Epson Projector PT EZ590 User Manual

							Chapter 7 Appendix — Technical information
ENGLISH - 151
 terminal
The  terminal of the projector conforms with RS-232C so that the projector can be connected to and 
controlled from a computer.
Connection
When connecting directly
When connecting with DIGITAL LINK compatible devices
D-Sub 9p (female)
D-Sub 9p (male) Computer
Communication cable (straight)
LAN cable (straight) D-Sub 9p (male)
Communication cable (straight)Computer
(Only for PT-EZ590, PT-EW650 and PT-EX620)
Projector connecting terminals
D-Sub 9p (female)
DIGITAL LINK
DIGITAL LINK DIGITAL LINK compatible device
Projector connecting terminals
Note
 
f The destination of [RS-232C] (
x page 95) must be set according to the connection method.
 
f When connecting by a DIGITAL LINK compatible device, set the [PROJECTOR SETUP] menu 
→ [ECO MANAGEMENT] 
→ [STANDBY 
MODE] ( x page 94) to [NORMAL] to control the projector in standby mode.
When [STANDBY MODE] is set to [ECO], the projector cannot be controlled during standby.
Pin assignments and signal names
D-Sub 9-pin (female) Outside view Pin No.
Signal name Details
(9)
(6)
(5)
(1)
(1) ―NC
(2) TXDTransmitted data
(3) RXDReceived data
(4) ―NC
(5) GNDEarth
(6) ―NC
(7) CTS
Connected internally
(8) RTS
(9) ―NC
Communication conditions (Factory default)
Signal level RS-232C-compliant
Sync. method Asynchronous
Baud rate 9 600 bps
Parity None
Character length 8 bits
Stop bit 1 bit
X parameter None
S parameter None       
						

							Chapter 7 Appendix — Technical information
152 - ENGLISH
Basic format
Transmission from the computer starts with STX, then the ID, command, parameter, and ETX are sent in this 
order. Add parameters according to the details of control.
(2 bytes)
2 ID characters (2 bytes)Semi-colon (1 byte) Colon (1 byte)
3 command characters (3 bytes) Parameter (undefined length)
Start (1 byte) ZZ, 01 to 64
ID designate
End (1 byte)
Basic format (has subcommands)
Parameter (6 bytes)*1
Symbol “+” or “-” (1 byte) and setting or adjustment value\
 (5 
bytes)
Operation (1 byte)
*1
“=” (Set the value specified using parameter)
Sub command (5 bytes) Same as the basic format
*1 
When transmitting a command which does not need a parameter, an operation (E) and parameter are not necessary.
Attention
 
f If a command is transmitted after the lamp starts illuminating, there may be a delay in response or the command may not be executed. 
Try 
sending or receiving any command after 60 seconds.
 
f When transmitting multiple commands, be sure to wait until 0.5 seconds has elapsed after receiving the response from the projector before 
sending the next command. When transmitting a command which does not need a parameter
, a colon (:) is not necessary.
Note
 
f If a command cannot be executed, the “ER401” response is sent from the projector to the computer
.
 
f If an invalid parameter is sent, the “ER402” response is sent from the projector to the computer
.
 
f ID transmission in RS-232C supports ZZ (ALL) and 01 to 64.
 
f If a command is sent with a specified ID, a response will be sent to the computer only in the following cases.
 
g It matches the projector ID
 
g When [PROJECTOR ID] (
x page 92) on the projector is [ALL]
 
f STX and ETX are character codes. STX shown in hexadecimal is 02, and ETX shown in hexadecimal is 03.   
						

