GGP Italy SPA Lawn Mower 102-122 Instructions Manual

EN 40MAINTENANCE
6.2.3 ENGINE
Follow all the instructions in the engine
manual.
To empty the engine oil, unscrew the oil
plug (1). When refitting the plug, make sure
the seal is positioned correctly.
6.2.4 R
EAR AXLE
This is a sealed single unit which does not require maintenance. It is permanently
lubricated and this lubricant does not need changing or topping up.
6.2.5 B
ATTERY
To ensure long life to the battery it is essential to keep it carefully maintained.
The machine battery must always be...

This connector must only be used for connection to the
CB01 maintenance battery-charger. For its use:
– follow the instructions given in the relative instruction booklet,
– follow the instructions given in the battery booklet.
6.3 CHECKS AND ADJUSTMENTS
Summary of the main situations where work may be required
6.3.1 D
ISMANTLING, SHARPENING AND BALANCING BLADES
Check that the blade is sharpened properly and firmly fixed to the bracket.
– A badly sharpened blade pulls at the grass and causes the lawn to...

a right-hand thread and the other one has a left-hand thread.
Sharpen the two cutting edges using a medium grade grinding wheel and check
the balance by holding the blade up with a round 18 mm Ø bar inserted in the
central hole.
Damaged or bent blades must always be
replaced; never try to repair
them! ALWAYS USE MANUFAC-
TURERS GENUINE REPLACE-
MENT BLADES BEARING THE
SYMBOL !
The blades dif-
fer, are at 90° to one another, and
are contra-rotating. When
installing them, make sure that
they are correctly...

For achieving good results
from cutting, the front part should always be 5 -
6 mm lower than the rear.
– Put the machine onto a flat surface and check
the tyre pressures;
– put 26 mm blocks (1) under the front edge of
the deck and 32 mm blocks (2) under the rear
edge, and thenput the lifting lever into position
«1»;
– loosen the nuts (3), the screws (5) and the lock-
nuts (4 – 6) on both the right and left side, so
that the deck is resting firmly on the blocks;
–  push the two connecting rods (7) to the...

For models with electromagnetic clutch
If there is an unusual rotation due to
the belt; turn the adjusting nut (1) till
the correct spring length is achieved
(measured from the outer ends of the
spring).
If the electromagnetic clutch does not
manage to drive the belt or the blades
do not stop within few seconds, imme-
diately contact a Licensed Service
Centre.
6.3.4 B
RAKE ADJUSTMENT
If the braking distance becomes longer than
the amount indicated (☛5.3.6), the brake
spring will need to be adjusted.
The...

adjustment, immediately contact the Licensed Service Centre. DO NOT
ATTEMPT OTHER WORK ON THE BRAKE THAN DESCRIBED HERE.
6.3.5 A
DJUSTING THE TENSION OF THE DRIVE BELT
If you should notice that forward drive power
has dropped, it will be necessary to adjust
the tension of the spring of the stretcher to
return to former conditions.
Access for making this adjustment is by tak-
ing off the inspection hatch beneath the seat.
Loosen the locking nuts (2) and tighten or
loosen the screw (1) as much as...

6.4 DISMANTLING AND REPLACEMENT
6.4.1 R
EPLACING WHEELS
Stop the machine on a flat surface and put a block
under a load-bearing part of the frame on the side
that the wheel is to be changed.
The wheels are held by a snap ring (1) which can be
eased off with a screwdriver.
The rear wheels are directly coupled to the differen-
tial axle shaft and fastened by a key that forms part
of the wheels hub.
Should you substitute one or both rear wheels, ensure that
they are of the same diameter, and check that...

6.4.4 REPLACING A FUSE
The machine is fitted with fuses (1) with different capacities and functions.
Specifically:
– 10 A fuse = protects the main and
power circuits of the electronic board.
When it blows, the machine stops and
the dashboard switches off.
– 25 A fuse  = protects the battery charg-
er circuit. When it blows, the battery
light comes on to indicate that the bat-
tery is going to run out and the
machine will have problems starting.
The fuse capacity is indicated on the
fuse.
A blown fuse...

EN 48TROUBLESHOOTING
7. TROUBLESHOOTING
PROBLEM LIKELY CAUSE SOLUTION
1.With the key at
«ON» the dashboard
remains off with no
audible signal.
2.With the key at
«ON» the dashboard
remains off, but there
is an audible signal. 
3.With the key on
«START» the dash-
board comes on but
the starter motor does
not runa
4.With the key on
«START» the starter
motor runs but the
engine does not start
5. Starting is difficult
or the engine runs
erratically
6.Weak engine per-
formance during cut-
tingThe protection of...

EN 49 TROUBLESHOOTING
PROBLEM LIKELY CAUSE SOLUTION
7.Engine stops when
blades are engaged
8.The battery warning
light does not turn off
after a few minutes’
work
9.The oil warning
light comes on while
working ( if fitted)
10.The engine stops
and an audible signal
is heard
11.The engine stops
with no audible warn-
ing
12.The blades warn-
ing light stays lit when
the blades are disen-
gaged
13.The blades do not
engage 
( models with 
lever operated
engagement)
➤
➤
– you are not ready to engage the blades...