Gateway m500 User Manual

							B
95
Safety,
Regulatory, and
Legal Information
Important safety 
information
Your Gateway system is designed and tested to meet the latest standards 
for safety of information technology equipment. However, to ensure safe 
use of this product, it is important that the safety instructions marked on 
the product and in the documentation are followed.
WarningAlways follow these instructions to help 
guard against personal injury and damage 
to your Gateway system. 
						

							96
Appendix B: Safety, Regulatory, and Legal Information
www.gateway.com
Setting up your system
■Read and follow all instructions marked on the product and in the documentation before you 
operate your system. Retain all safety and operating instructions for future use.
■D o  n o t  u s e  t h i s  p r o d u c t  n e a r  w a t e r  o r  a  h e a t  s o u r c e  s u c h  a s  a  r a d i a t o r.
■Set up the system on a stable work surface.
■The product should be operated only from the type of power source indicated on the rating label.
■If your computer has a voltage selector switch, make sure that the switch is in the proper position 
for your area. The voltage selector switch is set at the factory to the correct voltage.
■Openings in the computer case are provided for ventilation. Do not block or cover these 
openings. Make sure you provide adequate space, at least 6 inches (15 cm), around the system for 
ventilation when you set up your work area. Never insert objects of any kind into the computer 
ventilation openings.
■Some products are equipped with a three-wire power cord to make sure that the product is 
properly grounded when in use. The plug on this cord will fit only into a grounding-type outlet. 
This is a safety feature. If you are unable to insert the plug into an outlet, contact an electrician 
to install the appropriate outlet.
■If you use an extension cord with this system, make sure that the total ampere rating on the 
products plugged into the extension cord does not exceed the extension cord ampere rating.
■I f  y o u r  s y s t e m  i s  f i t t e d  w i t h  a  T V  Tu n e r,  c a b l e , or satellite receiver card, make sure that the 
antenna or cable system is electrically grounded to provide some protection against voltage 
surges and buildup of static charges.
Care during use
■D o  n o t  w a l k  o n  t h e  p o w e r  c o r d  o r  a l l o w  a n y t h i n g  t o  r e s t  o n  i t .
■Do not spill anything on the system. The best way to avoid spills is to avoid eating and drinking 
near your system.
■Some products have a replaceable CMOS battery on the system board. There is a danger of 
explosion if the CMOS battery is replaced incorrectly. Replace the battery with the same or 
equivalent type recommended by the manufacturer. Dispose of batteries according to the 
manufacturer’s instructions.
■When the computer is turned off, a small amount of electrical current still flows through the 
computer. To avoid electrical shock, always unplug all power cables and modem cables from the 
wall outlets before cleaning the system.
■Unplug the system from the wall outlet and refer servicing to qualified personnel if:
■The power cord or plug is damaged.
■Liquid has been spilled into the system.
■The system does not operate properly when the operating instructions are followed.
■The system was dropped or the cabinet is damaged.
■The system performance changes. 
						

							97
Important safety information
www.gateway.com
Replacement parts and accessories
Use only replacement parts and accessories recommended by Gateway.
ImportantDo not use Gateway products in areas classified as 
hazardous locations. Such areas include patient care 
areas of medical and dental facilities, oxygen-laden 
environments, or industrial facilities.
WarningTo reduce the risk of fire, use only No. 26 AWG or larger 
telecommunications line cord. 
						

