Gateway 2701hgb Manual

Management and Diagnostic Console
66
The Broadband Link – Detailed DSL Statistics page includes the following information:
Item Description
AT M
Cell Header Errors The number of ATM cell header CRC errors since the 
2Wire gateway was last restar ted, and the elapsed time 
since the last cell header error.
Loss of Cell Delineation The number of ATM loss of cell delineation errors since 
the 2Wire gateway was last restar ted, and the elapsed 
time since the last loss of cell delineation error.
DSL
Link...

Management and Diagnostic Console
67
To reset the DSL statistics, click the Reset button. Cumulative Sec.w/Severe 
ErrorsThe number of severely errored seconds since the 2Wire 
gateway was last restar ted, and the elapsed time since 
the last severely errored second.
Corrected Blocks The number of corrected DSL superframes that had data 
errors detected during reception.
Uncorrectable Blocks The number of uncorrected DSL superframes that had 
data errors detected.
DSL Unavailable Seconds The number of...

Management and Diagnostic Console
68
Broadband Link - Configuration Page
The Broadband Link – Configuration page allows you to modify specific broadband connection settings.
Figure 28. MDC Broadband Link Configuration Page
Note: Modifying the settings on this page can impact the ability of computers on the local 
network to access the broadband connection. You should modify these settings ONLY if you are 
thoroughly familiar with networking. 

Management and Diagnostic Console
69
Modifying DSL and ATM Settings
By default, the gateway automatically detects which DSL line to use. The DSL and ATM Settings pane allows 
you to select a DSL line and manually configure your ATM settings.
To modify DSL or ATM settings:
1.From the DSL Line Selection pull-down, select Automatic, Line 1(inner pair), or Line 2 (outer pair).
2.In the ATM Circuit Identifier VPI and VCI fields, enter the VPI and VCI you want the gateway to use to 
connect to the ISP.
3.From...

Management and Diagnostic Console
70
Modifying Hardware Address
By default, the 2Wire gateway uses its built-in hardware address. The Internet Connection Settings - 
Hardware Address Override pane allows you to manually override the MAC address of the broadband 
connection, which is sometimes required for cable modems that perform MAC address authentication.
To modify the hardware address:
1.Click the Override the built-in hardware address radio button.
2.In the Hardware Address field, enter the...

Management and Diagnostic Console
71
Local Network - Status Page
The Local Network – Status page shows the status of the local network.
Figure 29. MDC Local Network Status Page
The Local Network – Status page includes the following information:
Item Description
IP
Gateway The IP address allocated to the 2Wire gateway.
IP Network The IP address used by the network.
Subnet Mask The subnet mask allocated to the 2Wire gateway.
DHCP Range The range of IP addresses available on the network, the 
number of...

Management and Diagnostic Console
72
DHCP Timeout The time, in minutes, before the DHCP lease must be 
renewed.
Devices
Ethernet The number of Active and Inactive Ethernet devices on 
the network.
Wireless (802.11) The number of Active and Inactive wireless devices on the 
network.
USB Specifies whether a USB device is present (Active) on the 
network. If a USB device is not present, the value is 
Inactive.
Public Network
Router Address Defines a separate network on the home side.
Subnet Mask The subnet...

Management and Diagnostic Console
73
Local Network - Statistics Page
The Local Network – Statistics page shows information about the interfaces on the local network.
Figure 30. MDC Local Network Statistics Page
The Local Network – Statistics page includes the following information:
Item Description
Ethernet
Transmit The cumulative number of frames transmitted over the 
Ethernet home network interface, the number of payload 
bytes transmitted, and the number and percentage of 
transmitted packets in error. 

Management and Diagnostic Console
74
To reset the local network statistics, click the Reset button. Receive The cumulative number of frames received over the 
Ethernet home network interface, the number of payload 
bytes received, and the number and percentage of 
received packets in error.
Wireless (this field is present only on wireless 2Wire gateway models)
Transmit The cumulative number of frames transmitted over the 
wireless home network interface, the number of payload 
bytes transmitted, and the...

Management and Diagnostic Console
75
Local Network - Device List Page
The Local Network - Device List page displays information about each device in the local network.
Figure 31. MDC Local Network Device List Page
The following information is displayed.
Identity. The name of the device. If the device does not have a name associated with it, the device IP 
address is displayed.
Type. The type of connection used by the device to connect to the local network: Ethernet, USB, or 
Wireless.
MAC Address. The...