Fujitsu P42hhs30 Users Manual

E-11
English
Description of Input Terminals
DVI-D terminal  (RGB1 INPUT/DVI-D)
Pin No. Input signal Pin No. Input signal
1Red 9 —
2Green 10 Ground
3Blue 11 —
4— 12—
5Ground 13 Horizontal synchronization
6Ground 14 Vertical synchronization
7Ground 15 —
8Ground Frame Ground
RGB2 input terminal (RGB2, 3 INPUT/mD-sub)
2 6 10 14 18
3 7 11 15 194 8 12 16 20
1 5 9 13 17 21
SCART terminal (Video1, 2, 4)Pin No.Input Signal
1—
2Right audio
3—
4Audio ground
5Blue ground
6Left audio
7Blue
Pin No.Input Signal
8—...

E-12
PART NAMES AND FUNCTIONS (Continued)
REMOTE CONTROL
For details, see page .
1 button 
Switches between power ON and standby
state.
4DISPLAY OFF button 
For showing on-screen-information.
5PICTURE MODE button 
Switches the picture mode.
8AUDIO IN button 
Selects the input audio.
0Video input mode selector button
[VIDEO 1 – 6] 
Selects VIDEO 1 – 6.
ARGB input mode selector button
[RGB 1 – 3] 
Selects RGB 1 – 3.
CMenu button [MENU] 
 – 
Use this button to display a desired menu
for adjusting the...

E-13
English
PUTTING BATTERIES IN THE REMOTE CONTROL
1To remove the cover, slide it
outwards while pressing it down.2Place two AA batteries in the
remote control.  Make sure that the
batteries are properly oriented.3Close the cover until it snaps into
place.
Note
The remote control will not function properly if the batteries are dead.  Be sure to replace them as needed.
Do not use rechargeable batteries (Ni-Cd).
CAUTION:Be sure to use replacement batteries of the same type as the original ones.
When...

E-14
EFFECTIVE RANGE FOR THE REMOTE CONTROL
Point the remote control at the display’s signal receiver when using it.
Make sure that there are no obstacles between the remote control and the display’s signal receiver.
USING THE REMOTE CONTROL (Continued)
Information
The remote control may not function properly if you use a high-frequency fluorescent lamp.  If you experience problems, move the lamp or use the
remote control from a different position.
Selector – side
Display – front
Selector – front
Right...

E-15
English
Be sure to turn OFF the power to the display and external equipment before making any connections.
No cables are supplied with the display for connection to external equipment.  The type of cable to be used varies depending on the PC
model.  Contact your dealer for more information.
RECEPTACLE
Make sure that the power cable’s grounding wire is grounded.
The display comes with a 3-prong power plug; one prong is connected to the grounding wire.  If you have only a 2-hole receptacle, you
will...

E-16
BASIC SYSTEM CONNECTIONS
CONNECTING THE DISPLAY TO EXTERNAL EQUIPMENT (Continued)
1. Connect the following items to the selector and the display
1Selector and display
Connect these two with the provided system connection cable. (For details, see the page on the right.)
2Speakers
For how to connect speakers, see the instructions provided with the speakers.
2. Connecting the power cord
•Connect the power plug of the display and selector power cords to a grounded 3-pin outlet.
SelectorOutlet
Outlet...

English
E-17
AUDIO
INPUTVIDEO5 VIDEO6 RGB1 RGB2
DIGITAL1 DIGITAL2
VIDEO1
PICTUREINPUT
DIGITALAUDIO
OUTPUT
DISPLAY OUTPUT
VIDEO2
VIDEO4
mD-sub
PICTURE AUDIO VIDEO5VIDEO1
Y            P
B/CB         PR/CRCOMPONENT VIDEOY            PB/CB         PR/CRCOMPONENT VIDEORGB2
RGB1
DVI SCARTSCART SCART
&9541
	™

3-%*41-:
*/165
6%*0
%*41-:
*/165

1*$53&
CONNECTING THE DISPLAY AND THE SELECTOR
Rear side of display
Left speaker cable Right speaker cable
Red
Black
Power input
Audio
terminalPicture
terminal
To...

E-18
CONNECTING THE DISPLAY TO EXTERNAL EQUIPMENT (Continued)
EXAMPLE OF CONNECTION TO EXTERNAL COMPONENTS
Remote
control DisplaySpeaker (optional)
Speaker
VCR or other external components See P. 
Selector
VCR 
DVD player 
Amplifier 
Satellite tuner 
Video camera 
Videogame machine 
PC 

&.)%	@
KQ03.10.30, 19:36 Page 18EPCF
1BHF.BLFS
+11$
 

English
E-19
VCR
•Connect the video signal cable to the SCART terminal.
AUDIO
INPUTVIDEO5 VIDEO6 RGB1 RGB2
DIGITAL1 DIGITAL2
VIDEO1
PICTUREINPUT
DIGITALAUDIO
OUTPUT
DISPLAY OUTPUT
VIDEO2
VIDEO4
mD-sub
PICTURE AUDIO VIDEO5VIDEO1
Y            P
B/CB         PR/CRCOMPONENT VIDEOY            PB/CB         PR/CRCOMPONENT VIDEORGB2
RGB1
DVI SCARTSCART SCART
To SCART output
To SCART input
Rear side of selector
Note
•Unplug the power cord from the AC outlet before you connect external components.
•Also refer to...

E-20
CONNECTING THE DISPLAY TO EXTERNAL EQUIPMENT (Continued)
AMPLIFIER
•Connect the audio signal cable to either the digital output or the analog audio output.
*The signal input as digital input is not output as analog audio.
*The digital audio input terminal on the display complies with a sampling frequency of 48 kHz.
In the case of outputs with another frequency, connect to an audio system (amplifier)*.
AUDIO
INPUTVIDEO5 VIDEO6 RGB1 RGB2
DIGITAL1 DIGITAL2
VIDEO1
PICTUREINPUT
DIGITALAUDIO
OUTPUT...