							Chapter 7 Appendix — Technical information
ENGLISH - 153
Cable specification
1
NC    NC 1
2 2
3 3
4 NC    NC 4
5 5
6 NC    NC 6
7 7
8 8
9 NC    NC 9
When connected to a computer
Projector
( terminal) Computer
(DTE specifications)
Control command
The following table lists the commands that can be used to control the p\
rojector using a computer.
 
r Projector control command
Command DetailsParameter/response 
string Remark (parameter)
PON Power on
―To check if the power is on, use the “Power query” command.
POF Power standby
QPW Power query 000
001STANDBY
Power on
IIS Switching the input 
signal VID
VIDEO
RG1 RGB1
RG2 RGB2
HD1 HDMI1
HD2 HDMI2
DL1 DIGITAL LINK 
*1
NWP NETWORK
Q$L Lamp cumulative 
runtime query 1
Returned with 0 to 99999
OSH Shutter control
 *1/AV 
mute control *20 Shutter function off (shutter open)/AV mute function off
QSH Shutter status query 
*1 /
AV mute status query *21 Shutter function on (shutter closed)/AV mute function on
Q$S Lamp condition query 0
1
2
3Stand-by
Lamp ON control active
Lamp ON
Lamp OFF control active
VSE Aspect ratio switch 0
AUTO
1 NORMAL
2 WIDE
5 NATIVE
QS1 Aspect ratio settings 
query 6
FULL
9 H FIT
10 V FIT
*1 Only for PT-EZ590, PT-EW650 and PT-EX620
*2  Only for PT-EW550 and PT-EX520
 
r Projector control command (with sub command)
Command Sub command Details Remark
VXX RYCI1RGB1 input setting +00000=RGB/YP
BPR, +00001=Y/C   
						

							Chapter 7 Appendix — Technical information
154 - ENGLISH
 
r Lens control command
Command Sub command Details Remark
VXX LNSI2Lens H shift
+00000=Fine adjustment 1+, +00001=Fine adjustment 1
-, 
+00100=Fine adjustment 2+, +00101=Fine adjustment 2-, 
+00200=Coarse adjustment+, +00201=Coarse adjustment-
VXX LNSI3Lens V shift
VXX LNSI4Lens focus
VXX LNSI5Lens zoom
 terminal
It is possible to control the projector remotely (by external contact) from a control panel located away from the 
projector where remote control signals cannot reach.
Use the  terminal on the connecting terminals of the projector to connect to the control panel.
Installation locations in meeting rooms, etc. Remote control board in another locationRemote control
Contact control
Standby Lit
Lamp
RGB1
RGB2 VIDEO HDMI1
HDMI2
Remote control/Contact control
Pin assignments and signal names
D-Sub 9-pin
Outside view Pin No.
Signal name Open (H)Short (L)
(9)(6)
(5)
(1)
(1) GND ―GND
(2) POWER OFFON
(3) RGB1 OtherRGB1
(4) RGB2 OtherRGB2
(5) VIDEO OtherVIDEO
(6) HDMI1 OtherHDMI1
(7) HDMI2 OtherHDMI2
(8) SHUTTER 
*1OFF ON
(9) RST/SETControlled by remote 
control Controlled by external 
contact
*1  For PT-EZ590, PT-EW650 and PT-EX620 
[AV MUTE] for PT-EW550 and PT-EX520
Attention
 
f When controlling, make sure to short-circuit pins (1) and (9).
 
f When pins (1) and (9) are short-circuited, the following buttons on the control panel and the remote control are disabled. Commands for 
RS-232C and network functions corresponding to these functions are also disabled.
 
g Power <
v/
b > button,  button,  button,  button,  button,  button,  
button,  button and  button 
Note
 
f For pin (2) to pin (8) settings, you can make changes if you set [REMOTE1 MODE] to [USER]. (
x page 96)       
						

							Chapter 7 Appendix — Technical information
ENGLISH - 155
[MENU LOCK PASSWORD] operations
To initialize your password, consult your distributor.   
						

