Gateway 2701hgb Manual

Management and Diagnostic Console
116
The Route List shows a list of static routes defined by the user. For each user-defined static route, the 
following information is displayed: 
 Subnet IP
 Subnet Mask

 Interface  

Management and Diagnostic Console
117
Advanced - DNS Resolve Page
The Advanced - DNS Resolve page allows users to name network devices (such as printers or Web ser vers) 
so that they may be easily accessed by other users on the network.
Figure 50. MDC Advanced DNS Name Table Page
To add entries to the Name table:
1.In the DNS name field, enter a name for the device.
2.In the IP Address field, enter the device’s IP address.
3.Click ADD.
4.The Name table displays the name you defined for each device, the...

Management and Diagnostic Console
118
Advanced - Traffic Shaping Page
The Advanced - Traffic Shaping page allows users to change the 2Wire gateway’s maximum upstream 
connection rate.
Figure 51. MDC Advanced Traffic Shaping Page
To change the gateway’s upstream connection rate:
1.Check the Enable Traffic Shaping checkbox.
2.In the New Upstream Rate field, enter the upstream rate at which you want the gateway to connect.
3.Click the Submit button.
Note: To access this page, your network must have the...

Management and Diagnostic Console
119
Advanced - Link Manager States Page
The Advanced – Link Manager States page is a tree representation of the 2Wire gateway interface stack, 
and shows the internal state of the 2Wire gateway.
Figure 52. MDC Advanced Link Manager States Page
The Link Manager States page is used to gather dynamic information on internal networking modules, and 
is based on the runtime configuration of the 2Wire gateway. The information cannot be used to configure 
the 2Wire gateway. 

Management and Diagnostic Console
120
To view information about each node, click the node link. Information displays below the Link Manager 
States tree, and includes the following:
Node Information Description
Link statusUp. The link is functioning properly.
Climbing. The link is attempting to establish a connection.
Down. The link is not yet configured.
Error. An error has occurred.
State changes The number of times the state of the link has changed (since last 
reboot). 

Management and Diagnostic Console
121
The following table shows the possible nodes that can display on the Link Manager States page.
The nodes that display are dependent on the 2Wire gateway. For example, 2Wire gateways that are not 
connected to the Internet via ADSL will not display ADSL information.Node Description
root0 Root for configuration tree.
global0 Branch for all global configuration modules.
device0 Maintains the status and configuration for devices on the 2Wire gateway.
rnat0 Maintains the...

Management and Diagnostic Console
122
Advanced - Detailed Log Page
The Advanced – Detailed Log page is a debug log facility modeled after syslog, and provides advanced 
diagnostic capabilities.
Figure 53. MDC Advanced Detailed Log Page
Note: The Detailed Log retains a persistent (across upgrades and system restarts) record of 
gateway events. 

Management and Diagnostic Console
123
From the Filter pull-down menus, you can select the level of filtering you want to view (for example, DBG or 
higher) and the specific gateway component that was affected. Each log displays the following information:
 Status level: DBG (debug), INF (informational), NTC (notice), WRN (warning), ERR (error), FTL (fatal), ALR 
(alarm), or EMR (emergency).
 Timestamp (in days, hours, minutes, and seconds) since the state occurred. A “+” preceding the 
timestamp...

Management and Diagnostic Console
124
dhcpd DHCP ser ver
dsl DSL modem and DSL control module
dslice DSL hardware
eth Ethernet device
ethatm Ethernet to ATM bridge (1483)
fw Firewall
gpio GPIO (general purpose input/output) device
hostapd Wireless access point daemon
hpna HPNA interface
httpd HTTP daemon
initd Initd daemon logs for application control
ipsess IP firewall session
jtag JTAG device
kacct Kernel accounting
kelog Kernel event log module
kmem Memor y
kppp PPP kernel network module
kpppoa PPPoA...

Management and Diagnostic Console
125
netdev Network device core
nodesd Network device status daemon
pdump Packet dump (used for debugging)
pkg Package management
pki Public Key Infrastructure subsystem
ppp Point-to-Point Protocol daemon
reset Reset switch driver
rpcd RPCD daemon logs for CMS interaction
rtatm Routed ATM driver
scc Voice SLIC drivers
sip SIP
sntpc Network time client
stream Stream network core
syslog Syslog daemon
system System level
ulib Configuration libraries
usbd USB device
usbhost...