Gateway E-475m Manual

							APPENDIXA
123
Legal Information
•Important safety information
•Regulatory compliance statements
•Environmental information
•Notices 
						

							APPENDIXA: Legal Information
124
Important safety information
Your Gateway notebook is designed and tested to meet the latest standards for safety of 
information technology equipment. However, to ensure safe use of this notebook, it is important 
that the safety instructions marked on the notebook and in the documentation are followed.
Setting up your system
•Read and follow all instructions marked on the notebook and in the documentation 
before you operate your notebook. Retain all safety and operating instructions for 
future use.
•Do not use this notebook near water or a heat source such as a radiator.•Set up the notebook on a stable work surface.•The notebook should be operated only from the type of power source indicated on 
the rating label.
•Openings in the notebook case are provided for ventilation. Do not block or cover these 
openings. Make sure you provide adequate space, at least 6 inches (15 cm), around the 
notebook for ventilation when you set up your work area. Never insert objects of any 
kind into the notebook ventilation openings.
•Some notebook are equipped with a three-wire power cord to make sure that the 
notebook is properly grounded when in use. The plug on this cord will fit only into a 
grounding-type outlet. This is a safety feature. If you are unable to insert the plug into 
an outlet, contact an electrician to install the appropriate outlet.
•If you use an extension cord with this notebook, make sure that the total ampere rating 
on the products plugged into the extension cord does not exceed the extension cord 
ampere rating.
•If your notebook is fitted with a TV Tuner, cable, or satellite receiver card, make sure 
that the antenna or cable system is electrically grounded to provide some protection 
against voltage surges and buildup of static charges.
Care during use
•Do not walk on the power cord or allow anything to rest on it.•Do not spill anything on the notebook. The best way to avoid spills is to avoid eating 
and drinking near your notebook.
•Some notebooks have a replaceable CMOS battery on the system board. There is a 
danger of explosion if the CMOS battery is replaced incorrectly. Replace the battery 
with the same or equivalent type recommended by the manufacturer. Dispose of 
batteries according to the manufacturer’s instructions.
•When the notebook is turned off, a small amount of electrical current still flows through 
the notebook. To avoid electrical shock, always unplug all power cables and modem 
cables from the wall outlets before cleaning the notebook.
War ningAlways follow these instructions to help guard against personal injury 
and damage to your Gateway system.
War ningDo not use Gateway products in areas classified as hazardous locations. 
Such areas include patient care areas of medical and dental facilities, 
oxygen-laden environments, or industrial facilities.
War ningTo reduce the risk of fire, use only No. 26 AWG or larger (for example, 
No. 24 AWG) UL-listed or CSA-certified telecommunication line cord for your 
dialup modem connection. 
						

							www.gateway.com
125
•Unplug the notebook from the wall outlet and refer servicing to qualified personnel if:•The power cord or plug is damaged.•Liquid has been spilled into the notebook.•The notebook does not operate properly when the operating instructions are 
followed.
•The notebook was dropped or the cabinet is damaged.•The notebook performance changes.
Replacement parts and accessories
Use only replacement parts and accessories recommended by Gateway.
Regulatory compliance 
statements
Wireless guidance
Low power, Radio transmitting type devices (radio frequency (RF) wireless communication 
devices), may be present (embedded) in your notebook system. These devices may operate in 
the 2.4 GHz (i.e. 802.11b/g LAN & Bluetooth), 5.2 GHz (i.e. 802.11a LAN), and traditional cellular 
or PCS cellular bands (i.e. Cellular data modem). The following section is a general overview of 
considerations while operating a wireless device.
War ningRadio frequency wireless communication can interfere with equipment 
on commercial aircraft. Current aviation regulations require wireless devices to 
be turned off while traveling in an airplane. IEEE 802.11 (also known as wireless 
Ethernet or WiFi), wireless Internet, and Bluetooth communication devices are 
examples of devices that provide wireless communication.
War ningIn environments where the risk of interference to other devices or 
services is harmful or perceived as harmful, the option to use a wireless device 
may be restricted or eliminated. Airports, Hospitals, and Oxygen or flammable 
gas laden atmospheres are limited examples where use of wireless devices may 
be restricted or eliminated. When in environments where you are uncertain of 
the sanction to use wireless devices, ask the applicable authority for 
authorization prior to use or turning on the wireless device.
War ningIf your notebook came equipped with an internal embedded wireless 
device, do not operate the wireless device unless all covers and shields are in 
place and the notebook is fully assembled.
CautionWireless devices are not user serviceable. Do not modify them in any way. 
Modification to a wireless device will void the authorization to use it. Please 
contact Gateway for service. 
						