							Chapter 7 Appendix — Technical information
156 - ENGLISH
List of compatible signals
The following table specifies the video signals compatible with the projector
.
 
f Symbols that indicate formats are as follows.
 
g V: VIDEO, Y/C
 
g R: RGB
 
g Y: YC
BCR/YPBPR
 
g H: HDMI/DIGITAL LINK
Mode Display resolution
(dots) Scanning frequency
Dot clock 
frequency 
(MHz) Format Plug and play*
1
Horizontal 
(kHz) Vertical 
(Hz) RGB2HDMI/
DIGITAL  LINK
NTSC/NTSC4.43/ PAL-M/PAL60 720 x 480i
15.759.9 ―V
― ―
PAL/PAL-N/SECAM 720 x 576i15.650.0 ―V― ―
525 (480) /60i 712 x 483i15.759.913.5 R/Y― ―
625 (576) /50i 702 x 575i15.650.013.5 R/Y― ―
525 (480) /60i 720 (1 440) x 480i*215.759.927.0 H――
625 (576) /50i 720 (1 440) x 576i*215.650.027.0 H――
525 (480) /60p 720 x 48031.559.927.0R/Y/H―
l
625 (576) /50p 720 x 57631.350.027.0R/Y/H―
l
750 (720) /60p 1 280 x 72045.060.074.3R/Y/H―
l
750 (720) /50p 1 280 x 72037.550.074.3R/Y/H―
l
1125 (1080) /60i*31 920 x 1 080i33.860.074.3R/Y/H―
l
1125 (1080) /50i1 920 x 1 080i28.150.074.3R/Y/H―
l
1125 (1080) /24p1 920 x 1 08027.024.074.3R/Y/H―
l
1125 (1080) /24sF1 920 x 1 080i27.048.074.3R/Y/H― ―
1125 (1080) /25p1 920 x 1 08028.125.074.3R/Y/H― ―
1125 (1080) /30p1 920 x 1 08033.830.074.3R/Y/H― ―
1125 (1080) /60p1 920 x 1 08067.560.0148.5 R/Y/H―
l
1125 (1080) /50p1 920 x 1 08056.350.0148.5 R/Y/H―
l
640 x 400 640 x 400
31.570.125.2 R/H― ―
640 x 400 37.985.131.5 R/H― ―
640 x 480 640 x 480
31.5 59.9 25.2  R/H
l l
640 x 480 35.0 66.7 30.2  R/H― ―
640 x 480 37.9 72.8 31.5  R/Hl l
640 x 480 37.5 75.0 31.5  R/Hl l
640 x 480 43.3 85.0 36.0  R/H― ―
800 x 600 800 x 600
35.2 56.3 36.0  R/H
l l
800 x 600 37.9 60.3 40.0  R/Hl l
800 x 600 48.1 72.2 50.0  R/Hl l
800 x 600 46.9 75.0 49.5  R/Hl l
800 x 600 53.7 85.1 56.3  R/H― ―
832 x 624 832 x 62449.774.657.3 R/Hl l
1024 x 768 1 024 x 768
39.6 50.0 51.9  R/H
― ―
1 024 x 768 48.4 60.0 65.0  R/H― ―
1 024 x 768 56.5 70.1 75.0  R/Hl l
1 024 x 768 60.0 75.0 78.8  R/Hl l
1 024 x 768 68.7 85.0 94.5  R/H― ―
1 024 x 768 81.4 100.0  113.3  R/H― ―   
						

