GGP Italy SPA Trimmer HT60K HT75K Instructions Manual

71501018/1
Realizzazione: EDIPROM / bergamo   -   PRINTED IN ITALY
GGP ITALY 
SPA
 • Via del Lavoro, 6 • I-31033 Castelfranco Veneto (TV) ITALY
FRENNLDEESPTEL
Tosasiepi portatile - MANUALE DI ISTRUZIONI
ATTENZIONE: prima di utilizzare la macchina, leggere
attentamente il presente libretto.
Portable Hedge Trimmer - OPERATOR’S MANUAL
WARNING: read thoroughly the instruction booklet before
using this machine.
Taille-haies portable - MANUEL D’UTILISATION
ATTENTION: lire attentivement le manuel avant...

ITALIANO .................................. 5
ENGLISH ................................ 19
FRANÇAIS .............................. 33
DEUTSCH .............................. 47
ESPAÑOL ............................... 61
NEDERLANDS ......................... 75
PORTUGUÊS........................... 89
∂££∏¡π∫∞........................... 103
TÜRKÇE............................... 117
SVENSKA ............................. 131
SUOMI .................................. 145
DANSK ....................................

2
12
345
1
« I »1
« I »
5
5
2
344
1
2
3
1
3
2
1
1
2
2
« O »
« O »
1
1
1
2
3 

3
6
89
1011
1214
7
1
2
3
0,75 mm
1
2
332
–1+
1
13
1
2
3
1
2
45°
5-10° 

4 

INTRODUCTION19EN
Dear Customer,
thank you for choosing one of our products. We hope that you will be completely satisfied with this
machine and that it fully meets your expectations. This manual has been compiled in order to provide
you with all the information you need to get acquainted with the machine and use it safely and effi-
ciently. Don’t forget that it is an integral part of the machine, so keep it handy so that it can be con-
sulted when necessary, and pass it on to a further user if you resell...

20IDENTIFICATION OF MAIN COMPONENTSEN
1. Engine
2. Cutting device (blade)
3. Cutter protection plate
4. Front handgrip
5. Rear handgrip
6. Rear handgrip release
command
7. Fuel tank cap
8. Starter button
9. Blade protection  
10. Registration plate
CONTROLS
11. Engine stop switch 
12. Blade command
(Accelerator lever)
13. Accelerator safety
lever
14. Starter 
1. IDENTIFICATION OF MAIN COMPONENTS
1
4
56
78
9
32
10
11
12
13
14
REGISTRATION PLATE
10.1) Mark of conformity with EC 98/37 stan-
dards
10.2) Name...

SYMBOLS21EN
1)Warning! Danger.
2)Read the instruction manual before using the
machine.
3)Irreversible damage can be caused to your
hearing. 
Anyone operating this machine under normal
conditions during continuous daily use may be
exposed to a noise level equal to or exceeding
85 dB (A). 
The operator must wear Personal Protective
Equipment (PPE). 
Whenever the machine is in use, safety goggles
must be worn to safeguard against flying
objects, as must ear protectors, such as a
soundproof helmet, in order...

22SAFETY REQUIREMENTSEN
A) TRAINING
1) Read the instructions carefully. Become
acquainted with the controls and the proper use
of the machine. Learn how to stop the engine
quickly.
2) Only use the machine for its intended use, that
is 
“the cutting and trimming of hedges, con-
sisting in plants with small sized branches”.
Any other use may be dangerous and severly
damage the machine.
3) Never allow children or persons unfamiliar
with these instructions to use the machine. Local
regulations may restrict...

SAFETY REQUIREMENTS23EN
4) Start the engine when the machine is firmly on
the ground and hold it in place with your free
hand: 
– start the motor in an area at least 3 metres
from where you refuelled;
– check that there are no persons in the vicinity
of the machine;
– do not direct the silencer and therefore the
exhaust fumes towards inflammable materials.
5) Do not change the engine tuning and do not
rev the engine excessively at maximum speed.
6) Check that when the machine is running at
minimum speed...