							APPENDIXA: Legal Information
126
Additional limitations, cautions, and concerns for specific countries are listed in the specific 
country sections (or country group sections). The wireless devices in your system are only 
qualified for use in the countries identified by the Radio Approval Marks on the system rating 
label. If the country you will be using the wireless device in, is not listed, please contact your 
local Radio Approval agency for requirements. Wireless devices are closely regulated and use 
may not be allowed.
The power output of the wireless device or devices that may be embedded in your notebook 
is well below the RF exposure limits as known at this time. Because the wireless devices (which 
may be embedded into your notebook) emit less energy than is allowed in radio frequency safety 
standards and recommendations, Gateway believes these devices are safe for use. Regardless 
of the power levels, care should be taken to minimize human contact during normal operation.
Measurements have been performed to show that the RF exposure is below what is considered 
safe limits; however care should be taken to make sure the user or bystanders keep the 
transmitter away from their body when the wireless device is transmitting. The transmitting 
antenna installed in the top third of the lid should be used in a manner to maintain 8 inches 
(20 cm) from user’s or bystander’s bodies.
The wireless devices installed in this system are intended to be used indoors. In some areas, 
use of these devices outdoors is prohibited.
Some circumstances require restrictions on wireless devices.
United States of America
Federal Communications Commission (FCC) 
Intentional emitter per FCC Part 15
Low power, Radio transmitter type devices (radio frequency (RF) wireless communication 
devices), operating in the 2.4 GHz band and/or 5.15 – 5.35 GHz band, may be present (embedded) 
in your notebook system. This section is only applicable if these devices are present. Refer to 
the system label to verify the presence of wireless devices.
Wireless devices that may be in your system are only qualified for use in the United States of 
America if an FCC ID number is on the system label.
CautionOnly use drivers approved for the country in which the device will be 
used. See the Gateway System Restoration Kit, or contact Gateway Customer 
Care for additional information.
ImportantEvery country has different restrictions on the use of wireless devices. 
Since your notebook is equipped with a wireless device, when traveling 
between countries with your notebook, check with the local Radio Approval 
authorities prior to any move or trip for any restrictions on the use of a wireless 
device in the destination country.
CautionWireless devices are not user-serviceable. Do not modify them in any 
way. Modification to a wireless device will void the authorization to use it. 
Contact Gateway for service.
CautionThe transmitting device embedded in this notebook may not be used 
with any antenna other than the one provided with the notebook.
CautionIn order to comply with FCC requirements this transmitter must not be 
operated (or co-located) in conjunction with any other transmitter or antenna 
installed in the notebook. 
						

