Epson Projector PowerLite Pro G6770WU User Manual

							Parent topic:
Attaching and Removing a Lens
Attaching and Removing the Cable Cover You can attach the cable cover that came with your projector to hide the attached cables from view.
1. Bundle the cables together using a band or other fastener (not provided).
2. Place the cable cover on the projector as shown, guiding the cables through the notch on the base ofthe cable cover.
51   
						

							3. Tighten both cable cover screws.
To remove the cover, loosen both screws and pull the cover off of the projector.
Parent topic:
Setting Up the Projector
Attaching and Removing the Cable Clips You can install the cable clips that came with your projector to provide additional support to the power
and HDMI cables.
Note:The PowerLite Pro G6070W/G6170/G6270W/G6470WU/G6570WU/G6770WU come with one
cable clip.
1. Connect the power and HDMI cables to the projector.
52  
						

							2. Insert the end of the cable clip anchors into the cable clip slots near the power inlet and
HDMIport.
1 Cable clip slot
2 Cable clip anchor
3 Cable clip
3. Place the open cable clips around the power and HDMI cables, but dont lock them into place.
4. Slide each cable clip onto the anchors and lock the clips onto the power and HDMI connectors as shown.
To remove the cable clips, open the clips and disconnect the cables. Then pinch the sides of each cable
clip anchor and carefully pull them out of the cable clip slots.
Parent topic: Setting Up the Projector
Related tasks
Connecting to a Computer for HDMI Video and Audio
Connecting to an HDMI Video Source
Installing Batteries in the Remote Control The remote control uses the two AA batteries that came with the projector.
53  
						

							Caution:
Use only the type of batteries specified in this manual. Do not install batteries of different types,
or mix new and old batteries.
1. Remove the battery cover.
2. Insert the batteries with the +and –ends facing as shown.
54   
						

							3. Replace the battery cover and press it down until it clicks into place.
Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat
or flame. Keep batteries out of the reach of children; they are choking hazards and are very
dangerous if swallowed.
Parent topic: Setting Up the Projector
55  
						

							Using the Projector on a Network
Follow the instructions in these sections to set up your projector for use on a network.
Wired Network Projection
Wireless Network Projection
Registering a Digital Certificate on the Projector
Setting Up Projector Network E-Mail Alerts
Setting Up Monitoring Using SNMP
Selecting Other Network Settings
Controlling a Networked Projector Using a Web Browser
Crestron RoomView Support
Wired Network Projection You can send images to your projector through a wired network (PowerLite Pro
G6070W/G6170/G6270W/G6470WU/G6570WU/G6770WU). To do this, you connect the projector to
your network, and then set up your projector and computer for network projection.
After connecting and setting up the projector as described here, install the network software from the
Epson Projector Software CD or download the software as necessary. Use the following software and
documentation to set up, control, and monitor network projection:
• EasyMP Network Projection software sets up your computer for network projection (PowerLite Pro G6070W/G6170/G6270W/G6470WU/G6570WU/G6770WU). See the EasyMP Network Projection
Operation Guide for instructions.
• EasyMP Monitor software (Windows only) lets you monitor and control your projector through the network. You can download the latest software and documentation from the Epson web site. Go to
epson.com/support (U.S.) orepson.ca/support (Canada) and select your projector.
• EasyMP Network Updater software (Windows only) allows you to update firmware for a projector over a wired LAN. See the EasyMP Network Updater Operation Guide for instructions. You can download
the latest software and documentation from the Epson web site. Go to epson.com/support(U.S.) or
epson.ca/support (Canada) and select your projector.
• Projection from iOS or Android devices using the free Epson iProjection app (if your projector is connected via a LAN cable to a network that includes a wireless access point) [PowerLite Pro
G6070W/G6170/G6270W/G6470WU/G6570WU/G6770WU]; visit epson.com/projectorapp(U.S.) or
epson.ca/projectorapp (Canada) for more information.
56 
						

