Epson Stylus Pro 11880 User Manual

11
Introduction|11
Before you call, make sure you have your Unit ID number, which is 
included with the Epson Preferred Limited Warranty Plan information that 
came with your printer. You’ll also need your printer serial number. 
Visit Epson’s U.S. support website or Canadian support website for 
solutions to common problems. You can download drivers, firmware, and 
documentation, get FAQs and troubleshooting advice, or e-mail Epson with 
your questions.
Macintosh System Requirements
To use your printer...

12
12|Introduction
Windows System Requirements
To use your printer in either a stand-alone or network environment, your 
system should include the requirements listed below:
IBM®-compatible PC with a Pentium® 4, 3 GHz or higher processor 
recommended 
Microsoft® Windows® XP, Windows XP Professional x64 Edition, 
Windows Vista,™ or Windows Vista x64
At least 1GB of RAM (2GB or more recommended)
At least 30GB of free hard disk space for software and processing files 
Quad-speed (4×) CD-ROM or DVD drive for...

13
Introduction|13

Keep the printer away from dusty areas.
Keep your entire computer system away from potential sources of 
electromagnetic interference, such as loudspeakers or the base units of 
cordless telephones.
Place the printer near a wall outlet where the plug can be easily 
unplugged.
Use only the type of power source indicated on the label. 
Connect the printer to a properly grounded outlet. Avoid using an 
outlet on the same circuit as a photocopier or air control system that 
regularly...

14
14|Introduction

Power down the printer from the control panel, unplug the printer, and 
refer servicing to qualified service personnel under the following 
conditions: 
The power cord or plug is damaged; liquid has entered the printer; the 
printer has been dropped or the cabinet damaged; the printer does not 
operate normally or exhibits a distinct change in performance.
The interface connectors and the connector for the Auto Take-up Reel 
are limited power source connectors.
Do not touch the front...

15
Introduction|15
Ink Cartridge Safety Instructions
Keep ink cartridges out of the reach of children and do not drink the 
ink.
Store ink cartridges in a cool, dark place.
If ink gets on your skin, wash it off with soap and water. If ink gets in 
your eyes, flush them immediately with water.
Shake ink cartridges well before installing them for best results. 
Do not use an ink cartridge beyond the date printed on the cartridge 
carton.
Use up the ink cartridge within six months of installation for best...

16
16|Introduction
Printer Parts
Front
Back
Roll paper 
spindle
Left ink 
bay Roll paper 
holder
Front cover
Paper guide
Auto take-up reelRight 
ink bay Ink cover button Roll paper 
cover
Paper lever
Ink bay lights
Locking 
caster
Locking casterTake-up 
reel 
sensor
Control panel
USB 
connector
Network 
connector Auto take-up 
reel connector
AC 
inletLeft 
maintenance 
tank
Center 
maintenance 
tank Right 
maintenance 
tank
Take-up reel 
reflector
 

17
Introduction|17
Control Panel
LCD Display
LCD display
Power 
buttonPause or reset 
button and light
Ink light
Paper source or cut button Paper lightMenu or 
cleaning button
Paper feed up button
Paper feed down button Enter or barcode 
button
Take-up reel 
Backward 
button
Power 
light
Take-up reel 
Forward button
Status or error 
message
Roll paper 
margin setting
Custom paper 
number selected
Paper source
Platen gap 
settingInk gaugesLength of roll 
paper remaining
Maintenance 
tank gauges
 

18
18|Introduction
 

19
19
This chapter includes the following information:
Unpacking and assembling the printer
Connecting the power cord
Installing ink
Connecting to the network
Updating the printer firmware
Configuring the printer for your network
Unpacking and Assembling the Printer
Follow these steps to assemble your printer and its stand. Before you begin, 
select an appropriate location to set up and use the printer. 
Choose a flat and stable location that can support the printer’s weight 
(about 331 lb, without the...

1-20
20|Setting Up the Printer
Unpacking and Assembling the Stand
1. Open the printer box and remove the box that contains the stand.
2. Unpack the stand and make sure you have all these items:
WARNING: Two people 
are required to unpack 
the printer, and four are 
needed to place it on the 
stand.
Support bar
Hex wrench4 Bolts
4 Wing nuts with spring 
washers and plain washers
Base sections