							www.gateway.com
127
The FCC has set a general guideline of 8 inches (20 cm) separation between the device and the 
body, for use of a wireless device near the body (this does not include extremities). This device 
should be used more than 8 inches (20 cm) from the body when wireless devices are on. The 
power output of the wireless device (or devices), which may be embedded in your notebook, 
is well below the RF exposure limits as set by the FCC.
The wireless devices installed in this system are intended to be used indoors. In some areas, 
use of these devices outdoors is prohibited.
Operation of this device is subject to the following two conditions: (1) This device may not cause 
harmful interference, and (2) this device must accept any interference received, including 
interference that may cause undesired operation of the device.
Unintentional emitter per FCC Part 15
This device has been tested and found to comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This equipment generates, uses, and 
can radiate radio frequency energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio or television reception. However, there is 
no guarantee that interference will not occur in a particular installation. If this equipment does 
cause interference to radio and television reception, which can be determined by turning the 
equipment off and on, the user is encouraged to try to correct the interference by one or more 
of the following measures:
•Reorient or relocate the receiving antenna•Increase the separation between the equipment and receiver•Connect the equipment into an outlet on a circuit different from that to which the 
receiver is connected
•Consult the dealer or an experienced radio/TV technician for help.Compliance accessories: The accessories associated with this equipment are: shielded 
video cable when an external monitor is connected. These accessories are required to be used 
in order to ensure compliance with FCC rules.
FCC declaration of conformity
Responsible party:Gateway, Inc.
7565 Irvine Center Drive
Irvine, CA 92618
Phone: 800-846-2000
Product:
•NA1•QA1
This device complies with Part 15 of the FCC Rules. Operation of this product is subject to the 
following two conditions: (1) this device may not cause harmful interference, and (2) this device 
must accept any interference received, including interference that may cause undesired 
operation.
CautionChanges or modifications not expressly approved by Gateway could void 
the FCC compliance and negate your authority to operate the notebook.
CautionRecycle or dispose of the used notebook properly according to federal, 
state and local laws. 
						

							APPENDIXA: Legal Information
128
California Proposition 65 Warning
Mercury Warning
Telecommunications per Part 68 of the Code of 
Federal Regulations (CFR 47) (applicable to products 
fitted with USA modems)
Your modem complies with Part 68 of the Code of Federal Regulations (CFR 47) rules. On the 
computer or modem card is a label that contains the FCC registration number and Ringer 
Equivalence Number (REN) for this device. If requested, this information must be provided to 
the telephone company.
A telephone line cord with a modular plug is required for use with this device. The modem is 
designed to be connected to the telephone network or premises wiring using a compatible 
modular jack which is Part 68-compliant. See installation instructions for details.
The Ringer Equivalence Number (REN) is used to determine the number of devices which may 
be connected to the telephone line. Excessive RENs on a telephone line may result in the devices 
not ringing in response to an incoming call. In most areas, the sum of RENs should not exceed 
five (5). To be certain of the number of devices that may be connected to a line, as determined 
by the total RENs, contact the local telephone company.
If this device causes harm to the telephone network, the telephone company will notify you in 
advance that temporary discontinuance of service may be required. The telephone company may 
request that you disconnect the equipment until the problem is resolved.
The telephone company may make changes in its facilities, equipment, operations, or procedures 
that could affect the operation of this equipment. If this happens, the telephone company will 
provide advance notice in order for you to make necessary modifications to maintain 
uninterrupted service.
This equipment cannot be used on telephone company-provided coin service. Connection to 
party line service is subject to state tariffs. Contact the state public utility commission or public 
service commission for information.
When programming or making test calls to emergency numbers:
•Remain on the line and briefly explain to the dispatcher the reason for the call.•Perform such activities in the off-peak hours such as early morning or late evenings.
The United States Telephone Consumer Protection Act of 1991 makes it unlawful for any person 
to use a computer or other electronic device to send any message via a telephone fax machine 
unless such message clearly contains, in a margin at the top or bottom of each transmitted page 
or on the first page of the transmission, the date and time it is sent, an identification of the 
business, other entity, or other individual sending the message, and the telephone number of 
the sending machine or such business, other entity, or individual. Refer to your fax 
communication software documentation for details on how to comply with the fax-branding 
requirement.
War ningThis product contains chemicals, including lead, known to the State of 
California to cause cancer, birth defects or reproductive harm.
Warning
The lamp in this display contains mercury. Do not put in trash. Recycle 
or dispose as hazardous waste
Hg 
						

