GE Logiq 9 User Manual

Safety Precautions
LOGIQ E9 User Guide 4-19
Direction 5180302-100 Rev. 1
EMC (Electromagnetic Compatibility) (continued)
NOTE:  Do not use devices which intentionally transmit RF Signals 
(cellular phones, transceivers, or radio controlled products) 
other than those supplied by GE (wireless microphone, 
broadband over power lines, for example) in the vicinity of the 
equipment as it may cause performance outside the published 
specifications. Keep the power to these type devices turned off 
when near...

Safety
4-20 LOGIQ E9 User Guide
Direction 5180302-100 Rev. 1
EMC Performance (continued)
Portable and mobile radio communications equipment (e.g. two-
way radio, cellular/cordless telephones, wireless computer 
networks) should be used no closer to any part of this system, 
including cables, than determined according to the following 
method: 
CAUTIONDo not use devices which intentionally transmit RF signals 
(cellular phones, transceivers, or radio controlled products), 
other than those supplied by GE...

Safety Precautions
LOGIQ E9 User Guide 4-21
Direction 5180302-100 Rev. 1
Notice upon Installation of Product
Separation distance and effect from fixed radio communications 
equipment: field strengths from fixed transmitters, such as base 
stations for radio (cellular/cordless) telephones and land mobile 
radios, amateur radio, AM and FM radio broadcast, and TV 
broadcast transmitter cannot be predicted theoretically with 
accuracy. To assess the electromagnetic environment due to 
fixed RF transmitters,...

Safety
4-22 LOGIQ E9 User Guide
Direction 5180302-100 Rev. 1
General Notice
1.  Designation of Peripheral Equipment Connectable to This 
Product.
The equipment indicated in Chapter 18 can be hooked up to 
the product without compromising its EMC performance.
Avoid using equipment not designated in the list. Failure to 
comply with this instruction may result in poor EMC 
performance of the product.
2.  Notice against User Modification
The user should never modify this product. User 
modifications may...

Safety Precautions
LOGIQ E9 User Guide 4-23
Direction 5180302-100 Rev. 1
Peripheral Update for EC countries
The following is intended to provide the users in EC countries 
with updated information concerning the connection of the 
LOGIQ E9 to image recording and other devices or 
communication networks.
The LOGIQ E9 has been verified for overall safety, compatibility 
and compliance with the following on-board image recording 
devices:
•  Sony UP-D897 Digital Printer
•  Sony UP-D23 Digital Printer
•...

Safety
4-24 LOGIQ E9 User Guide
Direction 5180302-100 Rev. 1
Peripheral Update for EC countries (continued)
Accessory equipment connected to the analog and digital 
interfaces must be certified according to the respective IEC 
standards (i.e., IEC60950 for data processing equipment and 
IEC60601-1 for medical equipment). Furthermore, all complete 
configurations shall comply with the valid version of the system 
standard IEC60601-1-1. Everyone who connects additional 
equipment to the signal input part...

Safety Precautions
LOGIQ E9 User Guide 4-25
Direction 5180302-100 Rev. 1
Peripheral Update for EC countries (continued)
General precautions for installing an alternate off-board, remote 
device or a network would include:
1.  The added device(s) must have appropriate safety standard 
conformance and CE Marking.
2.  The added device(s) must be used for their intended 
purpose having a compatible interface.
3.  Signal or mains isolation devices and additional protective 
earth may be needed to assure...

Safety
4-26 LOGIQ E9 User Guide
Direction 5180302-100 Rev. 1
Declaration of Emissions
This system is suitable for use in the following environment. The 
user must assure that it is used only in the electromagnetic 
environment as specified. 
Table 4-6:  Declaration of Emissions
Guidance and manufacturer’s declaration - electromagnetic emissions
The system is intended for use in the electrmagnetic environment specified below. The 
user of the system should assure that it is used in such an environment....

Safety Precautions
LOGIQ E9 User Guide 4-27
Direction 5180302-100 Rev. 1
Declaration of Immunity
This system is suitable for use in the following environment. The 
user must assure that the system is used according to the 
specified guidance and only in the electromagnetic environment 
listed. 

Safety
4-28 LOGIQ E9 User Guide
Direction 5180302-100 Rev. 1
Declaration of Immunity (continued)
Table 4-7:  Declaration of Immunity
Immunity Type
Equipment 
CapabilityRegulatory 
Acceptable LevelEMC Environment 
and Guidance
IEC 61000-4-2
Static discharge (ESD) ± 9 kV contact
± 12 kV air± 9 kV contact
± 12 kV airFloors should be wood, 
concrete, or ceramic tile. 
If floors are covered with 
synthetic material, the 
relative humidity should 
be at least 30%.
Mains power quality 
should be that of a...