GGP Italy SPA Trimmer HT60K HT75K Instructions Manual

24PREPARING TO WORKEN
CHECKING THE MACHINE
Before starting work please:
–Check that all the screws on the machine and
the blade are tightly fastened;
–check that the blades are sharp and there are
no signs of any damage;
–check that the air filter is clean;
–check that the protection devices are well fas-
tened and working efficiently;
–check that the handgrips are well fastened
PREPARING THE FUEL 
This machine is fitted with a two-stroke engine
which requires a mix of petrol and lubricating oil.
Using...

PREPARING TO WORK / HOW TO START - USE – STOP THE ENGINE 25EN
Periodically clean the petrol
and fuel mix containers to remove any eventual
deposits.
REFUELLING
Never smoke whilst refu-
elling and avoid inhaling the petrol fumes.
Carefully open the tank top
as pressure could have formed inside
Before refuelling:
–Shake the fuel mix container well.
–Place the machine on a flat stable surface,
with the fuel tank cap facing upwards.
!WARNING!
!DANGER!
IMPORTANT–Clean the fuel tank cap and the surrounding...

7. Gradually release the handle (4) on the starter
wire to avoid it from returning too fast and out
of control.
8. Turn the starter control lever  (3) to the “RUN”
position.
The starter lever  (3) will
automatically return to the  “RUN” position as
soon as the accelerator lever (5) is activated.
9. Allow the engine to run at minimum speed for
at least one minute before accelerating to
maximum speed.
If the handle (4) on the starter
wire is pulled repeatedly with the starter control
lever (3) in the...

USING THE MACHINE27EN
To respect persons and the environment :
–Please try not to cause any disturbance.
–Scrupolously comply with local regulations
and provision for disposal of waste materi-
als after trimming.
–Scrupolously comply with local regulations
and provision for the disposal of oils,
petrol, damaged parts or any element
which has a strong impact on the environ-
ment.
Always wearing suitable
clothing when using the machine. Your retail-
er can provide you with all the information on
the most...

28MAINTENANCE AND PRESERVATION EN
Correct maintenance is essential to maintain the
original efficency and safety of the machine over
time.
During maintenance oper-
ations:
–remove the spark plug cap.
–Wait until the engine is sufficiently cold.
–Use protective gloves when handling the
blades.
–Keep the blade protection devices on,
except when intervening directly on the
blade.
–Never dispose of oils, fuel or other polluting
materials in unauthorised places
CLEANING THE ENGINE AND THE SILENCER
To reduce...

MAINTENANCE AND PRESERVATION 29EN
on the contrary ask your Retailer to check the
carburettor and the engine.
•
Tuning minimum speed  (Fig. 11)
The minimum speed must
only be tuned if the blades move when the
engine is ticking over.
Reduce the speed by turning the screw (1)
counter-clockwise until the blades come to a
halt and function correctly.
If the engine does not tick over regularly, turn the
screw (1) clockwise to increase the speed.
The blades must not move
when the engine ticks over; contact...

PRESERVATION
After each working session, carefully clean the
machine from dust and debris, repair or replace
any faulty parts and lubricate the blades to pre-
vent them from rusting.
The machine must be preserved in a dry area,
protected from all weather conditions and with
the blade protection device correctly fitted.
PROLONGED IDLE PERIODS
If the machine will not be
used for a period of more than 2-3 months it is
recommended to follow some advice to avoid
difficulty when you wish to use the machine...

TECHNICAL SPECIFICATIONS31EN
MODELL.........................................................................HT 60K HT 75K
Displacement ......................................................... cm322.5 22.5
Power ....................................................................... kW 1.0 1.0
Spark plug  ...................................................................... NGK BPMR6A NGK BPMR6A 
Petrol : oil ratio   .............................................................. 50 : 1 50 : 1
Tank...

32