Epson Stylus Pro 9400 User Manual

The Control Panel231
4
4
4
4
4
4
4
4
4
4
4
4
English
If you are not satisfied with the result of this alignment, press 
the Paper Source l button to return to the previous level, 
and then select BI-D ALL. 
If you are not satisfied with the result of the BI-D ALL 
alignment, try UNI-D. 
12. After you set the patterns, press the Pause 
 button to return 
to the READY state.
Making the paper settings
You can register and recall your own paper settings for any media.
The paper settings you can make are:...

232The Control Panel 1. Load the paper that you want to check.
2. Press the Menu r
 button to enter the Menu mode.
3. Press the Paper Feed d button or Paper Feed u button to 
display CUSTOM PAPER.
4. Press the Menu r button to display PAPER NUMBER.
5. Press the Menu r button, and then press the Paper Feed d 
button or Paper Feed u button to select STANDARD or the 
number (No. 1 to No. 10) you want to register as the setting. 
If you use Epson special media, select STANDARD and then go 
to step 11. You do...

The Control Panel233
4
4
4
4
4
4
4
4
4
4
4
4
English
11. Examine the printed pattern to determine which set of lines 
are aligned (showing the smallest gap), and note the 
corresponding number.
12. After the pattern is printed, THICKNESS NUMBER appears. Press 
the Paper Feed d button or Paper Feed u button to select 
the number noted in step 11, and then press the Enter 
 
button to save the selected value.
13. Press the Paper Source l button.
14. Select CUT METHOD, and then press the Menu r button....

234The Control Panel 22. Select M/W ADJUSTMENT, and then press the Menu r button. 
Press the Paper Feed d button or Paper Feed u button to 
adjust MicroWeave. Increase the value to give priority to the 
print speed, or decrease it to give priority to the print quality. 
Press the Enter 
 button to save the selected value.
Selecting the registered settings
To select the registered settings, follow the steps below.
1. Press the Menu r
 button to enter the Menu mode.
2. Press the Paper Feed d button or...

The Control Panel235
4
4
4
4
4
4
4
4
4
4
4
4
English
3. Press the Paper Feed d button or Paper Feed u button to 
display TEST PRINT, and then press the Menu r
 button.
4. Press the Paper Feed d button or Paper Feed u button to 
display STATUS SHEET, and then press the Menu r button.
5. Press the Enter 
 button again to start printing a status sheet.
After printing is finished, follow the message on the LCD to 
return to the READY state.
Setting the alert value of the paper
You can get a message when...

236The Control Panel 6. Press the Enter 
 button to set the alert value.
7. After you set the alert value, press the Pause 
 button to 
return to the READY state.
 

Maintenance Mode237
5
5
5
5
5
5
5
5
5
5
5
5
English
Chapter 5
Maintenance Mode
Maintenance Mode
Maintenance mode setting procedure
This section describes how to enter the maintenance mode and 
make settings with the buttons on the control panel.
To make the maintenance mode settings, follow the steps below.
Note:
❏Press the Paper Source l button to return to the previous step.
❏While you are using the printer in the Maintenance mode, no error 
message (if any) appears on the LCD. Therefore, use the...

238Maintenance Mode 4.Select a parameter.
Press the Paper Feed d button or Paper Feed u button to 
select a parameter for the item. 
5.Set the parameter.
Press the Enter 
 button to store the selected parameter. 
If the parameter is used for execution only, press the Enter 
 
button to execute the function for the item. 
Note:
If a second parameter is displayed on the LCD, repeat steps 4 and 5 
to select and set the second parameter.
6.Exit the maintenance mode.
Press the Power 
 button to turn off the...

Maintenance Mode239
5
5
5
5
5
5
5
5
5
5
5
5
English
Maintenance mode list
Item First parameters Second parameters
“HEX DUMP” on 
page 240PRINT EXECUTE
“LANGUAGE” on 
page 241ENGLISH, FRENCH, 
ITALIAN, GERMAN, 
PORTUGUE, SPANISH, 
DUTCH-
“REMAINING PPR 
SETUP” on page 241OFF, ROLL -
“UNIT” on page 242 METER, FEET/INCH -
“CUT PRESSURE” on 
page 2420% - 150% -
“SS CLEANING” on 
page 242EXECUTE -
“PWR ON ROLL PPR 
FEED” on page 242ON, OFF -
“SHEET AUTO FEED 
TIME” on page 2425sec, 3sec, OFF 
(MANUAL FEED)-...

240Maintenance Mode
Details of maintenance mode items
HEX DUMP
Data received from the host computer can be printed out in 
hexadecimal numbers.
To print out the data, follow the steps below.
1. Make sure that paper is loaded in the printer. 
2. While in the maintenance mode, press the Paper Feed d 
button or Paper Feed u button to display HEX DUMP.
3. Press the Menu r button to display PRINT, and then press the 
Enter 
 button again to start printing. 
“INK INFO MENU” on 
page 243EPSON Stylus Pro...