							www.gateway.com
129
Canada
Industry Canada (IC) Intentional emitter per RSS 210
Low power, Radio transmitter type devices (radio frequency (RF) wireless communication 
devices), operating in the 2.4 GHz band and/or 5.15 – 5.35 GHz band, may be present (embedded) 
in your notebook system. This section is only applicable if these devices are present. Refer to 
the system label to verify the presence of wireless devices.
Wireless devices that may be in your system are only qualified for use in Canada if an Industry 
Canada ID number is on the system label.
As a general guideline, a separation of 8 inches (20 cm) between the wireless device and the 
body, for use of a wireless device near the body (this does not include extremities) is typical. 
This device should be used more than 8 inches (20 cm) from the body when wireless devices 
are on. The power output of the wireless device (or devices), which may be embedded in your 
notebook, is well below the RF exposure limits as set by Industry Canada. 
Operation of this device is subject to the following two conditions: (1) This device may not cause 
harmful interference, and (2) this device must accept any interference received, including 
interference that may cause undesired operation of the device.
Unintentional emitter per ICES-003
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital 
apparatus as set out in the radio interference regulations of Industry Canada.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites 
applicables aux appareils numériques de Classe B prescrites dans le règlement sur le brouillage 
radioélectrique édicté par Industrie Canada.
Telecommunications per Industry Canada CS-03 (for 
products fitted with an IC-compliant modem)
The Industry Canada label identifies certified equipment. This certification means that the 
equipment meets certain telecommunications network protective, operation, and safety 
requirements. The Department does not guarantee the equipment will operate to the users’ 
satisfaction.
CautionTo prevent radio interference to licensed service or co-channel Mobile 
Satellite systems, this device is intended to be operated indoors and away from 
windows to provide maximum shielding. Equipment (or its transmit antenna) 
that is installed outdoors is subject to licensing.
CautionWireless devices are not user-serviceable. Do not modify them in any 
way. Modification to a wireless device will void the authorization to use it. 
Contact Gateway for service.
CautionThe transmitting device embedded in this notebook may not be used 
with any antenna other than provide with the notebook.
CautionThe 802.11A radio LAN your notebook may have been equipped with 
operates in the same frequency range as high power radar, which has priority 
use, and may damage the radio LAN if both are present and being used in the 
same area. 
						

							APPENDIXA: Legal Information
130
Before installing this equipment, users should make sure that it is permissible to be connected 
to the facilities of the local telecommunications company. The equipment must also be installed 
using an acceptable method of connection. In some cases, the inside wiring associated with a 
single-line individual service may be extended by means of a certified connector assembly. The 
customer should be aware that compliance with the above conditions may not prevent 
degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility 
designated by the supplier. Any repairs or alterations made by the user to this equipment, or 
equipment malfunctions, may give the telecommunications company cause to request the user 
to disconnect the equipment.
Users should make sure, for their own protection, that the electrical ground connections of the 
power utility, telephone lines, and internal metallic water pipe system, if present, are connected 
together. This precaution may be particularly important in rural areas.
The 
Ringer Equivalence Number (REN) assigned to each terminal device provides an 
indication of the maximum number of terminals allowed to be connected to a telephone 
interface. The termination on an interface may consist of any combination of devices subject 
only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does 
not exceed 5.
Japan
Japanese Modem Notice
Laser safety statement
War ningTo avoid electrical shock or equipment malfunction do not attempt to 
make electrical ground connections by yourself. Contact the appropriate 
inspection authority or an electrician, as appropriate.
War ningUse of controls or adjustments or performance of procedures other than 
those specified in this manual may result in hazardous radiation exposure. To 
prevent exposure to laser beams, do not try to open the enclosure of a CD or 
DVD drive. 
						