							Chapter 7 Appendix — Technical information
ENGLISH - 157
Mode Display resolution
(dots) Scanning frequency
Dot clock 
frequency 
(MHz) Format Plug and play*
1
Horizontal 
(kHz) Vertical 
(Hz) RGB2HDMI/
DIGITAL  LINK
1152 x 864 1 152 x 864
53.7 60.0 81.6  R/H
― ―
1 152 x 864 67.5 75.0108.0  R/H― ―
1 152 x 864 77.1 85.0 119.7  R/H― ―
1152 x 870 1 152 x 87068.775.1100.0 R/Hl l
1280 x 720 1 280 x 720
37.1 49.8 60.5  R/H― ―
1 280 x 720 44.8 59.9 74.5  R/H― ―
1280 x 768 1 280 x 768
60.3 74.9 102.3  R/H― ―
1 280 x 768 68.6 84.8 117.5  R/H― ―
1280 x 800
1 280 x 80041.3 50.0 68.0  R/H― ―
1 280 x 80049.7 59.8 83.5  R/Hl*5l*5
1 280 x 80062.8  74.9 106.5  R/H― ―
1 280 x 80071.6 84.9 122.5  R/H― ―
1280 x 960 1 280 x 96060.060.0108.0 R/H― ―
1280 x 1024
1 280 x 1 02464.0 60.0108.0 R/H― ―
1 280 x 1 02480.075.0135.0 R/H― ―
1 280 x 1 02491.185.0157.5 R/H― ―
1366 x 768 1 366 x 768
39.649.9 69.0  R/H― ―
1 366 x 768 47.759.8 85.5  R/H― ―
1400 x 1050 1 400 x 1 050
65.2 
60.0 122.6  R/H― ―
1 400 x 1 05065.3 60.0 121.8  R/H― ―
1 400 x 1 05082.3 74.9156.0 R/H― ―
1440 x 900 1 440 x 90055.9 59.9106.5  R/H― ―
1600 x 900 1 600 x 900
46.449.996.5 R/H― ―
1 600 x 900 55.9 60.0 119.0  R/H― ―
1600 x 12001 600 x 1 20075.0 60.0162.0 R/Hl l
1680 x 1050 1 680 x 1 05054.1 
50.0 119.5  R/H― ―
1 680 x 1 05065.3 60.0 146.3  R/H― ―
1920 x 10801 920 x 1 08055.6 49.9 141.5  R/H― ―
1 920 x 1 080*466.6 59.9 138.5  R/H― ―
1920 x 12001 920 x 1 20061.8  49.9 158.3  R/H― ―
1 920 x 1 200*474.0 60.0 154.0  R/Hl*6l*6
*1 Signals with  l in the Plug and play columns are signals described in EDID (extended display identification data) of the projector . A signal, which 
has no l  in the Plug and play columns but has an entry in the Format column, can be input. For signals without  l in the Plug and play columns, 
resolution may not be selected in the computer even though the projector supports them.
*2  Pixel-Repetition signal (dot clock frequency 27.0 MHz) only
*3  When a 1125 (1035)/60i signal was input, it is displayed as a 1125 (1080)/60i signal. But 1125(1035)/60i HDMI signal is not supported.
*4  VESA CVT-RB (Reduced Blanking)-compliant
*5  Only for PT -EW650 and PT-EW550
*6  Only for PT -EZ590
Note
 
f The number of display dots for PT
-EZ590 is 1 920 x 1 200. The number of display dots for PT-EW650 and PT-EW550 is 1 280 x 800. The 
number of display dots for PT -EX620 and PT-EX520 is 1 024 x 768. A signal with a different resolution is converted to the number of display 
dots.
 
f The “i” at the end of the resolution indicates an interlaced signal.
 
f When interlaced signals are connected, flickering may occur on the projected image.
 
f DIGITAL LINK input compatible signal is the same as HDMI input compatible signal. 
 
(Only for PT -EZ590, 
PT-EW650 and PT-EX620)
 
f When the communication method of the DIGITAL LINK is set to [LONG REACH], the signals that the projector can receive are up to 
1080/60p(148.5MHz).
 
(Only for PT -EZ590, 
PT-EW650 and PT-EX620)
 
f Even the above signals exist, some image signals that recorded in special method may not be displayed.   
						

