Faroudja Fdp-Dila1 Installation And Operations Manual

Home Theater Optimized
FDP-DILA1
Installation and 
Operations Manual
NOTICE: THIS PROJECTOR HAS BEEN SIGNIFICANTLY
MODIFIED AND OPTIMIZED TO PRODUCE VERY HIGH
QUALITY IMAGES USING THE FAROUDJA PROCESSOR.
ANY CHANGES MADE TO THESE SETTINGS CAN CORRUPT
THIS PROCESS. RESETTING THE OPTIMIZATION IS NOT
COVERED UNDER WARRANTY.
™ 

2
Thank you for purchasing this projector. Before using it, read and follow all instructions carefully to take full
advantage of the projectors capabilities.
SAFETY PRECAUTIONS
WARNING :
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION :
To reduce the risk of electric shock, do not remove cover.
Refer servicing to qualified service personnel.
FCC INFORMATION (U.S.A. only)
CAUTION: Changes or modification not approved by
JVC could void the users authority to...

3
ENGLISH
Ð This product should be operated only with the type ofpower source indicated on the label.  If you are not sure
of the type of power supply to your home, consult your
product dealer or local power company.
Ð This product is equipped with a three-wire plug.  This plug will fit only into a grounded power outlet.  If you are
unable to insert the plug into the outlet, contact your
electrician to install the proper outlet.  Do not defeat the
safety purpose of the grounded plug.
Ð Power-supply cords...

4
Contents
SAFETY PRECAUTIONS ........................... 2
Accessories ............................................... 5
Controls and Features .............................. 6
Front Side / Top Surface / Right Side .................... 6
Left-hand side ....................................................... 7
Bottom Surface ..................................................... 8
Control Panel ........................................................ 9
Connector Panel...

5
ENGLISH
Remote control unit (RM-M10G) AAA/R03-size dry cell battery (´2)
(for checking operation) Power code
[approx. 2.5 m (8.2 ft)]
Personal computer connection cable [approx. 2 m (6.56 ft)](D-sub, 3-row 15 pin)
Conversion adapter for Mac (for Macintosh) Audio cable
[approx. 3 m (9.84 ft)]
(3.5 mm dia. stereo mini plug)
AV connection cable
[approx. 1.5 m (4.92 ft)]
BNC-RCA conversion plug
Accessories
The following accessories are included with this projector. Check for them; if any item is missing,...

6
Controls and Features
Front Side / Top Surface / Right Side
STAND BY
OPERATE
LAMP
TEMP
EMERGENCY
VIDEO
COMPUTER
SETTING
QUICK
ALIGN
-2+3
91
8
7
6
52
3 4
1Control panel
For details, refer to ÒControl PanelÓ (page 9).
2Exhaust vents
Vents for cooling fans through which warm air comes out.
CAUTION
¥ Do not block the exhaust vents, or heat builds up inside,
possibly causing a fire. Also, do not touch the vents, or this
could cause a low-temperature burn.
3Carrying handle
Raise this handle when carrying the...

7
ENGLISH
Controls and Features (cont.)
Left-hand side
p
q
w
e
pAC IN (power input) terminal
This is the power input terminal where the supplied power
cord is connected. For details, refer to page 24.
qMAIN POWER switch
This is the main power switch. When it is turned on, the
projector goes into stand-by state, and the STAND BY
indicator on the control panel comes on.
ON [  y ]: The main power turns on.
OFF [ à
à à
à
à ]: The main power turns off.
wConnector panel
For details, refer to ÒConnector PanelÓ...

8
Controls and Features (cont.)
Bottom Surface
rAir intake area (filter)
Air is taken in through this area to cool the light-source
lamp. If this area is blocked or if something that obstructs
taking in or exhausting air is placed around the projector,
heat may build up inside and could cause a fire. For details,
refer to ÒPrecautions for InstallationÓ on page 15.
CAUTIONS
¥ Be careful as paper, cloth or soft cushion could be drawn in
if placed nearby. Do not block the intake area, or heat may
build up...

9
ENGLISH
Controls and Features (cont.)
Control Panel
1STAND BY Indicator
ON :When in stand-by mode.
Blinking : When in cool-down mode.
Memo
About the cool-down mode:
This projector has a function to cool down the heated lamp for a fixed
period  of time after projection is finished. This feature is referred to as
the cool-down mode.
CAUTION
¥ The purpose of the cool-down mode is to prevent inner parts from being deformed or broken by heat from the heated lamp
as well as to prolong the life of the lamp....

10
Controls and Features (cont.)
Control Panel (Cont.)
7VIDEO button
Use this button to select a device such as a video deck
connected to the AV IN terminal of the projector. Each time
you press the button, the device selected changes as
follows:
Y/C
VIDEOY, PB/B-Y,PR/R-Y
8COMPUTER button
Use this button to select a device connected to the
COMPUTER -1 or -2 terminals. Each time you press the
button, the selection changes as follows:
COMPUTER 1
COMPUTER 2
9SETTING button
Use this button to call up the...