Home > Epson > Projector > Epson Projector PowerLite Pro G6470WU User Manual

Epson Projector PowerLite Pro G6470WU User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Epson Projector PowerLite Pro G6470WU User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1734 Epson manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							1. To prevent unauthorized use of the projector, select
    Power On Protection, pressEnter, selectOn,
    press Enter again, and press Esc.
    2. To prevent changes to the Users Logo screen or related display settings, select Users Logo
    Protection, press Enter, selectOn, pressEnteragain, and press Esc.
    3. To prevent changes to network settings, select Network Protection, pressEnter, selectOn, press
    Enter again, and press Esc.
    4. To prevent changes to the projectors time or schedule settings, select Time/Schedule Protection,
    press Enter, select On, pressEnteragain, and press Esc.
    Note: Be sure to keep the remote control in a safe place; if you lose it, you will not be able to enter the
    password required to use the projector.
    Parent topic: Password Security Types
    Entering a Password to Use the Projector If a password is set up and a Power On Protectionpassword is enabled, you see a prompt to enter a
    password whenever you turn on the projector.
    You must enter the correct password to use the projector.
    141 
    						
    							1. Press and hold down the
    Numbutton on the remote control while you enter the password using the
    numeric buttons.
    Note: The default password is 0000.
    The password screen closes.
    2. If the password is incorrect, the following may happen: • You see a wrong password message and a prompt to try again. Enter the correct password toproceed.
    • If you enter an incorrect password several times in succession, the projector displays a request code and a message to contact Epson Support. Do not attempt to enter the password again.
    When you contact Epson Support, provide the displayed request code and proof of ownership for
    assistance in unlocking the projector.
    Parent topic: Password Security Types
    Saving a Users Logo Image to Display You can transfer an image to the projector and then display it whenever the projector turns on. You can
    also display the image when the projector is not receiving an input signal or when you temporarily stop
    projection (using the A/V Mute feature). This transferred image is called the Users Logo screen.
    The image you select as the Users Logo can be a photo, graphic, or company logo, which is useful in
    identifying the projectors owner to help deter theft. You can prevent changes to the Users Logo by
    setting up password protection for it.
    1. Display the image you want to project as the Users Logo.
    142  
    						
    							2. Press the
    Menubutton, select the Extendedmenu, and press Enter.
    3. Select the Users Logosetting and press Enter.
    You see a prompt asking if you want to use the displayed image as a users logo.
    4. Select Yesand press Enter.
    You see a selection box overlaying your image.
    5. Use the arrow buttons on the remote control to surround the image area you want to use as the Users Logo and press Enter.
    You see a prompt asking if you want to select this image area.
    6. Select Yesand press Enter. (If you want to change the selected area, select No, pressEnter, and
    repeat the last step.)
    143 
    						
    							You see the Users Logo zoom factor menu.
    7. Select a zoom percentage and press Enter.
    You see a prompt asking if you want to save the image as the Users Logo.
    8. Select Yesand press Enter.
    You see a completion message.
    9. Press Escto exit the message screen.
    10. Select the Extendedmenu and press Enter.
    11. Select Displayand press Enter.
    12. Select when you want to display the Users Logo screen: • To display it whenever there is no input signal, select Display Backgroundand set it toLogo.
    • To display it whenever you turn the projector on, select Startup Screenand set it toOn.
    • To display it whenever you press the A/V Mutebutton, select A/V Muteand set it to Logo.
    To prevent anyone from changing the Users Logo settings without first entering a password, set a
    password and enable Users Logo security.
    Parent topic: Password Security Types
    Locking the Projectors Buttons You can lock the buttons on the projectors control panel to prevent anyone from using the projector. You
    can lock all the buttons or all the buttons except the power button.
    1. Press theMenubutton.
    144 
    						
    							2. Select the
    Settingsmenu and press Enter.
    3. Select the Control Panel Lock setting and pressEnter.
    4. Select one of these lock types and press Enter:
    • To lock all of the projectors buttons, select Full Lock.
    • To lock all buttons except the power button, select Partial Lock.
    You see a confirmation prompt.
    5. Select Yesand press Enter.
    Unlocking the Projectors Buttons
    Parent topic: Projector Security Features
    Unlocking the Projectors Buttons If the projectors buttons have been locked, hold the Enterbutton on the projectors control panel for
    seven seconds to unlock them.
    Parent topic: Locking the Projectors Buttons
    Installing a Security Cable You can install two types of security cables on the projector to deter theft.
    145 
    						
