Epson Projector PT EZ590 User Manual

							Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 101
 
f The 
[SCHEDULE]  screen is displayed.
3)  Press as to select [PROGRAM EDIT].
4)  Press qw to select a program number, and press the  button.
5)  Press as to select a command number, and press the  button.
6)  Press asqw  to select [TIME], and press the  button.
 
f The projector is in the adjustment mode (where the time is blinking).
7)  Press qw to select “hour” or “minute”, and press  as to set a time, and then press the  
button.
8)  Press asqw  to select [COMMAND].
9)  Press the  button.
 
f The 
[COMMAND]  detailed screen is displayed.
10)  Press as to select a [COMMAND].
 
f For [COMMAND] which requires detailed settings, the items of the detailed settings will switch each time 
you press 
qw.
 
f When [INPUT] is selected, press the  button, and then press 
as to select the input to be set.
[COMMAND] Detailed settings of 
[COMMAND] Description
[POWER ON] ―Switches on the projector.
[STANDBY] ―Enters standby.
[SHUTTER] 
*1[OPEN] Disables the shutter function (shutter: open).
[CLOSE] Enables the shutter function (shutter: closed).
[AV MUTE] 
*2[OFF] Cancels the AV mute.
[ON] The image and the audio disappear.
[INPUT] [NETWORK]
Switches the input to NETWORK.
[RGB1] Switches the input to RGB1.
[RGB2] Switches the input to RGB2.
[HDMI1] Switches the input to HDMI1.
[HDMI2] Switches the input to HDMI2.
[VIDEO] Switches the input to VIDEO.
[DIGITAL LINK]
*1Switches the input to DIGITAL LINK.
[INPUT1] - [INPUT10]
*3Switches the input to DIGITAL LINK, and switch the input of the 
Panasonic twisted-pair-cable transmitter to the specified input.
[LAMP POWER] [NORMAL]
Sets the lamp brightness to high luminance.
[ECO] Sets the lamp brightness to low luminance.
[IN STANDBY MODE] [OFF]
Audio output is stopped during standby.
[ON] Audio is output during standby.
[VOLUME] [0] ~ [63]Sets the volume.
*1 For PT-EZ590, PT-EW650 and PT-EX620
*2  For PT-EW550 and PT-EX520
*3  When the optional DIGITAL LINK output supported device (Model No.: ET -YFB100G, ET-YFB200G) is connected to the projector, its input 
name is automatically reflected from [INPUT1] to [INPUT10]. If an item where the input name is not reflected is selected, it is disabled.
11)  Press the  button.
 
f The command is fixed and 
n is displayed at the left of the selected command.
12)  Press asqw  to select [STORE], and press the  button.
Note
 
f If you attempt to register the setting that would make the lamp turn on for a short time, an error message will be displayed on the screen. Set 
the time and the command again. 
 
f To delete a command that has been already set, press the  button on the remote control while the screen in Step 
5) is 
displayed, or select [DELETE] at the screen in Step  6) and press the  button.
 
f If multiple commands have been set for the same time, they are executed in chronological order starting from the smallest command 
number.
 
f The operating time will be the local time. (
x page 102)   
						

							Chapter 4 Settings — [PROJECTOR SETUP] menu
102 - ENGLISH
 
f If an operation is executed with the remote control or the control panel of the projector or with a control command before the command set in 
[SCHEDULE] is executed, the command set with the schedule function may not be executed.
[DATE AND TIME]
Set the time zone, date, and time of the built-in clock of the projector
.
Setting the time zone
1) Press as to select [DATE AND TIME].
2)  Press the  button.
 
f The 
[DATE AND TIME]  screen is displayed.
3)  Press as to select [TIME ZONE].
4)  Press qw to switch [TIME ZONE].
Setting the date and time manually
1) Press as to select [DATE AND TIME].
2)  Press the  button.
 
f The 
[DATE AND TIME]  screen is displayed.
3)  Press as to select [ADJUST CLOCK].
4)  Press the  button.
 
