Gateway m350 User Manual

							151
Automatically cancelling a fax in Windows XP
www.gateway.com
5Specify the number of retries and the amount of time between retries.
6Click OK.
Automatically cancelling a fax in 
Windows XP
If your notebook tried to send a fax and failed to connect to a fax machine, 
you can automatically cancel a failed fax.
To automatically cancel a failed fax in Windows XP:
1Click Start, then click Control Panel. The Control Panel window opens.
2If your Control Panel is in Category View, click Printers and Other Hardware. 
Click 
View installed printers or fax printers. The Printers and Faxes window 
opens.
-OR-
If your Control Panel is in Classic View, double-click the 
Printers and Faxes 
icon. The Printers and Faxes window opens.
3Right-click Fax, then click Properties. The Fax Properties dialog box opens.
4Click the Devices tab, then click Properties. The Modem dialog box opens.
5Click the Cleanup tab.
6Click to select the Automatically delete failed faxes after check box and specify 
the number of days.
7Click OK. 
						

							152
Chapter 7: Sending and Receiving Faxes
www.gateway.com 
						

							8
153
Managing Power
While your notebook is running on battery power, you 
should manage power consumption to get the most use out 
of the battery. Read this chapter to learn how to:
■Check and recharge the battery
■Recalibrate the battery
■Change batteries
■Extend the life of the battery by conserving battery 
power and using alternate power sources
■Change power-saving settings 
						

							154
Chapter 8: Managing Power
www.gateway.com
Monitoring the battery charge
Closely monitor the battery charge. When the battery charge gets low, change 
the battery or connect to AC power immediately to prevent losing any unsaved 
work.
Monitor the battery charge by:
■Double-clicking the power cord icon  or battery icon  in the taskbar. 
The Power Meter dialog box opens.
■Pressing FN+STATUS to view the power status box, which opens in the 
upper-left corner of the screen. The power status box shows the current 
power source, the battery charge level, and the power management mode.
■Looking at the battery charge indicator:
■LED green - battery is fully charged.
■LED orange - battery is charging.
■LED blinking red - battery charge is very low.
■LED solid red - battery is malfunctioning.
■Waiting for a Low Battery warning message to appear.
If your battery charge indicator displays what looks like an inaccurate charge, 
you may need to recalibrate the battery. For more information, see 
“Recalibrating the battery” on page 156.
ImportantIf the power cord or battery icon does not appear on the 
taskbar, click the show hidden icons button. If the icon 
still does not appear, make sure that Always show icon 
on the taskbar is checked on the Power Options 
Properties Advanced tab. See “Changing advanced 
settings” on page 164 for more information.
ImportantThis LED only lights up when your notebook is connected 
to AC power or the battery charge is very low. For the 
location of the battery charge indicator, see “Front” on 
page 2. 
						

							155
Recharging the battery
www.gateway.com
Recharging the battery
The battery recharges while it is installed and your notebook is connected to 
AC power. While the battery is recharging, the battery charge indicator turns 
orange and the battery icon in the taskbar has a lightning bolt .
ImportantIf the power cord or battery icon does not appear on the 
taskbar, click the show hidden icons button. If the icon 
still does not appear, make sure that Always show icon 
on the taskbar is checked on the Power Options 
Properties Advanced tab. See “Changing advanced 
settings” on page 164 for more information. 
						

							156
Chapter 8: Managing Power
www.gateway.com
Recalibrating the battery
If your notebook unexpectedly goes into Standby mode while you are using it 
but the battery charge is not low, you may need to recalibrate your battery. 
You should also recalibrate the battery periodically to maintain the accuracy 
of the battery gauge.
To recalibrate the battery:
1Connect the AC adapter, then turn on your notebook.
2As soon as it starts and you see a startup screen, press F2. The BIOS Setup 
utility opens.
3Open the Advanced menu.
4Highlight Battery Auto Learning, then select Enabled by pressing the 
spacebar.
5Open the Exit menu, then highlight Exit Saving Changes and press ENTER.
6Select Yes, then press ENTER.
The battery recalibration process begins and a screen opens showing you 
the progress. The entire process will take several hours.
When the recalibration has finished, the message “Press [Esc] key to exit” 
appears.
7Press ESC. The battery charge indicator now displays an accurate battery 
charge. If the battery charge indicator does not show an accurate charge, 
contact Gateway Technical Support.
ImportantDo not interrupt the battery recalibration process. If 
recalibration is interrupted, you must start the process over 
again. 
						

