Exit Setup
Time, Date, Hard Disk Type...