f The 
[ADJUST CLOCK]  screen is displayed.
5)  Press as to select an item, and press  qw to set the local date and time.
6)  Press as to select [OK], and press the  button.
 
f The setting of the date and time will be completed.
Setting the date and time automatically
1) 
Press as to select [DATE AND TIME].
2)  Press the  button.
 
f The 
[DATE AND TIME]  screen is displayed.
3)  Press as to select [ADJUST CLOCK].
4)  Press the  button.
 
f The 
[ADJUST CLOCK]  screen is displayed.
5)  Press as to select [NTP SYNCHRONIZATION], and press  qw to change the setting to [ON].
6)  Press as to select [OK], and press the  button.
 
f The setting of the date and time will be completed.
Note
 
f To set the date and the time automatically, the projector must be connected to the network.
 
f If synchronization with the NTP server fails just after [NTP SYNCHRONIZATION] is turned [ON], [NTP SYNCHRONIZATION] will return to 
[OFF]. Also if [NTP SYNCHRONIZATION] is turned [ON] while the NTP server is not set, [NTP SYNCHRONIZATION] will return to [OFF].
 
f Access the projector via a web browser to set the NTP server. Refer to “[Adjust clock] page” (
x page 130) for details.
 
f The [TIME ZONE] setting is reset to the factory default when [INITIALIZE 
ALL] is executed from the [PROJECTOR SETUP] menu (
x page 
103). However, the date and the time based on the local date and the time setting (Coordinated Universal Time, UTC, Universal Time, 
Coordinated) will be maintained without being initialized.
[LENS CALIBRATION]
Detect the lens shift limit value of the projector and set the home position automatically .
1)  Press as to select [LENS CALIBRATION].   
						

							Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 103
2) 
Press the  button.
 
f The confirmation screen is displayed.
3)  Press qw to select [OK], and press the  button.
 
f To cancel, select [CANCEL].
 
f The lens moves up, down, left, and right to automatically detect the lens shift limit value, and automatically 
set the home position.
 
f The lens stops to complete the calibration.
Note
 
f [NOW CALIBRATING...] is displayed during lens calibration. Cannot cancel mid-operation.
 
f When lens calibration executes correctly, [COMPLETE] is displayed and [INCOMPLETE] is displayed when it does not execute correctly.
[INITIALIZE ALL]
Return various setting values to their factory default settings.
1) 
Press as to select [INITIALIZE ALL].
2)  Press the  button.
 
f The 
[INITIALIZE ALL]  screen is displayed.
3)  When the confirmation screen is displayed, press  qw to select [OK] and then press the  
button.  
f The
 [NOW INITIALIZING...]  screen is displayed and then the  [POWER OFF.] screen will be displayed.
4)  Press the  button.
 
f The operation of other buttons is disabled.
 
f The focus adjustment screen and the initial setting (display language) screen will be displayed successively 
when the projector is switched on the next time.
Note
 
f The projector will enter the standby status to reflect the setting values when [INITIALIZE 
ALL] is executed.
 
f When [INITIALIZE ALL] is executed, [STANDBY MODE], [EMULATE], [FILTER COUNTER] and the setting values of [NETWORK] cannot be 
returned to the factory default values. 
 
For details about the initialization of [NETWORK], please refer to [NETWORK] → [INITIALIZE]. (
Æ page 110) 
[SERVICE PASSWORD]
This function is used by a service person.   
						