							157
Changing batteries
www.gateway.com
Changing batteries
If your notebook is plugged into an AC outlet, you can change the battery while 
your notebook is turned on. If your notebook is not plugged into an AC outlet, 
you must turn your notebook off while changing the battery.
Replacing the battery
To replace the battery:
1If your notebook is on and is connected to AC power, go to Step 2.
-OR-
If your notebook is on and is not connected to AC power, save your work 
and turn off your notebook.
2Close the LCD panel.
3Turn your notebook over so the bottom is facing up.
WarningDanger of explosion if battery is incorrectly replaced.
Replace only with a Gateway M350 battery. Discard used 
batteries according to the manufacturer’s instructions.
The battery used in this device may present a fire or 
chemical burn hazard if mishandled. Do not disassemble, 
heat above 212°F (100°C), or incinerate. Dispose of used 
battery promptly. Keep away from children. 
						

							158
Chapter 8: Managing Power
www.gateway.com
4Slide the battery release latch.
5Lift the battery out of the bay.
6Place a recharged battery into the bay and press down until it snaps into 
place.
7Turn your notebook over.
8Open the LCD panel and press the power button. 
						

							159
Extending battery life
www.gateway.com
Extending battery life
Conserving battery power
While using the battery to power your notebook, conserve power by:
■Dimming the display as low as is comfortable.
■Removing PC Cards and IBM Microdrive cards when you do not need 
them. Many PC Cards and Microdrive cards use a small amount of power 
while inserted, even if they are not being used.
■Modifying the power management settings for maximum power savings. 
For more information, see “Changing power settings” on page 161.
■Closing the LCD panel to turn off the display while you are not using your 
notebook. The display stays off until you open the panel again.
■Using Hibernate mode for maximum power savings while your notebook 
is not in use. For more information, see “Activating and using Hibernate 
mode” on page 165.
■Using the CD, DVD, or recordable drive only when necessary. These drives 
use a large amount of power.
■Recharging the battery often, taking an extra battery, and fully recharging 
the batteries before traveling. For more information, see “Recharging the 
battery” on page 155 and “Changing batteries” on page 157.
Using alternate power sources
To extend battery life, use alternate power sources whenever possible.
■If traveling internationally, take electrical adapters. Save the battery for 
times when you cannot use a power adapter. If you plan on taking your 
AC power adapter, also take a single-plug surge protector.
■If you will have access to an automobile cigarette lighter, use a power 
inverter. Save the battery for times when you cannot use a power adapter.
■To find AC power outlets in airports, look for them next to support pillars, 
in large areas such as boarding gates, and under banks of telephones. 
						

							160
Chapter 8: Managing Power
www.gateway.com
Changing power modes
You can use the following power modes to lengthen the life of your notebook’s 
battery:
■Standby - while your notebook is in Standby, it switches to a low power 
state where devices, such as the display and drives, turn off.
■Hibernate - (also called save to disk) writes all current memory (RAM) 
information to the hard drive, then turns your notebook completely off. 
The next time you turn on your notebook, it reads the memory 
information from the hard drive and opens the programs and documents 
that were open when you activated Hibernate mode. For more information 
on using Hibernate mode, see “Activating and using Hibernate mode” on 
page 165.
Using power saving modes
Always save your work before using Standby mode. In Standby mode, your 
notebook reduces or turns off the power to most devices except memory. 
However, the information in memory is not saved to the hard drive. If power 
is interrupted, the information is lost.
When in Hibernate mode, your notebook saves all memory information to the 
hard drive, then turns the power completely off.
If your notebook 
is......and you want to... ...then
On Enter Standby mode Press FN+STANDBY.
-OR-
Close the LCD panel.
On Enter Hibernate mode 
(must be activated)In Windows XP, click Start, then click 
Tu r n O f f C o m p u t e r. Press and hold 
SHIFT, then 
click Hibernate.
- OR -
In Windows 2000, click Start, then click Shut 
Down. Click the arrow button to open the What do 
you want your computer to do list, then click 
Hibernate. Click OK.
In Standby or 
Hibernate modeExit Standby or 
Hibernate modePress the power button.