Epson Projector PowerLite Pro Cinema LS10000 User Manual

2. Insert the end of the cable clip anchor into the cable clip slot near the
HDMIport.
3. Place the open cable clip around the HDMI cable, but dont lock it into place.
4. Slide the cable clip onto the anchor and lock the clip onto the HDMI connector.
To remove the cable clip, open the clip and disconnect the HDMI cable. Then pinch the sides of the
cable clip anchor and carefully pull it out of the cable clip slot.
Parent topic: Connecting to Video Sources
Connecting to an MHL-Compatible Device If you...

Parent topic:
Connecting to Video Sources
Related topics
Using WirelessHD
Connecting to a Component Video Source If your video source has component video ports, you can connect it to the projector using an optional
component video cable. Depending on your component ports, you may need to use an adapter cable
along with a component video cable.
1. Connect the component connectors to your video sources color-coded component video outputports, usually labeled Y,Pb, ProrY, Cb, Cr. If you are using an...

2. Connect the other end to the projectors
Videoport.
Parent topic: Connecting to Video Sources
Connecting to Computer Sources Follow the instructions in these sections to connect a computer to the projector.
Connecting to a Computer for VGA Video
Connecting to a Computer for HDMI Video
Parent topic:Projector Connections
Connecting to a Computer for VGA Video You can connect the projector to your computer using a VGA computer cable.
Note:To connect a Mac that includes only a Mini DisplayPort, Thunderbolt...

4. Tighten the screws on the VGA connector.
Parent topic:
Connecting to Computer Sources
Connecting to a Computer for HDMI Video If your computer has an HDMI port, you can connect it to the projector using an optional HDMI cable.
Note:To connect a Mac that includes only a Mini DisplayPort, Thunderbolt port, or Mini-DVI port for
video output, you need to obtain an adapter that allows you to connect to the projectors HDMIport.
1. Connect the HDMI cable to your computers HDMI output port.
2. Connect the...

connection provides the best image quality, if available). You can also connect speakers to any video
source that has its own speaker connections.
1 Video source
2 Surround sound speakers
3 Receiver
4 Video cable
Parent topic: Projector Connections
Connecting to a Trigger Out Port You can connect your projector to external devices such as motorized screens that support a trigger
signal. When active, a 12V signal is sent to the connected device while the projector is powered on.
1. Connect a 3.5 mm stereo...

2. Connect the other end to one of the projectors
Trigger Outports.
3. Activate the trigger port in the projectors Settingsmenu.
Parent topic: Projector Connections
Installing Batteries in the Remote Control The remote control uses the two AA batteries that came with the projector.
Caution:Use only the type of batteries specified in this manual. Do not install batteries of different types,
or mix new and old batteries.
1. Remove the battery cover.
36   

2. Insert the batteries with the
+and –ends facing as shown.
3. Replace the battery cover and press it down until it clicks into place.
Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat
or flame. Keep batteries out of the reach of children; they are choking hazards and are very
dangerous if swallowed.
Parent topic: Setting Up the Projector
Related tasks
Replacing the Remote Control Batteries
37   

Using the Projector on a Network
Follow the instructions in these sections to set up your projector for use on a network.
Wired Network Monitoring and Control
Setting Up Projector Network E-Mail Alerts
Setting Up Network Monitoring
Controlling a Networked Projector Using a Web Browser
Wired Network Monitoring and Control You can monitor, configure, and control your projector through a wired network. You can also send email
alerts from the projector when a problem occurs. To do this, you connect the...

Selecting Wired Network Settings
Before you can project from computers on your network, you must select the network settings for the
projector using its menu system.
Note:Make sure you already connected the projector to your wired network using the LANport.
1. Turn on the projector.
2. Press the Menubutton.
3. Select the Networkmenu and press Enter.
4. Select Network Configuration and pressEnter.
39 

5. Select the
Basicmenu and press Enter.
6. Select the following basic options as necessary: •Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the
projector over the network.
• PJLink Password lets you enter a password up to 32 alphanumeric characters long for using the
PJLink protocol for projector control.
• Web Control Password lets you enter a password up to 8 alphanumeric characters long for
accessing the projector over the web. (Default user name is EPSONWEB;...