Epson WorkForce 320 User Manual

							Installing for the First Time31 2. When you see this screen, connect the product to your computer with a USB 
cable.
3. Follow the on-screen instructions to continue installing the software.
4. When you see the Firewall Warning screen, click 
Next.
Note: 
If you see a firewall alert message, click Unblock or Allow to let EpsonNet Setup 
continue. Do not select Ask Me Later, Keep Blocking, or Block.
 
						

							32Installing for the First Time
5. When you see a screen like the following, select your network name (SSID) 
from the list, then click 
Next.
Note: 
If your network name isn’t in the list, select Enter Manually. If your network name 
contains uppercase (ABC) or lowercase (abc) letters, enter them correctly.
6. If you see a screen like the following, enter your security key or passphrase, 
then click 
Next.
Note: 
If your security key contains uppercase (ABC) or lowercase (abc) letters, enter 
them correctly.
 
						

							Installing for the First Time33 7. Wait while EpsonNet Setup configures your product for the network.
8. Follow the instructions on the screen to remove the USB cable from the 
product and your computer.
9. When you see the Installation Complete screen, print a test page, then click 
Finish.
10. Follow the on-screen instructions to install the rest of your software.
When installation is complete, remove the CD and restart your computer. 
To set up additional computers to print to the product, see “Setting Up Additional 
Computers” on page 37.
Setting Up With the Product Buttons
If you are using Mac OS X 10.6, or you did not connect a USB cable to set up the 
product on your wireless network, follow these steps to set it up using the product 
buttons:
1. Follow the instructions on the screen to start the product’s wireless Setup 
Wizard.
 
						

							34Installing for the First Time
2. When you see this screen, use the product’s buttons to select the name of your 
wireless network, then press 
OK. When you’re finished, click Next.
If your network name isn’t listed, try the following:
■Make sure that your wireless router or access point is turned on and 
working correctly. Press the 
yStop/Clear Settings button to return to 
the previous screen, press 
OK to select Setup Wizard, then repeat step 2.
■If you still can’t find the network name in the list, your router or access 
point is not broadcasting its network name. Press uor  d to select 
Other 
SSIDs
, then press OK. Continue with the steps in “Entering Your SSID 
Manually” on page 36.
3. When you see this screen, do one of the following:
■If your wireless network has security enabled, use the product’s buttons to 
enter your network password. If your password has uppercase or lowercase 
letters, be sure to enter them correctly. Then click 
Next and go to step 4.
 
						

							Installing for the First Time35
■If your wireless network doesn’t have security enabled, click Next and 
continue with step 4.
Note: 
If you’re having trouble entering your network password, click Watch video 
overview to watch a short video tutorial on how to enter your network password. 
4. Follow the on-screen instructions to finish selecting network settings.
If you see a network setup failed message, the network password may have 
been entered incorrectly. If your password has uppercase or lowercase letters, 
or numbers, be sure to enter them correctly.
Note: 
If the product still doesn’t connect to your wireless network, see “The product 
cannot find or connect to the wireless router or access point” on page 42.
5.Mac OS X 10.6: Skip to step 10 on page 36.
6. Wait while the software is installed.
7. When you see the Firewall Warning screen, click 
Next.
Note: 
If you see a firewall alert message, click Unblock or Allow to let EpsonNet Setup 
continue. Do not select Ask Me Later, Keep Blocking, or Block.
8. Wait while EpsonNet Setup configures your product for the network.
 
						

							36Installing for the First Time
9. When you see the Installation Complete screen, print a test page, then click 
Finish.
10. Follow the instructions on the screen to install the rest of your software.
When installation is complete, remove the CD.
To set up additional computers to print to the product, see “Setting Up Additional 
Computers” below.
Entering Your SSID Manually
If your network doesn’t broadcast its name (SSID), follow these steps to enter it:
1. From the Select SSID screen on the product control 
panel, press uor  d to select 
Other SSIDs, then 
press 
OK.
2. Use the numeric keypad on the control panel to enter your 
network name. 
Important: 
Network names are case-sensitive. Be sure to enter uppercase 
letters (ABC) or lowercase letters (abc) correctly.
■
Press the buttons repeatedly to select uppercase letters or 
lowercase letters, or numbers and special characters.
■Press r to move to the next character.
■Press l to delete a character.
 
						

							Setting Up Additional Computers37 3. When you’re done entering your network name, 
press 
OK.
4. Continue with step 3 on page 34 to enter your 
network password.
Setting Up Additional Computers
1. Make sure your product is turned on.
2. Insert the product software CD.
3.Windows 7 and Windows Vista: If you see the AutoPlay window, click 
Run 
Setup.exe
. When you see the User Account Control screen, click Yes or 
Continue.
Windows XP: When you see the Software Installation screen, continue with 
step 4.
Mac OS X: Double-click the 
Epson icon.
4. When you see this screen, click 
Install.
 
						

							38Setting Up Additional Computers
5. When you see this screen, select Wireless connection and click Next.
6. When you see this screen, select 
The printer is already on my wireless 
network
, then click Next.
7. Wait while the software is installed.
8.Mac OS X 10.6: Skip to step 13 on page 40.
 
						

							Setting Up Additional Computers39 9. When you see the Firewall Warning screen, click 
Next.
Note: 
If you see a firewall alert message, click Unblock or Allow to let EpsonNet Setup 
continue. Do not select Ask Me Later, Keep Blocking, or Block.
10. If you see a screen like this one, select the product you would like to set up, 
then click 
Next.
11. Wait while EpsonNet Setup configures your product for the network.
 
						

							40Setting Up Additional Computers
12. When you see the Installation Complete screen, print a test page, then click 
Finish.
13. Follow the instructions on the screen to install the rest of your software.
When installation is complete, remove the CD.