Epson Projector PowerLite Pro G6770WU User Manual

							Parent topic:
Using Basic Projector Features
Related tasks
Turning On the Projector
Turning Off the Projector Before turning off the projector, shut down any computer connected to it so you can see the computer
display during shutdown.
Note:Turn off this product when not in use to prolong the life of the projector. Lamp life will vary
depending upon mode selected, environmental conditions, and usage. Brightness decreases over time.
1. Press the power button on the projector or the Standbybutton on the remote control.
2. If you see a shutdown confirmation screen, press the power button on the projector or the Standby
button on the remote control again. (To leave the projector on, press any other button.)
The projector beeps twice, the lamp turns off, and the power light turns orange.
Note: With Epsons Instant Off technology, there is no cool-down period so you can pack up the
projector for transport right away (if necessary).
3. To transport or store the projector, make sure the power light is orange (but not flashing), then unplug the power cord.
Caution: To avoid damaging the projector or lamp, never unplug the power cord when the power
light is green or flashing orange.
Parent topic: Using Basic Projector Features
91 
						

							Selecting the Language for the Projector Menus
If you want to view the projectors menus and messages in another language, you can change the
Language setting.
1. Turn on the projector.
2. Press theMenubutton.
3. Select the Extendedmenu and press Enter.
4. Select the Languagesetting and press Enter.
5. Select the language you want to use and press Enter.
6. Press MenuorEsc to exit the menus.
Parent topic: Using Basic Projector Features
Resizing the Image with the Zoom Ring 1. Turn on the projector and display an image. Wait 30 minutes after turning on the projector beforesetting the focus, zoom, and lens shift for maximum accuracy.
Note: You can display a pattern to aid in adjusting the projected image using the Settings menu.
92 
						

							Note:
You can also display a pattern to aid in adjusting the projected image using the Test Pattern
button on the remote control.
2. To enlarge or reduce the image size, rotate the projectors zoom ring.
Parent topic: Using Basic Projector Features
Related references
Projector Setup Settings - Extended Menu
Related tasks
Displaying a Test Pattern
Focusing the Image Using the Focus Ring 1. Turn on the projector and display an image. Wait 30 minutes after turning on the projector beforesetting the focus, zoom, and lens shift for maximum accuracy.
Note: You can display a pattern to aid in adjusting the projected image using the Settings menu.
Note: You can also display a pattern to aid in adjusting the projected image using the Test Pattern
button on the remote control.
93  
						

							2. To sharpen the image focus, rotate the projector’s focus ring.
Focusing the Image with the Optional Short Throw Lens
Parent topic:
Using Basic Projector Features
Related references
Projector Setup Settings - Extended Menu
Related tasks
Displaying a Test Pattern
Focusing the Image with the Optional Short Throw Lens If you installed the optional short throw lens (ELPLU01) and used the lens shift option to shift the lens,
you can focus the image using the distortion and focus rings.
1. Turn on the projector and display an image.
Note: You can display a pattern to aid in adjusting the projected image using the Settings menu.
Note: You can also display a pattern to aid in adjusting the projected image using the Test Pattern
button on the remote control.
94  
						

							2. Carefully rotate the distortion ring all the way counter-clockwise.
Note: Be careful not to shift the short throw lens when adjusting it to prevent the projected image
from shifting.
3. Support the front of the lens with one hand and use the other to carefully rotate the focus ring until the center of the image is focused.
95   
						

							4. Rotate the distortion ring until the edges of the image are also focused.
5. Rotate the focus ring again to focus the entire screen image.
6. If the center of the image out of focus, rotate the distortion ring again to bring the area into focus.
Parent topic:
Focusing the Image Using the Focus Ring
Related references
Projector Setup Settings - Extended Menu
Related tasks
Displaying a Test Pattern
Setting the Lens Type You can select the model number for the attached lens.
1. Turn on the projector and display an image.
2. Press theMenubutton.
3. Select the Extendedmenu and press Enter.
4. Select Operation and pressEnter.
5. Select Lens Type and pressEnter.
96  
						

							You see this screen:
6. Select your model number and press Enter.
7. Press the Menubutton to accept the changes.
Parent topic: Using Basic Projector Features
Setting the Screen Type You can use the Screen Type setting to match the aspect ratio of the displayed image to the screen you
are using.
1. Turn on the projector and display an image.
2. Press theMenubutton.
3. Select the Extendedmenu and press Enter.
4. Select Display>Screen >Screen Type.
You see this screen:
5. Select your screens aspect ratio and press Enter.
6. Press the Menubutton to accept the changes.
97 
						

							7. Adjust the aspect ratio for the projected image, if necessary.
Parent topic:
Using Basic Projector Features
Related concepts
Image Aspect Ratio
Adjusting the Image Position Using Screen Position You can adjust the image position if there are margins between the edge of the image and the projected
screen frame.
Note:You cannot adjust the screen position if the Screen Type is set to 16:10for a WXGA/WUXGA
projector model or 4:3for a XGA projector model.
1. Turn on the projector and display an image.
2. Press the Menubutton.
3. Select the Extendedmenu and press Enter.
4. Select Display>Screen >Screen Position.
5. Use the arrow buttons on the remote control or projector to adjust the position of the image.
6. When you are finished, press the Menubutton.
Parent topic: Using Basic Projector Features
Related tasks
Setting the Screen Type
98  
						

							Setting the Screen Type
Adjusting the Image Position Using Lens Shift If you cannot install the projector directly in front of the screen, you can adjust the position of the
projected image using the lens shift feature.
Follow these guidelines when using lens shift to adjust your images:
• When adjusting the image height, position the image lower than where you want it to be and thenmove it up using the vertical lens shift dial. This helps prevent the image from moving down after
adjustment.
• Keep the vertical and horizontal lens shift dials in their center positions for the clearest picture.
Note: Wait 30 minutes after turning on the projector before setting the focus, zoom, and lens shift for
maximum accuracy.
1. Turn on the projector and display an image.
2. Slide the lens shift dial lock as shown to release the lock.
99  
						

							3. Turn the vertical and horizontal lens shift dials on the projector to adjust the position of the projected
image as necessary.
Note: You can move the image within the ranges shown below. You cannot move the image to both
the horizontal and vertical maximum values.
PowerLite Pro G6070W/G6270W/G6470WU/G6570WU/G6770WU/G6970WU
100