							Chapter 7 Appendix — Specifications
158 - ENGLISH
Specifications
The specifications of the projector are as follows.
Power supply PT
-EZ590, PT-EZ590A,  
PT-EZ590D, PT-EW650, 
PT-EW650A, PT-EW650D, 
PT -EX620, PT -EX620A, 
PT -EX620D,PT -EW550, 
PT -EW550A, PT -EW550D, 
PT -EX520, PT -EX520A, 
PT -EX520D 100 V - 240 V 
 (100 V - 240 V alternating current), 50 Hz/60 Hz
PT -EZ590T, PT-EW650T, 
PT -EX620T, PT -EW550T, 
PT -EX520T  110 V 
  (110 V alternating current), 60Hz 
Power 
consumption
ProjectingPT
-EZ590, PT-EZ590A,  
PT-EZ590D 484 W (5.5 A - 2.3 A)
PT-EW650, PT-EW650A,  
PT-EW650D, PT -EX620, 
PT -EX620A, PT -EX620D 
PT -EW550, PT -EW550A, 
PT -EW550D, PT -EX520, 
PT -EX520A, PT -EX520D 461 W (5.3 A - 2.1 A)
PT -EZ590T 484 W (4.9 A)
PT-EW650T, PT -EX620T
PT -EW550T, PT -EX520T  461 W (4.7 A)
In standby mode PT
-EZ590, PT-EZ590A,  
PT-EZ590D, PT-EW650, 
PT-EW650A, PT-EW650D, 
PT -EX620, PT -EX620A, 
PT -EX620D,PT -EW550, 
PT -EW550A, PT -EW550D, 
PT -EX520, PT -EX520A, 
PT -EX520D When [STANDBY MODE] of [ECO MANAGEMENT] is set to [ECO]: 
0.5 W
PT-EZ590T, PT-EW650T, 
PT -EX620T, PT -EW550T, 
PT -EX520T When [STANDBY MODE] of [ECO MANAGEMENT] is set to [ECO]: 
0.3 W
PT-EZ590, PT-EW650, PT-EX620 When [STANDBY MODE] of [ECO MANAGEMENT] is set to 
[NORMAL]: 12 W
When [STANDBY MODE] of [ECO MANAGEMENT] is set to 
[NORMAL], and [IN STANDBY MODE] in [AUDIO SETTING] is set to 
[ON]: 30 W
PT -EW550, PT -EX520 When [STANDBY MODE] of [ECO MANAGEMENT] is set to 
[NORMAL]: 8 W
When [STANDBY MODE] of [ECO MANAGEMENT] is set to 
[NORMAL], and [IN STANDBY MODE] in [AUDIO SETTING] is set to 
[ON]: 22 W
LCD panel Size
PT
-EZ590, PT-EW650, PT -EW5501.63 cm (0.64″) (aspect ratio 16:10)
PT -EX620,  PT -EX520 1.60 cm (0.63″) (aspect ratio 4:3)
Display system Translucent screen LCD panel 3 panels, 3 primary color system
Drive system Active matrix
Number of pixels PT
-EZ590 2 304 000 pixels (1 920 x 1 200 dots) x 3 panels
PT-EW650, PT -EW550 1 024 000 pixels (1 280 x 800 dots) x 3 panels
PT -EX620,  PT -EX520 786 432 pixels (1 024 x 768 dots) x 3 panels
Lens
*1Electric zoom PT-EZ590, PT-EW650, 
PT-EW550
1.22 ~ 2.26:1
PT-EX620, PT-EX520 1.32 ~ 2.44:1
Electric focus F = 1.6 ~ 2.2
f = 17.1 mm ~ 31.7 mm
Luminous lamp 320 W, UHM lamp   
						