							98
Appendix B: Safety, Regulatory, and Legal Information
www.gateway.com
Regulatory compliance 
statements
Wireless Guidance
Low power, Radio transmitting type devices (radio frequency (RF) wireless communication 
devices), may be present (embedded) in your notebook system. These devices may operate in the 
2.4 GHz (i.e. 802.11B/G LAN & Bluetooth) , 5.2 GHz (i.e. 802.11A LAN), and traditional cellular or 
PCS cellular bands (i.e. Cellular data modem). The following section is a general overview of 
considerations while operating a wireless device.
Additional limitations, cautions, and concerns for specific countries are listed in the specific 
country sections (or country group sections). The wireless devices in your system are only qualified 
for use in the countries identified by the Radio Approval Marks on the system rating label. If the 
country you will be using the wireless device in, is not listed, please contact your local Radio 
Approval agency for requirements. Wireless devices are closely regulated and use may not be 
allowed.
T h e  p o w e r  o u t p u t  o f  t h e  w i r e l e s s  d e v i c e  o r  d e v i c e s  t h a t  m a y  b e  e m b e d d e d  i n  y o u r  n o t e b o o k  i s  w e l l  
below the RF exposure limits as known at this time. Because the wireless devices (which may be 
embedded into your notebook) emit less energy than is allowed in radio frequency safety standards 
and recommendations, Gateway believes these devices are safe for use. Regardless of the power 
levels, care should be taken to minimize human contact during normal operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled 
environment of a portable device.
This transmitter must not be co-located or operating in conjunction with any other antenna or 
transmitter.
The wireless devices installed in this system are intended to be used indoors.  In some areas, use of 
these devices outdoors is prohibited.
Some circumstances require restrictions on wireless devices. Examples of common restrictions are 
listed below:
WarningRadio frequency wireless communication can interfere 
with equipment on commercial aircraft. Current aviation 
regulations require wireless devices to be turned off while 
traveling in an airplane. 802.11B (also known as wireless 
Ethernet or Wifi) and Bluetooth communication devices are 
examples of devices that provide wireless communication. 
						

							99
Regulatory compliance statements
www.gateway.com WarningIn environments where the risk of interference to other 
devices or services is harmful or perceived as harmful, the 
option to use a wireless device may be restricted or 
eliminated. Airports, Hospitals, and Oxygen or flammable 
gas laden atmospheres are limited examples where use 
of wireless devices may be restricted or eliminated. When 
in environments where you are uncertain of the sanction 
to use wireless devices, ask the applicable authority for 
authorization prior to use or turning on the wireless device.
WarningEvery country has different restrictions on the use of 
wireless devices. Since your system is equipped with a 
wireless device, when traveling between countries with 
your system, check with the local Radio Approval 
authorities prior to any move or trip for any restrictions on 
the use of a wireless device in the destination country.
WarningIf your system came equipped with an internal embedded 
wireless device, do not operate the wireless device unless 
all covers and shields are in place and the system is fully 
assembled.
WarningWireless devices are not user serviceable. Do not modify 
them in any way. Modification to a wireless device will void 
the authorization to use it. Please contact Gateway for 
service.
WarningOnly use drivers approved for the country in which the 
device will be used. See the Gateway System Restoration 
Kit, or contact Gateway Technical Support for additional 
information.
WarningIn order to comply with FCC requirements this transmitter 
must not be operated (or co-located) in conjunction with 
any other transmitter or antenna installed in the notebook. 
						

