GGP Italy SPA Chainsaw P360 171501052/0 Instructions Manual

fino all’arresto, in modo da consumare tutto il
carburante rimasto nel carburatore.
–Lasciare raffreddare il motore e smontare la
candela.
–Versare nel foro della candela un cucchiaino
d’olio (nuovo) per motori a 2 tempi.
–Tirare diverse volte la manopola di avviamen-
to per distribuire l’olio nel cilindro.
–Rimontare la candela con il pistone al punto
morto superiore (visibile dal foro della candela
quando il pistone è alla sua corsa massima).•Ripresa dell’attività
Al momento di rimettere in funzione la...

16 

ENINTRODUCTION1
Dear Customer,
thank you for choosing one of our products. We hope that you will be completely satisfied with this
machine and that it fully meets your expectations. This manual has been compiled in order to provide
you with all the information you need to get acquainted with the machine and use it safely and effi-
ciently. Don’t forget that it is an integral part of the machine, so keep it handy so that it can be con-
sulted when necessary, and pass it on to a further user if you resell...

EN
MAIN COMPONENTS
1. Power unit
2. Spiked bumper
3. Front hand guard
4. Front handgrip
5. Rear handgrip
6. Chain catcher
7. Bar
8. Chain
9. Bar cover  
10. Identification plate
CONTROLS AND REFUELLING 
11. Engine stop switch
12. Throttle trigger
13. Throttle trigger lockout
14. Starter
15. Choke (if present)
16. Primer (if present)
17. Decompression valve (if present)
21. Fuel tank cap
22. Chain oil tank cap 2
IDENTIFICATION OF MAIN COMPONENTS
1. IDENTIFICATION OF MAIN COMPONENTS
IDENTIFICATION PLATE...

EN
1)Warning! Danger. The failure to use this
machine correctly can be hazardous for oneself
and others.
2)Beware of kickback! Kickback is the rapid
and uncontrollable backward motion of the
chain-saw in the direction of the operator.
Always work in complete safety. Use chains with
safety links that limit kickback.  
3)Never hold the machine with one hand! Hold
the machine fast with both hands to control the
machine and reduce the risk of kickback.
11)Fuel tank
12)Chain oil tank and oil flow adjuster...

EN
A) TRAINING
1)Read the instructions carefully.Become
acquainted with the controls and the proper use
of the machine. Learn how to stop the engine
quickly.
2) Only use the machine for the purpose for
which it was designed, that is for 
“felling, buck-
ing and delimbing trees with dimensions suit-
able for the length of the bar”
or wooden
objects with the same characteristics. Any other
use may be dangerous and damage the
machine.
3) Never allow children or persons unfamiliar
with these instructions to...

to the lay of the land and any eventual obsta-
cles.
–avoid working alone or in an isolated place, in
case you have to find help after an accident.
4) Make sure the machine is securely locked
when you start the engine:  
–start the motor in an area at least 3 metres
from where you refuelled;
–check that there are no persons in the vicinity
of the machine;
–do not direct the silencer and therefore the
exhaust fumes towards inflammable materials.
–watch out for flying debris caused by the
movement of the...

The machine is supplied with
the bar and chain dismantled and the oil and fuel
tanks empty.  
Always wear heavy-duty
gloves when handling the bar and chain.
Mount the bar and chain very carefully so as
not to impair the safety and efficiency of the
machine. If in doubt, contact your dealer.
The machine can be assem-
bled in different ways, depending on the bar fas-
tening system and the chain tensioning mecha-
nism.
Before fitting the bar, make sure the chain brake
is not engaged; this is done by pulling...

PREPARING TO WORK7EN
CHECKING THE MACHINE
Before starting work please:
–check that all the screws on the machine and
the bar are tightly fastened;
–check that the chain is sharp and there are no
signs of any damage;
–check that the air filter is clean;
–check that the protection devices are well fas-
tened and working efficiently;
–check that the handgrips are well fastened;
–check that the chain brake is working effi-
ciently.
PREPARING THE FUEL
This machine is fitted with a two-stroke engine
which...

EN
Periodically clean the petrol
and fuel mixture containers to remove any even-
tual deposits.
REFUELLING
Never smoke whilst refu-
elling and avoid inhaling the petrol fumes.
Carefully open the tank top
as pressure could have formed inside.
Before refuelling:
–Shake the fuel mixture container well.
–Place the machine on a flat stable surface,
with the fuel tank cap facing upwards.
–Clean the fuel tank cap and the surrounding
area to avoid any dirt from entering the tank
during refilling.
–Carefully open...