							Chapter 7 Appendix — Specifications
ENGLISH - 159
Light output*2*3
PT
-EZ590 5 400 lm
PT-EW650 5 800 lm
PT -EW550 5 000 lm
PT -EX620 6 200 lm
PT -EX520 5 300 lm
Contrast ratio
*3
PT -EZ590, PT-EW650,
PT -EX620 10 000:1 (when [PICTURE MODE] is set to [DYNAMIC], [LAMP 
POWER] is set to [NORMAL], [IRIS] is set to [ON], [DAYLIGHT 
VIEW] is set to [OFF] and [AUTO POWER SAVE] is set to [OFF])
PT -EW550, PT -EX520
2 000:1 (when [PICTURE MODE] is set to [DYNAMIC], [LAMP 
POWER] is set to [NORMAL], [DAYLIGHT VIEW] is set to [OFF] and 
[AUTO POWER SAVE] is set to [OFF])
Color system 7 standards (NTSC/NTSC4.43/PAL/PAL-N/PAL-M/SECAM/PAL60)
Projected image size 1.02 m (40") - 10.16 m (400")
Screen aspect ratio PT
-EZ590, PT-EW650, PT -EW55016:10
PT -EX620,  PT -EX520 4:3
Projection method [FRONT/CEILING], [FRONT/DESK], [REAR/CEILING], [REAR/DESK]
Speaker 4.0 cm, round, x 1
Max. effective audio output 10 W (monaural)
Power cord length 3.0 m (118-1/8")
Outer case Molded plastic
Dimensions Width
498 mm (19-19/32")
Height 145 mm (5-11/16") (with legs at shortest position)
Depth PT
-EZ590, PT-EW650, 
PT -EW550,  PT -EX620, 
PT -EX520 398.3 mm (15-11/16") (including standard zoom lens)
PT -EZ590L, PT-EW650L, 
PT -EW550L, PT -EX620L,  
PT -EX520L 358 mm (14-3/32") (excluding optional lens)
Weight Approx. 8.4 k] (18.52 lbs.)
*4 (including standard zoom lens)
Approx. 7.7 k] (16.98 lbs.)
*4 (excluding optional lens)
Noise level
*335 dB when [LAMP POWER] is set to [NORMAL]
29 dB when [LAMP POWER] is set to [ECO]
Operating 
environment
Operating 
environment 
temperature
*5
0 °C (32 °F) - 45 °C (113 °F)  (Elevation: below 1 400 m (4 593'))
0 °C (32 °F) - 40 °C (104 °F)  (Elevation: 1 400 m (4 593') ~ 2 700 m (8 858'))
Operating 
environment 
humidity 20 % - 80 % (No condensation)
Remote 
control Power supply
DC 3 V (AAA/R03/LR03 battery x 2)
Operating range Within approx. 30 m (98'5") (when operated directly in front of signal receiver)
Weight 102 ] (3.6 ozs.) (including batteries)
Dimensions Width: 48 mm (1-7/8"), Height: 145 mm (5-23/32"), Depth: 27 mm (1-1/16")
*1 For PT -EZ590L, PT-EW650L, PT -EX620L, PT-EW550L, PT -EX520L, the lens is sold separately.
*2  Value is for the supplied standard zoom lens. The value varies depending on the lens.
*3  Measurement, measuring conditions and method of notation all comply with ISO/IEC 21 118:2012 international standards.
*4  Average value. Weight varies for each product.
*5  If the [PROJECTOR SETUP] menu → [LAMP POWER] is set to [NORMAL], [LAMP POWER] changes to [ECO] forcibly to protect the projector 
when the operating environment temperature becomes 40 °C (104 °F) or higher (35 °C (95 °F) or higher when using the projector at high altitudes).
Note
 
f The model numbers of accessories and optional accessories are subject to\
 change without prior notice.   
						