							Note:
If your projector is connected via a LAN cable to a network that includes a wireless access point,
you can connect to the projector wirelessly through the access point using the EasyMP Network
Projection software (PowerLite Pro G6070W/G6170/G6270W/G6470WU/G6570WU/G6770WU).
Connecting to a Wired Network
Selecting Wired Network Settings
Parent topic: Using the Projector on a Network
Connecting to a Wired Network To connect the projector to a wired local area network (LAN), use a 100Base-TX or 10Base-T network
cable. To ensure proper data transmission, use a Category 5e shielded cable or better.
1. Connect one end of the network cable to your network hub, switch, or router.
2. Connect the other end of the cable to the projectors LANport.
Parent topic: Wired Network Projection
Selecting Wired Network Settings Before you can project from computers on your network, you must select the network settings for the
projector using its menu system.
Note:Make sure you already connected the projector to your wired network using the LANport.
1. Turn on the projector.
2. Press the Menubutton.
57  
						

							3. Select the
Networkmenu and press Enter.
4. Select Network Configuration and pressEnter.
5. Select the Basicmenu and press Enter.
58 
						

							6. Select the following basic options as necessary:
•Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the
projector over the network.
• Web Remote Password (PowerLite Pro
G6070W/G6170/G6270W/G6470WU/G6570WU/G6770WU) or Web Control Password
(PowerLite Pro G6870/G6970WU) lets you enter a password up to 8 alphanumeric characters
long for accessing the projector over the web. (Default user name is EPSONWEB; default
password is admin.)
• Projector Keyword (PowerLite Pro G6070W/G6170/G6270W/G6470WU/G6570WU/G6770WU)
lets you turn on a security password to prevent access to the projector by anyone not in the room
with it. You must enter a displayed, randomized keyword from a computer using the EasyMP
Network Projection software to access the projector.
Note: Use the displayed keyboard to enter the name, passwords and keyword. Press the arrow
buttons on the remote control to highlight characters and press Enterto select them.
7. Select the Wired LANmenu and press Enter.
8. Select your IP Settings as necessary: • If your network assigns addresses automatically, turn on the DHCPsetting.
59 
						

							• If you must set addresses manually, turn off
DHCPand enter the projectors IP Address,Subnet
Mask, and Gateway Address as needed.
Note: To highlight the numbers you want from the displayed keyboard, press the arrow buttons on
the remote control. To select a highlighted number, press Enter.
9. To prevent display of the IP address on the standby screen, turn off IP Address Display.
10. When you finish selecting settings, select Setup completeand follow the on-screen instructions to
save your settings and exit the menus.
Parent topic: Wired Network Projection
Wireless Network Projection You can send images to your projector through a wireless network (PowerLite Pro
G6070W/G6170/G6270W/G6470WU/G6570WU/G6770WU). To do this, you must install the optional
Epson 802.11b/g/n wireless LAN module, and then set up your projector and computer for wireless
projection.
Note:If your projector is connected via a LAN cable to a network that includes a wireless access point,
you can connect to the projector wirelessly through the access point using the EasyMP Network
Projection software without the need for the optional wireless module.
After installing the module and setting up the projector, install the network software from the Epson
Projector Software CD or download the software, as necessary. Use the following software and
documentation to set up, control, and monitor wireless projection:
• EasyMP Network Projection software sets up your computer for wireless network projection. See the EasyMP Network Projection Operation Guide for instructions.
• EasyMP Monitor software (Windows only) lets you monitor and control your projector through the network. You can download the latest software and documentation from the Epson web site. Go to
epson.com/support (U.S.) orepson.ca/support (Canada) and select your projector.
• EasyMP Multi PC Projection software allows you to hold interactive meetings by projecting the computer screens of users over a network. See the EasyMP Multi PC Projection Operation Guidefor
instructions.
• Projection from iOS or Android devices with the wireless LAN module and free Epson iProjection app; visit epson.com/projectorapp (U.S.) orepson.ca/projectorapp (Canada) for more information
Installing the Wireless LAN Module
Using Quick Wireless Connection (Windows Only)
60