							100
Appendix B: Safety, Regulatory, and Legal Information
www.gateway.com
United States of America
Federal Communications Commission (FCC)
Intentional emitter per FCC Part 15
Low power, Radio transmitter type devices (radio frequency (RF) wireless communication devices), 
operating in the 2.4 GHz band and/or 5.15 – 5.35 GHz band, may be present (embedded) in your 
notebook system. This section is only applicable if these devices are present. Refer to the system 
label to verify the presence of wireless devices.
Wireless devices that may be in your system are only qualified for use in the United States of 
America if an FCC ID number is on the system label.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled 
environment of a portable device.
This transmitter must not be co-located or operating in conjunction with any other antenna or 
transmitter.
The wireless devices installed in this system are intended to be used indoors.  In some areas, use of 
these devices outdoors is prohibited.
Operation of this device is subject to the following two conditions: (1) This device may not cause 
harmful interference, and (2) this device must accept any interference received, including 
interference that may cause undesired operation of the device.
Unintentional emitter per FCC Part 15
This device has been tested and found to comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This equipment generates, uses, and can 
radiate radio frequency energy and, if not installed and used in accordance with the instructions, 
may cause harmful interference to radio or television reception. However, there is no guarantee 
that interference will not occur in a particular installation. If this equipment does cause 
interference to radio and television reception, which can be determined by turning the equipment 
off and on, the user is encouraged to try to correct the interference by one or more of the following 
measures:
■Reorient or relocate the receiving antenna■Increase the separation between the equipment and receiver■Connect the equipment into an outlet on a circuit different from that to which the receiver is 
connected
■Consult the dealer or an experienced radio/TV technician for help.
Compliance Accessories: The accessories associated with this equipment are: shielded video cable 
when an external monitor is connected. These accessories are required to be used in order to 
ensure compliance with FCC rules.
WarningWireless devices are not user serviceable. Do not modify 
them in any way. Modification to a wireless device will void 
the authorization to use it. Contact Gateway for service. 
						

							101
Regulatory compliance statements
www.gateway.com
FCC declaration of conformity
Responsible party:
Gateway Companies, Inc.
610 Gateway Drive, North Sioux City, SD 57049
(605) 232-2000   Fax: (605) 232-2023
Product:
■M500B1
This device complies with Part 15 of the FCC Rules. Operation of this product is subject to the 
following two conditions: (1) this device may not cause harmful interference, and (2) this device 
must accept any interference received, including interference that may cause undesired operation.
CautionChanges or modifications not expressly approved by 
Gateway could void the FCC compliance and negate your 
authority to operate the product. 
						

							102
Appendix B: Safety, Regulatory, and Legal Information
www.gateway.com
Telecommunications per FCC part 68 
(applicable to products fitted with USA modems)
Your modem complies with Part 68 of the Federal Communications Commission (FCC) rules. On 
the computer or modem card is a label that contains the FCC registration number and Ringer 
Equivalence Number (REN) for this device. If requested, this information must be provided to the 
telephone company.
An FCC-compliant telephone line cord with a modular plug is required for use with this device. 
The modem is designed to be connected to the telephone network or premises wiring using a 
compatible modular jack which is Part 68-compliant. See installation instructions for details.
The Ringer Equivalence Number (REN) is used to determine the number of devices which may be 
connected to the telephone line. Excessive RENs on a telephone line may result in the devices not 
ringing in response to an incoming call. In most areas, the sum of RENs should not exceed five 
(5.0). To be certain of the number of devices that may be connected to a line, as determined by the 
total RENs, contact the local telephone company.
If this device causes harm to the telephone network, the telephone company will notify you in 
advance that temporary discontinuance of service may be required. The telephone company may 
request that you disconnect the equipment until the problem is resolved.
The telephone company may make changes in its facilities, equipment, operations, or procedures 
that could affect the operation of this equipment. If this happens, the telephone company will 
provide advance notice in order for you to make necessary modifications to maintain 
uninterrupted service.
This equipment cannot be used on telephone company-provided coin service. Connection to party 
line service is subject to state tariffs. Contact the state public utility commission or public service 
commission for information.
When programming or making test calls to emergency numbers:
■Remain on the line and briefly explain to the dispatcher the reason for the call.■Perform such activities in the off-peak hours such as early morning or late evenings.
The United States Telephone Consumer Protection Act of 1991 makes it unlawful for any person to 
use a computer or other electronic device to send any message via a telephone fax machine unless 
such message clearly contains, in a margin at the top or bottom of each transmitted page or on the 
first page of the transmission, the date and time it is sent, an identification of the business, other 
entity, or other individual sending the message, and the telephone number of the sending 
machine or such business, other entity, or individual. Refer to your fax communication software 
documentation for details on how to comply with the fax-branding requirement. 
						