							Chapter 7 Appendix — Specifications
160 - ENGLISH
 
r Terminal
 terminal 1 set, (BNC x 5 (RGB/YP
BPR/YCBCR x 1))
RGB signal 0.7 V [p-p] 75 Ω (SYNC ON GREEN: 1.0 V [p-p] 75 Ω)
SYNC/HDTTL high impedance, automatic positive/negative 
polarity compatible
VD TTL high impedance, automatic positive/negative 
polarity compatible
YP
BPR signal Y: 1.0 V [p-p] including synchronization signal, PBPR: 0.7 V [p-p] 75 Ω
Y/C signal Y: 1.0 V [p-p], C: 0.286 V [p-p] 75 Ω
 terminal 1 set high-density D-Sub 15 p (female)
RGB signal
0.7 V [p-p] 75 Ω (SYNC ON GREEN: 1.0 V [p-p] 75 Ω)
SYNC/HDTTL high impedance, automatic positive/negative 
polarity compatible
VD TTL high impedance, automatic positive/negative 
polarity compatible
(The SYNC/HD and VD terminals do not support 3 value SYNC.)
YP
BPR signal Y: 1.0 V [p-p] including synchronization signal, PBPR: 0.7 V [p-p] 75 Ω
 terminal 1 set, high-density D-Sub 15 p (female)
RGB signal
0.7 V [p-p] 75 Ω (SYNC ON GREEN: 1.0 V [p-p] 75 Ω)
SYNC/HDTTL high impedance, positive/negative polarity
VD TTL high impedance, positive/negative polarity
YP
BPR signal Y: 1.0 V [p-p] including synchronization signal, PBPR: 0.7 V [p-p] 75 Ω
 terminal 1 set, pin jack 1.0 V [p-p] 75 Ω
/ 
terminal 2 sets, HDMI 19 pin, HDCP compatible, Deep Color compatible
Audio signal
Linear PCM (Sampling frequency: 48 kHz/44.1 kHz/32 kHz)
/ 
terminal 2 sets, M3 stereo mini jack 0.5 V [rms], input impedance 22 kΩ or more
 terminal 1 set, pin jack x 2 (L-R) 0.5 V [rms], input impedance 22 kΩ or more
 
terminal 1 set, M3 stereo mini jack (monitor output, stereo compatible)
0 V [rms] to 2.0 V [rms] (variable), output impedance 2.2 kΩ or less
 terminal 1 set, D-Sub 9 p, RS-232C compliant, for computer control
 terminal 1 set, D-Sub 9 p, for external control
 terminal 1 set, M3 stereo mini jack, for remote control (wired)
 terminal *11 set, RJ-45, for network, DIGITAL LINK connection, PJLink compatible, 100Base-TX
 terminal1 set, RJ-45, for network connection, PJLink compatible, 10Base-T/100Base-TX
 terminalUSB connector (type A) x 1, for the Wireless module (Model No.: ET-WML100) only
 terminalUSB connector (type A) x 1, for power supply only (DC 5 V, maximum 900 mA)
*1  Only for PT-EZ590, PT-EW650 and PT-EX620
 
r Applicable scanning frequency
Refer to “List of compatible signals” (
x page 156) for the types of video signals that can be used with the 
projector.
For video signal Horizontal : 15.73 kHz Vertical : 59.94 Hz, Horizontal : 15.63 kHz Vertical : 50 Hz
For Y/C signal Horizontal : 15.73 kHz Vertical : 59.94 Hz, Horizontal : 15.63 kHz Vertical : 50 Hz
For RGB signal  
f Displayable resolution: 640 x 400 to 1 920 x 1 200
 
f Dot clock frequency: 162 MHz or less
For YC
BCR/YPBPR signal  
f Displayable resolution: 480i/576i to 1 920 x 1 080
 
f Dot clock frequency: 148.5 MHz or less
 
f The SYNC/HD and VD terminals do not support 3 value SYNC.
For HDMI signal  
f Displayable resolution for movie-based signals: 480i/576i
*1 to 1 920 x 1 080 
Displayable resolution for still image signals: 640 x 400 to 1 920 x 1 200 (non-interlaced)
 
f Dot clock frequency: 25 MHz - 162 MHz
*1  Pixel-Repetition signal (dot clock frequency 27.0 MHz) only
Note
 
f DIGITAL LINK input compatible signal is the same as HDMI input compatible signal.
 
(Only for PT-EZ590, PT-EW650 and PT-EX620)