Epson Projector PowerLite Pro Cinema LS9600e User Manual

							7. Select the
Wired LANmenu and press Enter.
8. Select IP Settings and pressEnter.
9. Select your IP Settings as necessary: • If your network assigns addresses automatically, turn on the DHCPsetting.
41 
						

							• If you must set addresses manually, turn off
DHCPand enter the projectors IP Address,Subnet
Mask, and Gateway Address as needed. When manually entering IP Settings, you cannot use
restricted IP addresses.
Note: To highlight the numbers you want from the displayed keyboard, press the arrow buttons on
the remote control. To select a highlighted number, press Enter.
10. To prevent display of the IP address on the standby screen, turn off IP Address Display.
11. When you finish selecting settings, select Completeand follow the on-screen instructions to save
your settings and exit the menus.
Restricted IP Addresses
Parent topic: Wired Network Monitoring and Control
Restricted IP Addresses When manually entering IP Settings, you cannot use these ranges of IP addresses:
Setting Restricted IP addresses
IP Address 0.0.0.0
127.x.x.x
192.0.2.x
224.0.0.0 to 255.255.255.255
Subnet Mask 0.0.0.0
255.255.255.255
Gateway Address 0.0.0.0
197.x.x.x
224.0.0.0 to 255.255.255.255
Parent topic: Selecting Wired Network Settings
Setting Up Projector Network E-Mail Alerts You can set up the projector to send you an e-mail alert over the network if there is a problem with the
projector.
1. Press theMenubutton.
42 
						

							2. Select the
Networkmenu and press Enter.
3. Select Network Configuration and pressEnter.
4. Select the Mailmenu and press Enter.
5. Turn on Mail Notification.
6. Enter the IP address for the SMTP Serveroption.
Note: Do not use these addresses: 127.x.x.x or 224.0.0.0 through 255.255.255.255 (where x is a
number from 0 to 255).
7. Select a number for the SMTP server Port Number, from 1 to 65535 (default is 25).
8. Choose an Addressfield, enter the e-mail address, and select the alerts you want to receive there.
Repeat for up to three addresses.
Note: Your e-mail address can be up to 64 alphanumeric characters long. You can only enter 32
characters via the projector menu. To enter more than 32 characters, use the web configuration
page to enter the e-mail address.
9. When you finish selecting settings, select Completeand follow the on-screen instructions to save
your settings and exit the menus.
Note: If a critical problem causes a projector to shut down, you may not receive an e-mail alert.
43 
						

							Network Projector E-mail Alert Messages
Parent topic:
Using the Projector on a Network
Network Projector E-mail Alert Messages When a problem occurs with a networked projector, and you selected to receive e-mail alerts, you
receive an e-mail containing the following information:
•Epson Projector on the subject line
• The name of the projector experiencing a problem
• The IP address of the affected projector
• Detailed information about the problem
Note: If a critical problem causes a projector to shut down, you may not receive an e-mail alert.
Parent topic: Setting Up Projector Network E-Mail Alerts
Setting Up Network Monitoring Network administrators can install monitoring software on network computers so they can monitor
projectors. If your network uses this software, you can set up the projector for monitoring.
1. Press theMenubutton.
2. Select the Networkmenu and press Enter.
3. Select Network Configuration and pressEnter.
44 
						

							4. Select the
Othersmenu and press Enter.
5. If your network environment uses an AMX controller, turn on the AMX Device Discoverysetting to
allow the projector to be detected.
6. If your network environment uses a Control4 or Control4 SDDP controller, turn on the Control4
SDDP setting to allow the projector to be detected (PowerLite Pro Cinema LS10000).
7. If you are connecting to a network using Bonjour, turn on the Bonjoursetting.
8. When you finish selecting settings, select Completeand follow the on-screen instructions to save
your settings and exit the menus.
Parent topic: Using the Projector on a Network
Controlling a Networked Projector Using a Web Browser Once you have connected your projector to your network, you can select projector settings and control
projection using a compatible web browser. This lets you access the projector remotely.
Note:The web setup and control features support Microsoft Internet Explorer 8, 9, or 10, and Safari on
networks that do not use a proxy server for connection. You cannot select all of the projector menu
settings or control all projector functions using a web browser.
Note: If you set Standby Mode to Communication On, you can use a web browser to select settings
and control projection even if the projector is in standby mode.
45 
						

