GGP Italy SPA Electric Chain Saw Manual

The machine is supplied with
the bar and chain dismantled and the oil tank
empty. . 
! Always wear heavy-duty
gloves when handling the bar and chain.
Mount the bar and chain very carefully so as
not to impair the safety and efficiency of the
machine. If in doubt, contact your dealer.
The machine can be assem-
bled in different ways, depending on the bar fas-
tening system and the chain tensioning mecha-
nism.
Before fitting the bar, make sure the chain brake
is not engaged; this is done by pulling the...

ENPREPARING TO WORK / HOW TO START - STOP THE ENGINE7
CHECKING THE MACHINE
Make sure the machine is
not plugged into the mains socket.
Before starting work please:
–check that the mains frequency and voltage is
the same as the rating data on the
“Identification Plate” (see chap. 1 - 10.8).
–check that all the screws on the machine and
the bar are tightly fastened;
–check that the chain is sharp and there are no
signs of any damage;
–check that the protection devices are well fas-
tened and working...

EN
To respect people and the environment:
– Try not to cause any disturbance.
– Scrupulously comply with local regulations
and provisions for the disposal of waste
materials after sawing.
– Scrupulously comply with local regulations
and provisions for the disposal of oils, dam-
aged parts or any elements which have a
strong impact on the environment.
Always wear suitable
clothing when using the machine. Your deal-
er can provide you with all the information on
the most suitable accident-prevention...

EN
•Delimbing (Fig. 14)
Make sure there is nothing
or nobody in the area where the branches will
fall.
1. Stand opposite the branch you want to cut.
2. Start cutting lower branches followed by the
higher ones.
3. Cut downwards to prevent the bar from get-
ting jammed.
•
Felling (Fig. 15)
When felling on slopes,
always stand uphill from the tree and check
that the felled trunk cannot cause damage if
it rolls down the hill.
1. Decide where the tree should fall – you
should consider the wind, the natural...

Correct maintenance is essential to maintain the
original efficiency and safety of the machine over
time.
During maintenance oper-
ations:
–Unplug the machine from the mains.
–Use protective gloves when handling the
bar and chain.
–Keep the bar protection devices on, except
when intervening directly on the bar or the
chain.
–Never dispose of oils or other polluting
materials in unauthorised places.
ENGINE COOLING
To avoid overheating and damage to the engine,
always keep the cooling air vents clean and...

–After sharpening, remove all traces of filing
and dust and lubricate the chain in an oil bath.  
Replace the chain whenever:
–The length of the cutting edges reduces to 5
mm or less;
–There is too much play between the links and
the rivets.
BAR MAINTENANCE (Fig. 22)
To avoid asymmetrical wear on the bar, make
sure it is turned over periodically.
To keep the bar in perfect working order, pro-
ceed as follows:
–Grease the bearings on the nose sprocket (if
present) with the syringe.
–Clean the bar groove...

EN12 

71501048/0Realizzazione: EDIPROM / bergamo
GGP ITALY 
SPA
Via del Lavoro, 6
I-31033 Castelfranco Veneto (TV) ITALY 

19
A passthrough device is a device that you add to your system that a sign\
al passes through 
unaltered. 
For example,  if you use your DVD recorder (or VCR) to record shows from your satellite or 
set top box, you may need to add your DVD recorder as a passthrough device.
In these examples, the DVD Recorder and the A/V Switch are used as passthrough 
devices.
Adding an extra device (passthrough) to an Activity
To add an extra Device (Passthrough) to an Activity, go to your home page:
Select the...

0

When you select an Activity, your Harmony One turns on all the required entertainment 
devices, sets up the device inputs correctly, and sets up the remote’s buttons to control 
the devices in the Activity.  For example, when you select the Watch a DVD Activity, the 
volume buttons on the Harmony One changes the volume.
However, there may be some commands you want to add to buttons or display on the 
remote’s screen. Using the Harmony Remote Software you can add or customize how 
buttons work in...