Epson Projector PowerLite Pro G6470WU User Manual

							PowerLite Pro G6070W/G6170/G6270W/G6470WU/G6570WU/G6770WU
5. Enter up to two IP addresses to receive SNMP notifications, using 0 to 255 for each address field. Note: To enter the IP address using the numeric keys on the remote control, press and hold the
Num button. Do not use these addresses: 127.x.x.x or 224.0.0.0 through 255.255.255.255 (where x
is a number from 0 to 255).
6. Enter a community name (PowerLite G6070W/G6170/G6270W/G6470WU/G6570WU/G6770WU). You can enter up to 32 single-byte alphanumeric characters.
7. When you finish selecting settings, select CompleteorSetup complete and follow the on-screen
instructions to save your settings and exit the menus.
Parent topic: Using the Projector on a Network
Selecting Other Network Settings You can select other network setting options.
1. Press theMenubutton.
2. Select the Networkmenu and press Enter.
3. Select Network Configuration and pressEnter.
81 
						

							4. Do one of the following:
• Select the Othersmenu and press Enter.
PowerLite Pro G6870/G6970WU
• Select the Administrator Setting menu and pressEnter.
PowerLite Pro G6070W/G6170/G6270W/G6470WU/G6570WU/G6770WU
82 
						

							5. If available, select the
Priority Gatewaysetting for your network.
6. If your network environment uses an AMX controller, turn on the AMX Device Discoverysetting to
allow the projector to be detected.
7. If your network environment uses a Crestron RoomView controller, turn on the Crestron RoomView
setting to allow the projector to be detected.
Note: Enabling Crestron RoomView disables the Epson Message Broadcast feature in the EasyMP
Monitor software.
8. If your network environment uses a Control4 or Control4 SDDP controller, turn on the Control4
SDDP setting to allow the projector to be detected.
9. If you want this projector to receive broadcasted messages over the network, turn on the Message
Broadcasting setting. Administrators can broadcast messages over the network using the Message
Broadcasting plug-in for EasyMP Monitor (Windows only).
10. When you finish selecting settings, select CompleteorSetup complete and follow the on-screen
instructions to save your settings and exit the menus.
Parent topic: Using the Projector on a Network
Controlling a Networked Projector Using a Web Browser Once you have connected your projector to your network, you can select projector settings and control
projection using a compatible web browser. This lets you access the projector remotely.
Note:The web setup and control features support Microsoft Internet Explorer 8.0 or later, and Safari on
networks that do not use a proxy server for connection. You cannot select all of the projector menu
settings or control all projector functions using a web browser.
Note: If you set Standby Mode to Communication On, you can use a web browser to select settings
and control projection even if the projector is in standby mode.
1. Make sure the projector is turned on.
2. Start your web browser on a computer or device connected to the network.
3. Type the projectors IP address into the browsers address box and press the computers Enterkey.
Note: You may need to log in before you see the Web Control screen. If you see a log in window,
enter your user name and password. (The default user name is EPSONWEBand the default
password is admin.)
83 
						

							You see the Web Control screen.
Note:
If you connect from a web browser on a smartphone or tablet, a screen with two options is
displayed. Select remoteto display the Web Remote page, or select configto display the Web
Control page.
4. To select projector menu settings, select the name of the menu and follow the on-screen instructions.
5. To control projection remotely, select the Web Remoteoption.
You see a screen like this:
84  
						

							1 Power on button control
2 Input source selection controls (some buttons may not be available depending on your
available projector ports)
3 Freeze button control
4 A/V Mute button control
5 Page Up andPage Down button controls
6 Closed caption control
7 Volume button controls
8 Source search control
9 Standby button control
6. Select the icon corresponding to the projector function you want to control.
Parent topic: Using the Projector on a Network
Related references
Projector Setup Settings - Extended Menu
Crestron RoomView Support If you are using the Crestron RoomView network monitoring and control system, you can set up your
projector for use on the system. Crestron RoomView lets you control and monitor your projector using a
web browser.
Note:You cannot use the Epson Web Control feature or the Message Broadcasting plug-in for EasyMP
Monitor when you use Crestron RoomView.
For additional information on Crestron RoomView, contact Crestron.
Setting Up Crestron RoomView Support
Controlling a Networked Projector Using Crestron RoomView
Parent topic: Using the Projector on a Network
Setting Up Crestron RoomView Support To set up your projector for monitoring and control using a Crestron RoomView system, make sure your
computer and projector are connected to the network.
85 
						