							www.gateway.com
131
All Gateway systems equipped with CD and DVD drives comply with the appropriate safety 
standards, including IEC 825. The laser devices in these components are classified as “Class 1 
Laser Products” under a US Department of Health and Human Services (DHHS) Radiation 
Performance Standard. Should the unit ever need servicing, contact an authorized service 
location.
EPA ENERGY STAR
As an ENERGY STAR® Partner, Gateway has 
determined that this product meets the 
ENERGY STAR guidelines for energy efficiency 
when used with a computer equipped with a 
Display Power Management System.
Environmental information
The product you have purchased contains extracted natural resources that have been used in 
the manufacturing process. This product may contain substances known to be hazardous to the 
environment or to human health.
To prevent releases of harmful substances into the environment and to maximize the use of our 
natural resources, Gateway provides the following information on how you can responsibly 
recycle or reuse most of the materials in your “end of life” product.
Waste Electrical and Electronic Equipment (commonly
known as WEEE) should never be disposed of in the 
municipal waste stream (residential garbage 
collection). The “Crossed-Out Waste Bin” label affixed
to this product is your reminder to dispose of your “end of life” product properly.
Substances such as glass, plastics, and certain chemical compounds are highly recoverable, 
recyclable, and reusable. You can do your part for the environment by following these simple 
steps:
•When your electrical or electronic equipment is no longer useful to you, “take it back” 
to your local or regional waste collection administration for recycling.
•In some cases, your “end of life” product may be “traded in” for credit towards the 
purchase of new Gateway equipment. Call Gateway to see if this program is available 
in your area.
•If you need further assistance in recycling, reusing, or trading in your “end of life” 
product, you may contact us at the Customer Care number listed in your product’s 
user guide and we will be glad to help you with your effort.
Finally, we suggest that you practice other environmentally friendly actions by understanding 
and using the energy-saving features of this product (where applicable), recycling the inner and 
outer packaging (including shipping containers) this product was delivered in, and by disposing 
of or recycling used batteries properly.
With your help, we can reduce the amount of natural resources needed to produce electrical 
and electronic equipment, minimize the use of landfills for the disposal of “end of life” products, 
and generally improve our quality of life by ensuring that potentially hazardous substances are 
not released into the environment and are disposed of properly.
ENERGY STAR 
						

							APPENDIXA: Legal Information
132
Notices
Copyright © 2007 Gateway, Inc.
All Rights Reserved
7565 Irvine Center Drive
Irvine, CA 92618 USA
All Rights Reserved
This publication is protected by copyright and all rights are reserved. No part of it may be 
reproduced or transmitted by any means or in any form, without prior consent in writing from 
Gateway.
The information in this manual has been carefully checked and is believed to be accurate. 
However, changes are made periodically. These changes are incorporated in newer publication 
editions. Gateway may improve and/or change products described in this publication at any time. 
Due to continuing system improvements, Gateway is not responsible for inaccurate information 
which may appear in this manual. For the latest product updates, consult the Gateway Web site 
at 
www.gateway.com. In no event will Gateway be liable for direct, indirect, special, 
exemplary, incidental, or consequential damages resulting from any defect or omission in this 
manual, even if advised of the possibility of such damages.
In the interest of continued product development, Gateway reserves the right to make 
improvements in this manual and the products it describes at any time, without notices or 
obligation.
Trademark Acknowledgments
Gateway and the Black-and-White Spot Design are trademarks or registered trademarks of 
Gateway, Inc. in the U.S. and other countries. Intel, Intel Inside logo, and Pentium are registered 
trademarks of Intel Corporation. Microsoft, MS, and Windows are trademarks or registered 
trademarks of Microsoft Corporation. All other product names mentioned herein are used for 
identification purposes only, and may be the trademarks or registered trademarks of their 
respective companies.
Macrovision statement
If your notebook has a DVD drive and an analog TV Out 
port, the following paragraph applies:
This product incorporates copyright protection technology that is protected by U.S. patents and 
other intellectual property rights. Use of this copyright protection technology must be authorized 
by Macrovision Corporation, and is intended for home and other limited viewing uses only unless 
otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is 
prohibited.