							103
Regulatory compliance statements
www.gateway.com
Laser safety statement
All Gateway systems equipped with CD and DVD drives comply with the appropriate safety 
standards, including IEC 825. The laser devices in these components are classified as “Class 1 Laser 
Products” under a US Department of Health and Human Services (DHHS) Radiation Performance 
Standard. Should the unit ever need servicing, contact an authorized service location.
California Proposition 65 Warning
WarningUse of controls or adjustments or performance of 
procedures other than those specified in this manual may 
result in hazardous radiation exposure. To prevent 
exposure to laser beams, do not try to open the enclosure 
of a CD or DVD drive.
WarningThis product contains chemicals, including lead, known to 
the State of California to cause cancer and/or birth defects 
or reproductive harm. 
						

							104
Appendix B: Safety, Regulatory, and Legal Information
www.gateway.com
Notices
Copyright © 2003 Gateway, Inc.
All Rights Reserved
14303 Gateway Place
Poway, CA 92064 USA
All Rights Reserved
This publication is protected by copyright and all rights are reserved. No part of it may be reproduced or 
transmitted by any means or in any form, without prior consent in writing from Gateway.
The information in this manual has been carefully checked and is believed to be accurate. However, changes are 
made periodically. These changes are incorporated in newer publication editions. Gateway may improve and/or 
change products described in this publication at any time. Due to continuing system improvements, Gateway is 
not responsible for inaccurate information which may appear in this manual. For the latest product updates, 
consult the Gateway Web site at www.gateway.com
. In no event will Gateway be liable for direct, indirect, special, 
exemplary, incidental, or consequential damages resulting from any defect or omission in this manual, even if 
advised of the possibility of such damages.
In the interest of continued product development, Gateway reserves the right to make improvements in this 
manual and the products it describes at any time, without notices or obligation.
Trademark Acknowledgments
1-800-GATEWAY, ActiveCPR, ALR, AnyKey, black-and-white spot design, CrystalScan, Destination, DestiVu, EZ 
Pad, EZ Point, Field Mouse, Gateway 2000, Gateway Country, gateway.net, Gateway stylized logo, Perfect 
Scholar, Solo, TelePath, Vivitron, stylized “G” design, and “You’ve got a friend in the business” slogan are 
registered trademarks and black-and-white spotted box logo, GATEWAY, Gateway Astro, Gateway@Work, 
Gateway Connected touch pad, Gateway Connected music player, Gateway Cyber:)Ware, Gateway 
Education:)Ware, Gateway Flex Case, Gateway Gaming:)Ware, Gateway GoBack, Gateway Gold, Gateway 
Learning:)Ware, Gateway Magazine, Gateway Micro Server, Gateway Money:)Ware, Gateway Music:)Ware, 
Gateway Networking Solutions, Gateway Online Network (O.N.) solution, Gateway Photo:)Ware, Gateway 
Professional PCs, Gateway Profile, Gateway Solo, green stylized GATEWAY, green stylized Gateway logo, 
Gateway Teacher:)Ware, Gateway Video:)Ware, HelpSpot, InforManager, Just click it!, Learn@Gateway, Kids 
BackPack, SERVE-TO-ORDER, Server Watchdog, the Spotted G Gateway Logo and the Spotted G Logo, 
SpotShop, Spotshop.com, and Your:)Ware are trademarks of Gateway, Inc. Intel, Intel Inside logo, and Pentium 
are registered trademarks and MMX is a trademark of Intel Corporation. Microsoft, MS, MS-DOS, and Windows 
are trademarks or registered trademarks of Microsoft Corporation. All other product names mentioned herein are 
used for identification purposes only, and may be the trademarks or registered trademarks of their respective 
companies.
Macrovision statement
If your computer has a DVD drive and an analog TV Out port, the following paragraph applies:
This product incorporates copyright protection technology that is protected by method claims of certain U.S. 
patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of 
this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home 
and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse 
engineering or disassembly is prohibited.