Epson Stylus Pro 9400 User Manual

Paper Handling271
6
6
6
6
6
6
6
6
6
6
6
6
English
Using Cut Sheet Media
Loading cut sheet media
To load cut sheet media longer than 483 mm (long edge of Super 
A3/B), see the next section. To load paper with a length of A4, 
Letter, A3, US B, and Super A3/B, see “Loading cut sheet with a 
length of A4/Letter, A3/US B, and Super A3/B” on page 274.
If you are printing on thick paper (0.5 to 1.5 mm), see “Printing 
on thick paper (0.5 to 1.5 mm)” on page 275.
Loading cut sheet media longer than 483 mm (long...

272Paper Handling 3. Make sure that the Power light is not flashing, and then set 
the paper lever to the released position. The LEVER RELEASED. 
LOAD PAPERappears on the LCD panel.
c
Caution:
Do not set the paper lever to the released position while the 
Power light is flashing; otherwise, damage may occur.
4. Load the sheet into the paper insertion slot until it comes out 
below. Make sure that the right and bottom edges of the sheet 
are straight and in line with the horizontal line and the vertical...

Paper Handling273
6
6
6
6
6
6
6
6
6
6
6
6
English
5. Set the paper lever to the secured position. PRESS PAUSE 
BUTTON appears on the LCD panel.
6. Press the Pause  button.
The print heads move and the sheet feeds into the printing 
position automatically. READY appears on the LCD panel.
Note:
Even if you do not press the Pause  button, the print heads move 
and paper feeds into the printing position automatically. READY 
appears on the LCD panel.
Now the printer is ready to print. While the printer is...

274Paper Handling
Loading cut sheet with a length of A4/Letter, A3/US B, and 
Super A3/B
To load cut sheet media with a length of A4/Letter, A3/US B, and 
Super A3/B, follow the steps below.
c
Caution:
As much as possible, keep your fingers off the printable surface of 
the media, as fingerprints may reduce printout quality.
1. Make sure that the printer is on and the roll paper cover is 
closed.
2. Press the Paper Source l button repeatedly until Sheet
  
appears.
3. Make sure that the paper lever is in...

Paper Handling275
6
6
6
6
6
6
6
6
6
6
6
6
English
Note:
Even if you do not press the Pause  button, the print heads move 
and paper feeds into the printing position automatically. READY 
appears on the LCD panel.
Now the printer is ready to print. While the printer is printing, do 
not open the front cover. If the front cover is opened while 
printing is in progress, the printer stops printing, and then restarts 
printing when the front cover is closed. Stopping and restarting 
printing may reduce the...

276Paper Handling 2. Make sure that the printer is on.
3. Press the Paper Source l button repeatedly until Sheet
  
appears.
4. Make sure that the Power light is not flashing, and then set 
the paper lever to the released position. LEVER RELEASED. 
LOAD PAPERappears on the LCD panel. 
5. Open the front cover.
 

Paper Handling277
6
6
6
6
6
6
6
6
6
6
6
6
English
6. Load the sheet into the paper insertion slot so that the bottom 
edge of the paper rests behind the open front cover. Make sure 
that the right and bottom edges of the sheet are straight and 
in line with the horizontal line and the vertical line.
7. Set the paper lever to the secured position, and then close the 
front cover. PRESS PAUSE BUTTON appears on the LCD panel.
8. Press the Pause 
 button, and then follow the same 
procedure used for other...

278Paper HandlingNote:
Even if you do not press the Pause  button, the print heads move 
and paper feeds into the printing position automatically. READY 
appears on the LCD panel.
c
Caution:
Do not leave the paper in the printer for a long period of time; its 
quality will deteriorate. We recommend that you remove the paper 
from the printer after printing.
Setting the Paper Basket 
To avoid your printouts getting dirty or crinkled, set the paper 
basket as explained below. You can use the paper basket...

Paper Handling279
6
6
6
6
6
6
6
6
6
6
6
6
English
1. Make sure that the upper hooks are fully inserted, and the 
paper guides are in front of the paper basket. 
2. Put the lower shafts down in the forward position as shown, 
so that they rest on the floor.
 

280Paper Handling
When feeding paper backward
Note:
❏When feeding roll paper larger than the B0 size backward, make sure 
that your printer has at least 30 cm (12 inches) of space to its rear. 
This prevents the printed paper edges from folding.
❏When you feed paper backward, remove the flange from the drive 
unit and fully slide the movable unit to the left side of the printer; 
otherwise, the printed paper may conflict with the Auto Take-up 
Reel Unit and paper feed error may occur.
1. Take off the...