							1. Make sure the projector is turned on.
2. Start your web browser on a computer or device connected to the network.
3. Type the projectors IP address into the browsers address box and press the computers
Enterkey.
Note: If you connect from a web browser on a smartphone or tablet, a screen with two options is
displayed. Select remoteto display the Web Remote page, or select configto display the Web
Control page.
You see the Web Control screen.
Note: You may need to log in before you see the Web Control screen. If you see a log in window,
enter your user name and password. (The default user name is EPSONWEBand the default
password is admin.)
4. To select projector menu settings, select the name of the menu and follow the on-screen instructions.
5. To control projection remotely, select the Web Remoteoption.
46 
						

							You see a screen like this:
1 Turns the projector on
2 Turns the projector off
3 Selects HDMI1,HDMI2,WiHD(PowerLite Pro Cinema LS9600e), 3RCA(component), Video,
and PCport sources
4 Blank button control
5 Switches between 2D and 3D projection
6 Loads a saved lens position
6. Select the icon corresponding to the projector function you want to control.
Parent topic: Using the Projector on a Network
47  
						

							Using Basic Projector Features
Follow the instructions in these sections to use your projectors basic features.
Turning On the Projector
Turning Off the Projector
Viewing 3D Images
Selecting the Language for the Projector Menus
Adjusting the Image Height
Image Shape
Resizing the Image with the Zoom Feature
Focusing the Image with the Lens Button
Adjusting the Color Convergence (Panel Alignment)
Remote Control Operation
Selecting an Image Source
Projection Modes
Image Aspect Ratio
Color Mode
Changing the Super-resolution Setting
Changing the Super-resolution/4K Enhancement Setting
Using Picture in Picture
Turning On the Projector Turn on the computer or video equipment you want to use before you turn on the projector so it can
display the image source.
48 
						

							1. Connect the power cord to the projectors power inlet.
2. Plug the power cord into an electrical outlet.
Note: WithDirect Power On turned on, the projector turns on as soon as you plug it in.
3. Press the power button on the projector or the Onbutton on the remote control to turn on the
projector.
The shutter opens and the Status light flashes blue as the projector warms up. Once the projector is
warmed up, the Status light stops flashing and turns blue.
Warning: Never look into the projector lens when the laser is on. This can damage your eyes and is
especially dangerous for children.
If you do not see a projected image right away, try the following:
• Turn on the connected computer or video device.
• Insert a DVD or other video media and press the play button, if necessary.
• Press the Sourcebutton on the projector to detect the video source, or press a source button on the
remote control.
Parent topic: Using Basic Projector Features
Related references
Projector Feature Settings - Settings Menu
49  
						

							Turning Off the Projector
Before turning off the projector, shut down any computer connected to it so you can see the computer
display during shutdown.
Note:Turn off this product when not in use to prolong the life of the projector. Laser life will vary
depending upon mode selected, environmental conditions, and usage. Brightness decreases over time.
Note: When using the Blank feature, the laser is still on. To turn off the laser, turn off the projector.
1. Press the power button on the projector or the Standbybutton on the remote control.
The projector displays a shutdown confirmation screen.
2. Press the power button on the projector or the Standbybutton on the remote control again. (To
leave it on, press any other button.)
The shutter closes, the laser turns off, and the Status light turns off.
Caution: Do not turn the projector on immediately after turning it off. Turning the projector on and off
frequently may shorten the life of the laser.
50