GGP Italy SPA Chainsaw P360 171501052/0 Instructions Manual

ENHOW TO START - USE – STOP THE ENGINE9
If the machine is not held
firmly, the force of the engine could cause the
user to lose his balance or direct the bar
towards him or an obstacle.
7. Pull the starter rope slowly for 10 - 15 cm until
you feel some resistance, then tug it hard a
few times until you hear the engine turn over.
To avoid breaking the starter
rope, do not pull the whole length of it or let it
slide along the edge of the cable guide hole.
Release the starter gradually, to avoid letting it...

EN
To respect people and the environment:
– Try not to cause any disturbance.
– Scrupulously comply with local regulations
and provisions for the disposal of waste
materials after sawing.
– Scrupulously comply with local regulations
and provisions for the disposal of oils,
petrol, damaged parts or any elements
which have a strong impact on the environ-
ment.
Always wear suitable
clothing when using the machine. Your deal-
er can provide you with all the information on
the most suitable...

•Delimbing (Fig. 16)
Make sure there is nothing
or nobody in the area where the branches will
fall.
1. Stand opposite the branch you want to cut.
2. Start cutting lower branches followed by the
higher ones.
3. Cut downwards to prevent the bar from get-
ting jammed.
•
Felling (Fig. 17)
When felling on slopes,
always stand uphill from the tree and check
that the felled trunk cannot cause damage if
it rolls down the hill.
1. Decide where the tree should fall – you
should consider the wind, the natural lean...

Correct maintenance is essential to maintain the
original efficiency and safety of the machine over
time.
During maintenance oper-
ations:
–Remove the spark plug cap.
–Wait until the engine is sufficiently cold.
–Use protective gloves when handling the
bar and chain.
–Keep the bar protection devices on, except
when intervening directly on the bar or the
chain.
–Never dispose of oils, fuel or other polluting
materials in unauthorised places.
CYLINDER AND SILENCER
To reduce fire risks, periodically clean...

(1a) and then fit these assembled parts on the
machine.
CHECKING THE SPARK PLUG (Fig. 24)
Periodically remove and clean the spark plug
using a metal brush to get rid of any deposits.
Check and reset the correct distance between
the electrodes.
Replace the spark plug and fasten it firmly using
the supplied wrench.
The spark plug must be replaced with one with
the same characteristics whenever the elec-
trodes have burnt or the insulation has worn, and
in any case every 100 working hours.
TUNING THE...

BAR MAINTENANCE (Fig. 26)
To avoid asymmetrical wear on the bar, make
sure it is turned over periodically.
To keep the bar in perfect working order, pro-
ceed as follows:
–grease the bearings on the nose sprocket (if
present) with the syringe;
–clean the bar groove with the scraper;
–clean the lubrication holes;
–with a flat file, remove burr from the edges and
level off the guides.
Replace the bar whenever:
–the groove is not as deep as the height of the
drive links (which must never touch the bot-...

a halt, so that it uses up all the fuel that is left
in the carburettor.
–Wait for the engine to cool down and remove
the spark plug.
–Pour a teaspoon of (new) 2-stroke engine oil
into the spark plug slot.
–Pull the starter rope several times to deliver oil
to the cylinder..
–Replace the spark plug with the piston in the
dead end upper position (visible from the
spark plug slot when the piston is at maximum
stroke).•Restarting work
When you wish to start using the machine again:
–Remove the spark plug....

16 

FRPRÉSENTATION1
Cher Client,
Nous tenons avant tout à vous remercier de la préférence que vous avez accordée à nos produits, et nous sou-
haitons que votre machine vous réserve de grandes satisfactions et réponde pleinement à vos attentes. Ce
manuel a été rédigé dans le but de vous permettre de bien connaître votre machine et de l’utiliser en toutes condi-
tions de sécurité et d’efficacité; n’oubliez pas qu’il fait partie intégrante de la machine, tenez-le à portée de main
pour le consulter à tout...

FR
PIÈCES PRINCIPALES
1. Ensemble moteur
2. Griffe d’abattage
3. Protecteur de la main tenant la
poignée avant
4. Poignée avant
5. Poignée arrière
6. Enrouleur de chaîne
7. Guide-chaîne
8. Chaîne
9. Protecteur de guide-chaîne  
10. Étiquette matricule
COMMANDES ET PLEIN DE CARBURANT
11. Interrupteur marche-arrêt du moteur
12. Commande d’accélérateur
13. Blocage de l’accélérateur au démarrage
14. Lanceur
15. Commande du starter (s’il y en a un)
16. Commande du dispositif d’amorçage
(Primer) (s’il y en a...