							Chapter 4 Settings — [SECURITY] menu
104 - ENGLISH
[SECURITY] menu
On the menu screen, select [SECURITY] from the main menu, and select an \
item from the sub-menu.
Refer to “Navigating through the menu” (
x page 62) for the operation of the menu screen.
 
f When the projector is used for the first time
Initial password: Press 
awsqawsq in order, and press the  button.
Attention
 
f When you select the [SECURITY] menu and press the  button, entering a password is required. Enter the preset password and 
then continue operations of the [SECURITY] menu.
 
f When the password has been changed previously, enter the changed password, and press the  button.
Note
 
f The entered password is displayed with * marks on the screen.
 
f An error message is displayed on the screen when the entered password is incorrect. Re-enter the correct password.
[PASSWORD]
The 
[PASSWORD]  screen is displayed when turning the  switch to  and turning on the 
power. When the entered password is incorrect, the operation will be restricted to the power < v/
b > button and the 
 (,  and ) buttons.
1)  Press as to select [PASSWORD].
2)  Press qw to switch the item.
 
f The items will switch each time you press the button.
[OFF]
Disables the security password entry.
[ON] Enables the security password entry.
Note
 
f The [PASSWORD] setting is set to [OFF] by the factory default or when [INITIALIZE ALL] in [PROJECTOR SETUP] menu (
x page 103) is 
executed.
 
f Change the password periodically that is hard to guess.
 
f The security password is enabled after setting [PASSWORD] to [ON] and turning the  switch to .
[PASSWORD CHANGE]
Change the security password.
1) 
Press as to select [PASSWORD CHANGE].
2)  Press the  button.
 
f The 
[PASSWORD CHANGE]  screen is displayed.
3)  Press asqw  and the number ( - ) buttons to set the password.
 
f Up to eight button operations can be set.
4)  Press the  button.
5)  Re-enter the password for the confirmation.
6)  Press the  button.
Note
 
f The entered password is displayed with * marks on the screen.
 
f An error message is displayed on the screen when the entered password is incorrect. Re-enter the correct password.
 
f If numbers have been used for the security password, the security password will need to be initialized again if the remote control is lost. 
Consult your dealer for the initialization method.
[DISPLAY SETTING]
Overlap the security message (text or image) over the projecting image.
1) 
Press as to select [DISPLAY SETTING].
2)  Press qw to switch the item.   
						

							Chapter 4 Settings — [SECURITY] menu
ENGLISH - 105
 
f The items will switch each time you press the button.
[OFF]
Hides the security message.
[TEXT] Displays the text set in the [SECURITY] menu → [TEXT CHANGE].
[USER LOGO] Displays the image registered by the user.
Note
 
f To create/register the [USER LOGO] image, use “Logo Transfer Software” included in the supplied CD-ROM.
[TEXT CHANGE]
Edit the text to be displayed when [TEXT] is selected in [DISPLA
Y SETTING].
1)  Press as to select [TEXT CHANGE].
2)  Press the  button.
 
f The 
[TEXT CHANGE]  screen is displayed.
3)  Press asqw  to select the text, and press the  button to enter the text.
4)  Press asqw  to select [OK], and press the  button.
 
f The text is changed.
[MENU LOCK]
Display the menu by the  button and set whether or not to enable menu operations.
1) 
Press as to select [MENU LOCK].
2)  Press qw to switch the item.
 
f The items will switch each time you press the button.
[OFF]
Unlocks menu operations.
[ON] Locks menu operations.
Note
 
f When the entered password is incorrect after setting [MENU LOCK] to [ON], the  button cannot be operated.
 
f [MENU LOCK] is set to [OFF] at the time of purchase or when [INITIALIZE 
ALL] is executed.
 
f When [MENU LOCK] is set to [ON], after entering the password to release the lock, the unlock state is held until the projector enters the 
standby mode.
[MENU LOCK PASSWORD]
The menu lock password can be changed.
1) 
Press as to select [MENU LOCK PASSWORD].
2)  Press the  button.
 
f The 
[MENU LOCK PASSWORD]  screen is displayed.
3)  Press asqw  to select the text, and press the  button to enter the text.
 
f Up to 16 characters can be input.
4)  Press asqw  to select [OK], and press the  button.
 
f To cancel, select [CANCEL].
Attention
 
f The initial password is “AAAA” at the time of purchase or when [INITIALIZE 
ALL] is executed.
 
f Change the password periodically that is hard to guess.
[CONTROL DEVICE SETUP]
Enable/disable the button operations on the control panel and the remote control.
1) 
Press as to select [CONTROL DEVICE SETUP].   
						

