Gateway M465e Service Manual

							Preparing the notebook www.gateway.com
7
3Slide the battery release latch, then slide the battery out of the notebook.
Removing the optional secondary battery
To remove the optional secondary battery:  
1Remove the security screw if your notebook has one.
2Slide the bay module release latch. The secondary battery moves out 
slightly.
3Slide the secondary battery out.
Security screw 
						

							Replacing Gateway Notebook Componentswww.gateway.com
8
Adding or replacing memory modules
ImportantUse only memory modules designed for
this Gateway notebook.Tools you need to complete this task:
Screws removed during this task:
Phillips #0 screwdriver
1 black (keyboard)
Memory bay 
						

							Adding or replacing memory modules www.gateway.com
9
To add or replace memory modules:  
1Complete the steps in “Preparing the notebook” on page 5.
Tips & TricksThe screw hole is marked with a K.2Remove the keyboard screw.
3Loosen the six memory bay cover screws (these screws cannot be 
removed).
4Use the thumb notch to lift the memory bay cover, then remove it. Be 
careful not to break off the tabs located on the end of the cover opposite 
of the thumb notch.
Screw
Screws 
						

							Replacing Gateway Notebook Componentswww.gateway.com
10
5If you are removing a module, gently press outward on the clip at each 
end of the memory module until the module tilts upward.
6Pull the memory module out of the slot. 
						

							Adding or replacing memory modules www.gateway.com
11
7Hold the new or replacement module at a 30-degree angle and press it 
into the empty memory slot. This module is keyed so it can only be 
inserted in one direction. If the module does not fit, make sure that the 
notch in the module lines up with the tab in the memory bay.
8Replace the memory bay cover, then tighten the cover screws.
Tips & TricksThe screw hole is marked with a K.9Replace the keyboard screw. 
						

							Replacing Gateway Notebook Componentswww.gateway.com
12
Replacing the cooling assembly
Tools you need to complete this task:
Additional materials you need to complete this task:
■X-23-7762 thermal grease
Screws removed during this task:
To replace the cooling assembly:  
1Complete the steps in “Preparing the notebook” on page 5.
Tips & TricksThe screw hole is marked with a K.2Remove the keyboard screw.
Phillips #0 screwdriver
1 black (keyboard)
Screw 
						

							Replacing the cooling assembly www.gateway.com
13
3Loosen the six memory bay cover screws (these screws cannot be 
removed), then remove the memory bay cover.
4Use the thumb notch to lift the memory bay cover, then remove it. Be 
careful not to break off the tabs located on the end of the cover opposite 
of the thumb notch.
CautionWhen loosening the cooling assembly’s
screws in the numbered holes, loosen
them in reverse numerical order.
ImportantThe number of screws varies by model.
5Loosen the three or four screws (these screws cannot be removed) that 
secure the cooling assembly to the system board. Use the numbers 
stamped in the metal next to each screw and loosen the screws in reverse 
numerical order (start with 4, then 3, then 2, then 1).
Screws
Screw Screw
Screw
Screw 
						

							Replacing Gateway Notebook Componentswww.gateway.com
14
CautionThe cooling assembly cable is attached to
the system board at this point. Be careful
not to break the cable.6At the same time as you lift, move the cooling assembly away from the 
side of the notebook.
7Unplug the old cooling fan, then remove the cooling assembly.
8Remove any thermal grease residue from the processor using a soft cloth 
and isopropyl alcohol.
9Place new thermal grease on the processor. Use only enough to cover the 
CPU die.
10Plug in the new cooling fan.
11Insert the new cooling assembly into the notebook.
CautionWhen tightening the cooling assembly’s
screws into the numbered holes, tighten
them in numerical order.12Tighten the three or four screws that secure the cooling assembly to the 
system board. Use the numbers stamped in the metal next to each screw 
and tighten the screws in numerical order (start with 1, then 2, then 3, 
then 4).
13Replace the memory bay cover, then tighten the cover screws.
Tips & TricksThe screw hole is marked with a K.14Replace the keyboard screw.
Connector 
						

							Replacing the processor www.gateway.com
15
Replacing the processor
Tools you need to complete this task:
Additional materials you need to complete this task:
■X-23-7762 thermal grease
Screws removed during this task:
To replace the processor:  
1Complete the steps in “Preparing the notebook” on page 5.
2Remove the cooling assembly by following the instructions in “Replacing 
the cooling assembly” on page 12.
Phillips #0 screwdriver
1 black (keyboard) 
						

							Replacing Gateway Notebook Componentswww.gateway.com
16
3Use a flat-blade screwdriver to turn the processor lock screw 1/4-turn 
counter-clockwise.
Screw