GE I210c Manual

GE Energy
GE I-210+cElectronic Meter
Product Description and Operation, Maintenance,and Upgrade Instructions
GEH-7101-2.00-131
Daily Maximum Demand Rate A,B Time TOU Maximum Demand Time for Peaks 1 and 2 TOU
Maximum Demand Rate A,B for Peaks 1
and 2
TOU Test Mode Thermal Interval Type: “0” = 15 min.,
“1” = 1 min.
All
Maximum Demand Rate A,B Date for Peaks
1 and 2TOU Test Mode Accumulating Demand 1,2 UOM All
Maximum Demand Rate A,B Time for Peaks
1 and 2TOU Test Mode Power Factor All
Cumulative Demand...

GE I-210+cElectronic Meter
Product Description and Operation, Maintenance,and Upgrade Instructions
GE Energy
32GEH-7101-2.00-1
Time of Last Time Change TOU Current Time
TEST MODETime Remaining in Demand (Sub)interval in
minutes (Not valid for thermal demands)TOU
Test Mode Demand Interval length in
minutes (block)AllReal-Time Pricing time remaining until
activation in min.TOU/ DmdLP
Test Mode Demand No of Subintervals.
(rolling only)All
Test Mode Demand Subint. length in
minutes (rolling)All
Test Mode...

GE Energy
GE I-210+cElectronic Meter
Product Description and Operation, Maintenance,and Upgrade Instructions
GEH-7101-2.00-133
Figure 6 Alternate Display Mode Switch
3.2.1.2 Normal Display Mode
In Normal Display mode, the meter display scrolls continually through the Normal Display items
until one of the following occurs:
Demand reset is invoked.
Display Switch is actuated.
Communication is initiated.
Test mode is invoked.
A frozen error or caution message is triggered.
Note:The test mode push...

GE I-210+cElectronic Meter
Product Description and Operation, Maintenance,and Upgrade Instructions
GE Energy
34GEH-7101-2.00-1
3.2.1.3 Alternate Display Mode
The Alternate Display is used to display information for the meter technician that is not
contained in the Normal Display.
Display items:Selected during MeterMate™program development
Initiate:Actuate the display switch for more than 3 seconds.
Scroll:The meter automatically scrolls through the Alternate Display items.
Exit:The meter...

GE Energy
GE I-210+cElectronic Meter
Product Description and Operation, Maintenance,and Upgrade Instructions
GEH-7101-2.00-135
3.2.1.5 Frozen Display Mode
The Frozen Display mode stops the Normal Display to draw attention to an error, caution, or
diagnostic in the meter.
DisplayItems: Select errors, cautions, and diagnostics to freeze the display during
MeterMate™program development.
Initiate: Automatic when the meter detects a frozen error, caution, or diagnostic
Scroll: Use a magnet to activate...

GE I-210+cElectronic Meter
Product Description and Operation, Maintenance,and Upgrade Instructions
GE Energy
36GEH-7101-2.00-1
When displayed, the C annunciator indicates the C voltage is present at the meter. If this
annunciator is blinking, C voltage is low (Network meters only).
8. The left-right arrows indicate watt hour direction of energy flow. The right arrow will be lit if
the energy is delivered; the left arrow will be lit if the energy is received.
The up-down arrows indicate var hour...

GE Energy
GE I-210+cElectronic Meter
Product Description and Operation, Maintenance,and Upgrade Instructions
GEH-7101-2.00-137
3.2.3.1 kWh Display
Figure 9 kWh Display
Figure 9shows the following conditions:
The Display Label is 01.
Five-digit display of energy (kWh)
Phase A voltage is present.
End-of-demand-interval indication—This indicator is lit at the end of each demand
subinterval.
Displayed quantity is measured in kilowatt hours.
Energy is being delivered to the load.
The one block...

GE I-210+cElectronic Meter
Product Description and Operation, Maintenance,and Upgrade Instructions
GE Energy
38GEH-7101-2.00-1
3.2.3.2 Alternate Display Mode
Figure 10 Alternate Display
Figure 10shows the following conditions:
Meter is in Alternate Display mode.
Display label 108 is displayed.
Phase A and C voltages are present.
Six-digit display of quadergy (kvarh)
Displayed quantity is measured in kvarh.
The two blocks indicate State 1 of the magnitude indicator.
Quadergy (kvarh) is...

GE Energy
GE I-210+cElectronic Meter
Product Description and Operation, Maintenance,and Upgrade Instructions
GEH-7101-2.00-139
3.2.3.3 Test Mode Display
Figure 11 Test Mode Display
Figure 11shows the following conditions:
Meter is in TEST mode.
Display label is 905.
Meter display is a six-digit demand display (kW) with three digits to the right of the
decimal point.
Phase A voltage is present.
Energy is being delivered to the load.
The three blocks indicate State 2 of the magnitude...

GE I-210+cElectronic Meter
Product Description and Operation, Maintenance,and Upgrade Instructions
GE Energy
40GEH-7101-2.00-1
4 Maintenance Instructions
Warning:The information contained within this document is intended to be an aid
to qualified metering personnel. It is not intended to replace the extensive training necessary to
install or remove meters from service.Any work on or near energized meters, meter sockets,
or other metering equipment presents the danger of electrical shock.All work on...