							Chapter 4 Settings — [SECURITY] menu
106 - ENGLISH
2) 
Press the  button.
 
f The 
[CONTROL DEVICE SETUP]  screen is displayed.
3)  Press as to select [CONTROL PANEL] or [REMOTE CONTROLLER].
[CONTROL PANEL] You can set the limitation on the control from the control panel.
[REMOTE CONTROLLER] You can set the limitation on the control from the remote control.
4) Press qw to switch between [ENABLE] and [DISABLE]. 
 
f You can set the limitation on the control by the control panel or the rem\
ote control.
[ENABLE]
Enable the button operations.
[DISABLE] Disable the button operations.
 
f A confirmation screen will be displayed when you change [ENABLE] to [DISABLE], then proceed to Step 
5).
5)  Press qw to select [OK], and then press the  button.
Note
 
f When a button operation is performed on the device set to [DISABLE] , the [P
ASSWORD] screen is displayed. 
To continue operations, enter the security password.
 
f The [PASSWORD] screen will disappear when there is no operation for approx. 10 seconds.
 
f If the operations of both [CONTROL PANEL] and [REMOTE CONTROLLER] are set to [DISABLE], the projector cannot be turned off (cannot 
enter standby).
 
f Even when you set button operations on the remote control to be disabled, operations of the  and  buttons on the remote 
control are enabled.   
						

							Chapter 4 Settings — [NETWORK] menu
ENGLISH - 107
[NETWORK] menu
On the menu screen, select [NETWORK] from the main menu, and select an i\
tem from the sub-menu.
Refer to “Navigating through the menu” (
x page 62) for the operation of the menu screen.
Note
 
f The on-screen menu (menu screen) of the projector has not the network setting about the wireless LAN. When the wireless module (Model 
No.: ET-WML100) of the optional accessories is inserted to the projector, please set the wireless LAN by accessing the projector via a 
computer. For detailed, please refer to “Web control function” → “[Network config] page” → “Wireless LAN” (
x page 126).
[DIGITAL LINK MODE]
(Only for PT
-EZ590, PT-EW650 and PT -EX620)
Switch the communication method of the  terminal of the projector.
1)  Press as to select [DIGITAL LINK MODE].
2)  Press qw to switch the item.
 
f The items will switch each time you press the button.
[AUTO]
Switches the communication method automatically to DIGITAL LINK, long reach or Ethernet.
[DIGITAL LINK] Fixes the communication method to DIGITAL LINK.
[LONG REACH] Fixes the communication method to long reach.
[ETHERNET] Fixes the communication method to Ethernet.
Possible communication modes
l: Communication possible
―: Communication not possible
Setting Communication possible
Image transmission (100 m (328 '1"))Image transmission
(150 m (492 '2")) Ethernet
RS-232C
[AUTO] For DIGITAL LINK
l―
ll
For long reach ―
lll
For Ethernet ――
l―
[DIGITAL LINK] l―
ll
[LONG REACH] ―
lll
[ETHERNET] ――
l―
Note
 
f The maximum transmission distance when connected with the long-reach communication method is 150 m (492'2"). However
, the signal 
that the projector can receive is only up to 1080/60p (1 920 x 1 080 dots, dot clock frequency: 148.5 MHz).
 
f When the communication method of the twist-pair-cable transmitter is set to long reach, it will connect with long-reach communication 
method when [DIGITAL LINK MODE] is set to [AUTO]. To connect with the optional DIGITAL LINK Switcher (Model No.: ET
-YFB200G) with 
the long-reach communication method, set [DIGITAL LINK MODE] to [LONG REACH].
 