    							• Use the security slot on the projector to attach a Kensington lock. See your local computer or
    electronics dealer for purchase information.
    • Use the security cable attachment point on the projector to attach a wire cable and secure it to a room fixture or heavy furniture.
    Note: Do not pass drop-prevention cables through the security cable attachment point when mounting
    the projector on a wall or ceiling.
    Parent topic: Projector Security Features
    Related references
    Projector Parts - Rear
    Projecting Two Images Simultaneously You can use the split screen feature to simultaneously project two images from different image sources
    next to each other. You can control the split screen feature using the remote control or the projector
    menus.
    Note:While you use the split screen feature, other projector features may not be available and some
    settings may be automatically applied to both images.
    Note: You cannot project from the same input source onto both sides (left and right) of the screen. You
    also cannot use split screen with certain input source combinations.
    146  
    						
    							1. Press the
    Splitbutton on the remote control.
    The currently selected input source moves to the left side of the screen.
    2. Press the Menubutton.
    You see this screen:
    3. To select an input source for the other image, select the Sourcesetting, press Enter, select the
    input source, select Execute, and press Enter. (You can also change image sources, if necessary.)
    4. To switch the images, select the Swap Screenssetting and press Enter.
    5. To change the image sizes, select the Screen Sizesetting, press Enter, select a sizing option,
    press Enter, and press Menuto exit.
    Note: Depending on the video input signals, the images may not appear at the same size even if you
    choose the Equalsetting.
    6. To choose the audio you want to hear, select the Audio Sourcesetting, pressEnter, select an
    audio option, press Enter, and pressMenuto exit.
    Note: Select Autoto hear audio from the largest screen or the left screen.
    147  
    						
    							7. To exit the split screen feature, press the
    SplitorEsc button.
    Parent topic: Adjusting Projector Features
    Using Multiple Projectors You can combine the projected images from two or more projectors to create one large image. The
    following two options are available:
    • Project different images from each projector and create one seamless image
    • Project the same image from each projector and use the Scale feature to create one seamless image
    148   
    						
    							Follow the instructions in these sections to setup and project from multiple projectors.
    Projector Identification System for Multiple Projector Control
    Adjusting the Position of the Projected Image From Multiple Projectors
    Scaling an Image
    Adjusting the Lamps Brightness
    Blending the Image Edges
    Adjusting the Black Level
    Matching the Image Colors
    Parent topic:
    Adjusting Projector Features
    Projector Identification System for Multiple Projector Control You can operate multiple projectors using one remote control for more elaborate presentations. To do
    this, you assign an identification number to each projector and to the remote control. Then you can
    operate all the projectors at once or individually.
    You can also match the colors displayed by any projectors you plan to use near each other.
    Caution:Leave at least 20 inches (50 cm) of space between the projectors to prevent them from
    overheating.
    Setting the Projector ID
    Setting the Remote Control ID
    Parent topic: Using Multiple Projectors
    Setting the Projector ID If you want to control multiple projectors from a remote control, give each projector a unique ID.
    1. Press theMenubutton.
    2. Select the Extendedmenu and press Enter.
    3. Select the Multi-Projection menu and pressEnter.
    149 
    						
    							4. Select
    Projector ID and pressEnter.
    5. Use the arrow buttons on the remote control to select the identification number you want to use for the projector. Then press Enter.
    Repeat these steps for all the other projectors you want to operate from one remote control.
    Parent topic: Projector Identification System for Multiple Projector Control
    Setting the Remote Control ID The remote controls ID is set to 0by default so it can operate any compatible projector. If you want to set
    the remote control to operate only a particular projector, you need to set the remote controls ID to match
    the projectors ID.
    1. Turn on the projector you want the remote control to operate with exclusively.
    2. Set the remote control IDswitch to On.
    150  
    						
    All Epson manuals Comments (0)

    Related Manuals for Epson Projector PowerLite Pro G6470WU User Manual