Epson Projector PowerLite Pro G6570WU User Manual

Parent topic:
Attaching and Removing a Lens
Attaching and Removing the Cable Cover You can attach the cable cover that came with your projector to hide the attached cables from view.
1. Bundle the cables together using a band or other fastener (not provided).
2. Place the cable cover on the projector as shown, guiding the cables through the notch on the base ofthe cable cover.
51   

3. Tighten both cable cover screws.
To remove the cover, loosen both screws and pull the cover off of the projector.
Parent topic:
Setting Up the Projector
Attaching and Removing the Cable Clips You can install the cable clips that came with your projector to provide additional support to the power
and HDMI cables.
Note:The PowerLite Pro G6070W/G6170/G6270W/G6470WU/G6570WU/G6770WU come with one
cable clip.
1. Connect the power and HDMI cables to the projector.
52  

2. Insert the end of the cable clip anchors into the cable clip slots near the power inlet and
HDMIport.
1 Cable clip slot
2 Cable clip anchor
3 Cable clip
3. Place the open cable clips around the power and HDMI cables, but dont lock them into place.
4. Slide each cable clip onto the anchors and lock the clips onto the power and HDMI connectors as shown.
To remove the cable clips, open the clips and disconnect the cables. Then pinch the sides of each cable
clip anchor and carefully pull them out of the...

Caution:
Use only the type of batteries specified in this manual. Do not install batteries of different types,
or mix new and old batteries.
1. Remove the battery cover.
2. Insert the batteries with the +and –ends facing as shown.
54   

3. Replace the battery cover and press it down until it clicks into place.
Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat
or flame. Keep batteries out of the reach of children; they are choking hazards and are very
dangerous if swallowed.
Parent topic: Setting Up the Projector
55  

Using the Projector on a Network
Follow the instructions in these sections to set up your projector for use on a network.
Wired Network Projection
Wireless Network Projection
Registering a Digital Certificate on the Projector
Setting Up Projector Network E-Mail Alerts
Setting Up Monitoring Using SNMP
Selecting Other Network Settings
Controlling a Networked Projector Using a Web Browser
Crestron RoomView Support
Wired Network Projection You can send images to your projector through a wired network...

Note:
If your projector is connected via a LAN cable to a network that includes a wireless access point,
you can connect to the projector wirelessly through the access point using the EasyMP Network
Projection software (PowerLite Pro G6070W/G6170/G6270W/G6470WU/G6570WU/G6770WU).
Connecting to a Wired Network
Selecting Wired Network Settings
Parent topic: Using the Projector on a Network
Connecting to a Wired Network To connect the projector to a wired local area network (LAN), use a 100Base-TX or...

3. Select the
Networkmenu and press Enter.
4. Select Network Configuration and pressEnter.
5. Select the Basicmenu and press Enter.
58 

6. Select the following basic options as necessary:
•Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the
projector over the network.
• Web Remote Password (PowerLite Pro
G6070W/G6170/G6270W/G6470WU/G6570WU/G6770WU) or Web Control Password
(PowerLite Pro G6870/G6970WU) lets you enter a password up to 8 alphanumeric characters
long for accessing the projector over the web. (Default user name is EPSONWEB; default
password is admin.)
• Projector Keyword (PowerLite Pro...

• If you must set addresses manually, turn off
DHCPand enter the projectors IP Address,Subnet
Mask, and Gateway Address as needed.
Note: To highlight the numbers you want from the displayed keyboard, press the arrow buttons on
the remote control. To select a highlighted number, press Enter.
9. To prevent display of the IP address on the standby screen, turn off IP Address Display.
10. When you finish selecting settings, select Setup completeand follow the on-screen instructions to
save your settings and...