f It will not connect correctly if the twist-pair-cable transmitter is not supporting the long-reach communication method even if [DIGIT
AL LINK 
MODE] is set to [LONG REACH].
[DIGITAL LINK STATUS]
(Only for PT -EZ590, PT-EW650 and PT -EX620)
Display DIGITAL LINK connection environment.
1)  Press as to select [DIGITAL LINK STATUS].
2)  Press the  button.
 
f The 
[DIGITAL LINK STATUS]  screen is displayed.
[LINK STATUS] Either [NO LINK], [DIGITAL LINK], [LONG REACH] or [ETHERNET] is displayed.
[HDCP STATUS] Either [NO SIGNAL], [OFF], or [ON] is displayed.   
						

							Chapter 4 Settings — [NETWORK] menu
108 - ENGLISH
[SIGNAL QUALITY] [SIGNAL QUALITY] is a numerical value of the amount of error, and the display color changes to 
green, yellow, or red depending on that value.
Check the signal quality level while receiving a signal from the twisted-pair-cable transmitter
.
 
f MAX/MIN: Maximum/minimum value of the amount of error. 
 
f Green (-12 dB or lower) 
→ Normal signal quality level.
 
f Yellow (
-11 to -8 dB) 
→ Warning level where there is the possibility of noise introduced on the 
screen.
 
f Red (
-7 dB or higher) 
→ Abnormal level where synchronization may be interrupted or a signal may 
not be received.
[DIGITAL LINK MENU]
(Only for PT -EZ590, PT-EW650 and PT -EX620)
When the optional DIGITAL LINK output supported device (Model No.: ET -YFB100G, ET-YFB200G) is connected 
to the  terminal, the main menu of DIGITAL LINK output supported device is displayed.
Refer to the Operating Instructions of the DIGITAL LINK output supported device for details.
Note
 
f When [NETWORK] menu → [NETWORK CONTROL] → [EXTRON XTP] is set to [ON], [DIGIT
AL LINK MENU] cannot be selected.
[WIRED LAN]
You can make detailed wired LAN settings.
1) Press as to select [WIRED LAN].
2)  Press the  button.
 
f The
 [WIRED DETAILED SETUP]  screen is displayed.
3)  Press as to select an item, and change the setting according to the instructions\
.
[DHCP]  [ON]
If a DHCP server exists in the network to which the 
projector is connected, the IP address will automatically be 
acquired.
[OFF] If a DHCP server does not exist in the network to which 
the projector is connected, additionally set [IP ADDRESS], 
[SUBNET MASK] and [DEFAULT GATEWAY].
[IP ADDRESS]  Enter the IP address if DHCP server is not used.
[SUBNET MASK] Enter the subnet mask if DHCP server is not used.
[DEFAULT GATEWAY]  Enter the gateway address if DHCP server is not used.
[DNS1] Enter the preferred DNS server address if DHCP server is not used.
[DNS2] Enter the alternate DNS server address if DHCP server is not used.
4)  Press as  to select [OK], and press the  button.
 
r Default settings of [WIRED LAN]
 
f The following settings are set before the projector leaves the factory
.
[DHCP]OFF
[IP ADDRESS] 192.168.10.100
[SUBNET MASK] 255.255.255.0
[DEFAULT GATEWAY] 192.168.10.1
[DNS1]/[DNS2] NONE
Note
 
f Before using the DHCP server, make sure the DHCP server is already functioning.
 
f Consult your network administrator regarding the IP ADDRESS, SUBNET MASK and DEFAULT GATEWAY.
 
f The settings of network are same for both the  terminal and the  terminal.
[PROJECTOR NAME]
Change the name as desired in such a case as the projector needs to be identified on application software.
1) Press as to select [PROJECTOR NAME].   
						

							Chapter 4 Settings — [NETWORK] menu
ENGLISH - 109
2) 
Press the  button.
 
f The 
[PROJECTOR NAME]  screen is displayed.
3)  Select characters with the asqw  buttons and press the  button to enter the projector 
name.   
f Up to eight characters can be input.
 
f Select [ALL DELETE] to delete all the entered characters, or press the  button on the remote 
control to delete a character on the cursor in the entry field. 
 
