Epson Projector PowerLite Pro Cinema LS9600e User Manual

							6. Vacuum the front of the air filter (the side with the tabs) to remove any remaining dust.
Note: If dust is difficult to remove or the air filter is damaged, replace the air filter.
7. Place the air filter back in the projector as shown.
121   
						

							8. Close the air filter cover and press until it clicks into place.
9. Replace the cable cover if necessary.
Parent topic:
Air Filter and Vent Maintenance
Replacing the Air Filter You need to replace the air filter in the following situations:
• After cleaning the air filter, you see a message telling you to clean or replace it
• The air filter is torn or damaged
You can replace the air filter while the projector is mounted to the ceiling or placed on a table.
1. Turn off the projector and unplug the power cord.
2. Remove the cable cover, if necessary.
122  
						

							3. Press and hold the tab on the air filter cover, and pull to open the cover.
123  
						

							4. Pull the air filter out of the projector.
Note: Air filters contain polypropylene. Dispose of used air filters according to local regulations.
5. Place the new air filter in the projector as shown.
124   
						

							6. Close the air filter cover and press until it clicks into place.
7. Replace the cable cover, if necessary.
Parent topic:
Air Filter and Vent Maintenance
Related references
Optional Equipment and Replacement Parts
Replacing the Remote Control Batteries The remote control uses two AA manganese or alkaline batteries. Replace the batteries as soon as they
run out.
Caution:Use only the type of batteries specified in this manual. Do not install batteries of different types,
or mix new and old batteries.
125  
						

							1. Remove the battery cover as shown.
2. Remove the old batteries.
Warning: If the battery fluid has leaked, wipe it away with a soft cloth and avoid getting the fluid on
your hands. If it gets on your hands, wash them immediately to avoid injury.
3. Insert the batteries with the +and –ends facing as shown.
126   
						

							4. Replace the battery cover and press it down until it clicks into place.
Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat
or flame. Keep batteries out of the reach of children; they are choking hazards and are very
dangerous if swallowed.
Parent topic: Projector Maintenance
Transporting the Projector The projector contains precision parts, some of which are glass. Follow these guidelines to transport,
ship, or store the projector safely:
• Remove any equipment connected to the projector.
• When transporting the projector a long distance or as checked luggage, pack it in a firm box withcushioning around it and mark the box Fragile.
• When shipping the projector for repairs, place it in its original packing materials, if possible, or use equivalent materials with cushioning around the projector. Mark the box Fragile.
Note: Epson shall not be liable for any damages incurred during transportation.
Parent topic: Maintaining and Transporting the Projector
127  
						

							Solving Problems
Check the solutions in these sections if you have any problems using the projector.
Projection Problem Tips
Projector Light Status
Solving Image Problems
Solving Projector or Remote Control Operation Problems
Solving Network Problems
Where to Get Help
Projection Problem Tips If the projector is not working properly, try turning it off and unplugging it. Then plug it back in and turn it
on.
If this does not solve the problem, check the following:
• The lights on the projector may indicate what the problem is.
• The solutions in this manual can help you solve many problems.
If none of these solutions help, you can contact Epson for technical support.
Parent topic:Solving Problems
Projector Light Status The lights on the projector indicate the projector status and let you know when a problem occurs. Check
the status and color of the lights and look for a solution in the table here.
128 
						

							1
Temp light
2 Laser light
3 Status light
4 Power light
Power light Status light Laser light Temp light Status and solution
Blue BlueOff Off Normal operation or standby (with
Communication On)
129  
						

							Power light Status light Laser light Temp light Status and solution
Blue
Flashing blue Off Off Warming up; wait for an image to
appear
or
Shutting down; when the Status light
stops flashing, you can unplug the
projector
Off OffOff Off Standby or sleep mode
Blue OffOff Off Standby (withCommunication On)
or WirelessHD standby (PowerLite
Pro Cinema LS9600e)
Flashing blue Varies Varies Flashing Projector is too hot orange• Make sure that the vents and air
filter are not clogged with dust or
obstructed by nearby objects
• Clean or replace the air filter
• Make sure the environmental temperature is not too hot
Off Flashing blue Off Orange Projector has overheated and turned
off; leave it turned off until it cools
down, then do the following:
• Make sure that the vents and airfilter are not clogged with dust or
obstructed by nearby objects
• Clean or replace the air filter
• If the problem persists, unplug the projector and contact Epson for
help
130