Getnet Router GR-534W User Manual

 
6    

 
7 
3   Network Configuration and Introduction to 
Network Connection Modes 
Web management tool allows you to configure GR-534W. The recommended 
browser is Internet Explorer 5.0 version or above. 
The following sections describe how to set the Internet connection, local Ethernet 
connection, and wireless connection, and how to access the Web page of the 
GR-534W. 
3.1   TCP/IP Settings 
By default, the IP address of LAN interface of the GR-534W is 192.168.1.1.The 
subnet mask is 255.255.255.0. The...

 
8 
Step2 Right click the network adapter icon and select Properties in the menu. 
The Local Area Connections Properties appears. (Note: If there are 
several network cards on your PC, it may not display the Local Area 
Connections Properties page. It may display other dialog boxes.) 
 
 
Step3 Double click the Internet Protocol (TCP/IP) to display the Internet 
Protocol (TCP/IP) Properties page.  

 
9 
 
 
Step4 Select Use the following IP address and enter the IP address of the 
network adapter. The IP address should belong to the IP network segment 
192.168. 1.X (X is a number between 2 and 254). 
 
Step5 Set subnet mask and then click the OK button to finish manual setting.  

 
10 
Step6 After finishing setting, you may ping the default IP address of the 
GR-534W, to check whether the current connection between PC and the 
GR-534W is normal. Click RUN… in the lower left corner on the desktop, 
and then enter ping 192.168.1.1 in the dialog box. See the following 
figure: 
 
 
Note: 
192.168.1.1 is the default IP address of the LAN interface. If this IP address is 
changed and you need to ping the IP address of the GR-534W, you should enter the 
current IP address in the dialog...

 
11 
If you want to access the Internet via the GR-534W, there are two common access 
ways, including PPPoE and DHCP (Auto config). The following sections describe the 
common network connection modes of these two ways. 
 
Note: 
In the gateway mode, GR-534W provides 5 types of uplink access modes, including 
STATIC (fixed IP), DHCP (Auto config), PPPoE (ADSL), L2TP, and PPTP. For more 
details, please refer to 5.3.2 WAN. 
  The Network Connection Mode of PPPoE 
 
 
If you access the Internet by PPPoE,...

 
12 
 
 
Step5 On the Wide Area Network (WAN) Settings page, set the WAN 
Connection Type to be PPPoE (ADSL) and enter the correct PPPoE 
username and password. After finishing setting, click the Apply button to 
start dial-up. 
 
  The Network Connection Mode of DHCP (Auto config) 
 
 
If you can access the Internet without dial-up, and ISP provides DHCP service, 
please follow the steps below to finish setting. 
Step1 Use one Ethernet cable to connect the uplink interface of router or 
gateway to the...

 
13 
automatically. If you want to manually set the TCP/IP properties, please 
refer to 3.1 TCP/IP Settings. 
Step3 Log in to the Web page of the GR-534W. Click Internet > WAN to display 
the Wide Area Network (WAN) Settings page. On this page, set WAN  
Connection Type to be DHCP (Auto config). 
 
 
Step4 After finishing settings, click the Apply button, and then GR-534W starts 
to acquire the parameters assigned by the DHCP server, such as the IP 
address, and the DNS address. 
 
3.3   Connection...

 
14 
Network Connection icon and select View Available Wireless 
Networks. 
 
 
Step2 On the Wireless Network Connection page, click Refresh network list 
and the network list will be refreshed. The default SSID of the GR-534W is 
Getnet. Choose the AP that you want to connect, and then click the 
Connect button. The default wireless security mode is Disable, and you 
can connect AP directly without the encryption key. If the GR-534W is 
encrypted, this AP is marked with a lock icon.
  

 
15 
 
 
Step3 If the GR-534W is encrypted, you need to enter the encryption key in the 
field of network key and then click the Connect button. 
 
 
Step4 If the wireless network card connects to GR-534W successfully, the 
character Connected will appear in the AP’s upper right corner.