4) 
Select [OK] with the  as buttons and press the  button. 
 
f To cancel the change of the name, press 
asqw to select [CANCEL] and press the  button.
Note
 
f [Name 
ØØØØ ] (
ØØØØ
 is 4-digit number) is set before the projector leaves the factory
.
[NETWORK CONTROL]
Set up the control method of the network.
1) Press as to select [NETWORK CONTROL].
2)  Press the  button.
 
f The 
[NETWORK CONTROL]  screen is displayed.
3) Press as to select an item, and press  qw to change the setting.
[WEB CONTROL]Set to [ON] to control with the web browser.
[PJLink CONTROL] Set to [ON] to control with the PJLink protocol.
[COMMAND CONTROL] Set to [ON] to control with the  terminal control command format (
x page 151). Refer 
to “Control commands via LAN” ( x page 148).
[COMMAND PORT] Set the port number used for command control.
[Crestron Connected(TM)] Set to [ON] to control with Crestron Connected
TM of Crestron Electronics, Inc.
[AMX D.D.] Set to [ON] to control with the controller of AMX Corporation.
Setting this function to [ON] enables detection through “AMX Device Discovery”. For details, refer to 
the website of AMX Corporation.
URL http://www.amx.com/
[EXTRON XTP] 
*1
Set to [ON] when connecting the “XTP transmitter” of Extron Electronics to the  
terminal.
The [EXTRON XTP] setting must be set to [OFF] when connecting the optional DIGIT AL LINK output 
supported device (Model No.: ET -YFB100G, ET-YFB200G).
For details of the “XTP transmitter”, refer to the website of Extron Electronics.
URL http://www.extron.com/
*1  Only for PT-EZ590, PT-EW650 and PT-EX620
4)  Press as to select [OK], and press the  button.
 
f The current network control settings is saved.
[NETWROK STATUS]
Display the status of the projector network.
1) 
Press as to select [NETWORK STATUS].
2)  Press the  button.
 
f The 
[NETWORK STATUS]  screen is displayed.
 
f The display screen (1/2 [WIRED LAN] → 2/2 [WIRELESS LAN]/[Presenter Light]) will change each time you 
press 
as.
[WIRED LAN] [DHCP]
Displays the usage state of the DHCP server.
[IP ADDRESS] Displays the IP address.
[SUBNET MASK] Displays the subnet mask.
[DEFAULT GATEWAY] Displays the default gateway.
[DNS1] Displays the address of the preferred DNS server.
[DNS2] Displays the address of the alternate DNS server.
[MAC ADDRESS] Displays the MAC address.   
						

							Chapter 4 Settings — [NETWORK] menu
110 - ENGLISH
[WIRELESS LAN] [SSID]*1Displays the character string of SSID.
[IP ADDRESS]*1Displays the IP address.
[Presenter Light] [LOGIN PASSWORD]Displays the login password for Presenter Light/VueMagic used.
*1 The [SSID]/[IP ADDRESS] of [WIRELESS LAN] will be displayed when the wireless module (Model No.: ET-WML100) of the optional accessories is 
inserted. 
Note
 
f The settings of network are same for both the  terminal and the  terminal.
 
f The on-screen menu (menu screen) of the projector has not the network setting about the wireless LAN. When the wireless module (Model 
No.: ET-WML100) of the optional accessories is inserted to the projector, please set the wireless LAN by accessing the projector via a 
computer. For details, please refer to "Web control function" → "[Network config] page" → "Wireless LAN" (
x page 126).
[INITIALIZE] 
This function is used to return various setting values of [NETWORK] to the factory default value.
1) 
Press as to select [INITIALIZE].
2)  Press the  button.
 
f The 
[INITIALIZE]  screen is displayed.
3)  Press qw to select [OK] and then press the  button.