							Note:
If you want to use the Crestron RoomView system when the projector is turned off, you need to
adjust the Standby Mode settings in the Extended menu.
1. Press the Menubutton.
2. Select the Networkmenu and press Enter.
3. Select Network Configuration and pressEnter.
4. Select the Othersmenu (PowerLite Pro G6870/G6970WU) or the Administrator Settingmenu
(PowerLite Pro G6070W/G6170/G6270W/G6470WU/G6570WU/G6770WU) and press Enter.
PowerLite Pro G6870/G6970WU
86 
						

							PowerLite Pro G6070W/G6170/G6270W/G6470WU/G6570WU/G6770WU
5. Set the Crestron RoomView setting toOnto allow the projector to be detected.
Note: Enabling Crestron RoomView disables the Epson Message Broadcasting feature in the
EasyMP Monitor software.
6. When you finish selecting settings, select Completeand follow the on-screen instructions to save
your settings and exit the menus.
7. Turn off the projector, then turn it on again to enable the setting.
Parent topic: Crestron RoomView Support
Controlling a Networked Projector Using Crestron RoomView Once you have set up your projector to use Crestron RoomView, you can control and monitor projection
using a compatible web browser.
1. Start your web browser on a computer connected to the network.
2. Type the projectors IP address into the browsers address box and press the computers Enterkey.
87 
						

							You see this screen:
3. Select the input source that you want to control in the Sources List box. You can scroll through available sources using the up and down arrows in the box.
4. To control projection remotely, click the on-screen buttons that correspond to the projectors remote control buttons. You can scroll through button options at the bottom of the screen.
Note: These on-screen buttons do not directly correspond to the projectors remote control buttons:
• OK acts as the Enterbutton
• Menu displays the projectors menu
5. To view information about the projector, click the Infotab.
6. To change projector, Crestron, and password settings, click the Toolstab, select settings on the
displayed screen, and click Send.
7. When you finish selecting settings, click Exitto exit the program.
Parent topic: Crestron RoomView Support
88  
						

							Using Basic Projector Features
Follow the instructions in these sections to use your projectors basic features.
Turning On the Projector
Turning Off the Projector
Selecting the Language for the Projector Menus
Resizing the Image with the Zoom Ring
Focusing the Image Using the Focus Ring
Setting the Lens Type
Setting the Screen Type
Adjusting the Image Position Using Screen Position
Adjusting the Image Position Using Lens Shift
Displaying a Test Pattern
Adjusting the Image Height
Image Shape
Remote Control Operation
Selecting an Image Source
Projection Modes
Image Aspect Ratio
Color Mode
Controlling the Volume with the Volume Buttons
Setting the Date and Time
Turning On the Projector Turn on the computer or video equipment you want to use before you turn on the projector so it can
display the image source.
Note:If theStartup Source Search setting in the Extended menu is enabled, the projector
automatically detects the input signal when you turn it on.
89 
						

							1. Connect the power cord to the projectors power inlet.
2. Plug the power cord into an electrical outlet.
The projectors power light turns orange. This indicates that the projector is receiving power, but is
not yet turned on (it is in standby mode).
Note: With Direct Power On turned on, the projector turns on as soon as you plug it in.
3. Press the power button on the projector or the Onbutton on the remote control to turn on the
projector.
The projector beeps and the power light flashes green as the projector warms up. After about 30
seconds, the power light stops flashing and turns green.
Warning: Never look into the projector lens when the lamp is on. This can damage your eyes and is
especially dangerous for children and pets.
If you do not see a projected image right away, try the following:
• Turn on the connected computer or video device.
• Insert a DVD or other video media, and press the play button (if necessary).
• Press the Source Search button on the projector or the Searchbutton on the remote control to detect
the video source.
90