Epson Projector L1100U User Manual

							71
Setting Up Projector Network E-Mail Alerts
You can set up the projector to send you an e-mail alert over the network if there is a problem with the
projector.
1. Press theMenubutton.
2. Select the Networkmenu and press Enter.
3. Select Network Configuration and pressEnter.
4. Select the Notificationsmenu and press Enter.
5. Turn on Mail Notification.
6. Enter the IP address for the SMTP Serversetting.
Note: To enter the IP address using the numeric keys on the remote control, press and hold the
Num button. Do not use these addresses: 127.x.x.x or 224.0.0.0 through 255.255.255.255 (where x
is a number from 0 to 255).
7. Select a number for the SMTP server Port Numbersetting, from 1 to 65535 (default is 25).
8. Choose an Addressfield, enter the e-mail address, and select the alerts you want to receive there.
Repeat for up to three addresses. Your e-mail address can be up to 32 alphanumeric characters
long. 
						

							72
9. When you finish selecting settings, select
Completeand follow the on-screen instructions to save
your settings and exit the menus.
Note: If a critical problem causes a projector to shut down, you may not receive an e-mail alert.
Network Projector E-mail Alert Messages
Parent topic: Using the Projector on a Network
Network Projector E-mail Alert Messages When a problem occurs with a networked projector, and you selected to receive e-mail alerts, you
receive an e-mail containing the following information:
•Epson Projector on the subject line
• The name of the projector experiencing a problem
• The IP address of the affected projector
• Detailed information about the problem
Note: If a critical problem causes a projector to shut down, you may not receive an e-mail alert.
Parent topic: Setting Up Projector Network E-Mail Alerts
Selecting Other Network Settings You can select optional network settings on the Others menu.
1. Press theMenubutton.
2. Select the Networkmenu and press Enter.
3. Select Network Configuration and pressEnter. 
						

							73
4. Select the
Othersmenu and press Enter.
5. If available, select the Priority Gatewaysetting for your network.
6. If your network environment uses an AMX controller, turn on the AMX Device Discoverysetting to
allow the projector to be detected.
7. If your network environment uses a Crestron RoomView controller, turn on the Crestron RoomView
setting to allow the projector to be detected.
Note: Enabling Crestron RoomView disables the Epson Message Broadcast feature in the EasyMP
Monitor software.
8. If your network environment uses a Control4 or Control4 SDDP controller, turn on the Control4
SDDP setting to allow the projector to be detected.
9. If you want to control the projector using Art-Net (an Ethernet communication protocol based on TCP/IP), turn on the Art-Netsetting (Pro L1405U/L1500U/L1505U).
10. If you want this projector to receive broadcasted messages over the network, turn on the Message
Broadcasting setting. Administrators can broadcast messages over the network using the Message
Broadcasting plug-in for EasyMP Monitor (Windows only).
11. When you finish selecting settings, select Completeand follow the on-screen instructions to save
your settings and exit the menus.
Parent topic: Using the Projector on a Network 
						

							74
Controlling a Networked Projector Using a Web Browser
Once you have connected your projector to your network, you can select projector settings and control
projection using a compatible web browser. This lets you access the projector remotely.
Note:The web setup and control features support Microsoft Internet Explorer 9.0 or later, and Safari on
networks that do not use a proxy server for connection. You cannot select all of the projector menu
settings or control all projector functions using a web browser.
Note: If you set Standby Mode to Communication On, you can use a web browser to select settings
and control projection even if the projector is in standby mode.
1. Make sure the projector is turned on.
2. Start your web browser on a computer or device connected to the network.
3. Type the projectors IP address into the browsers address box and press the computers Enterkey.
Note: You may need to log in before you see the Web Control screen. If you see a log in window,
enter your user name and password. (The default user name is EPSONWEBand the default
password is admin.)
You see the Web Control screen.
1 Select Basic Control to control the projector remotely
2 Select OSD Control Pad to change the projectors menu settings  
						

							75
3 Select
Test Pattern to display a test pattern
4 Select Advancedto open the advanced menu screen
5 Select Status Information to view the projectors status
6 Select Lens Control to adjust the lens (focus, zoom, and lens shift)
4. Select the option corresponding to the projector function you want to control.
Web Control Options
Parent topic: Using the Projector on a Network
Related references
Projector Setup Settings - Extended Menu
Web Control Options Basic Control
Note:If the Remote Password is set to On, you need to enter your user name and password. (The
default username is EPSONREMOTEand the default password is guest).
1 Returns to the Home screen
2 Turns on the projector  
						

							76
3 Input source selection controls
4
A/V Mute button control
5 Volume button controls
6 Searches for sources
7 Turns off the projector
OSD Control Pad
1 Returns to the Home screen
2 Displays the projectors setting menus
3 Use your finger or mouse to navigate the menus
4 Returns settings to their default values
5 Returns to the previous menu
6 Displays help topics
Note: You cannot change some settings using Epson Web Control.  
						

							77
Lens Control
Focus/Distortion screen
1 Returns to the Home screen
2 Focus adjustment slider
3 Focus adjustment buttons
4 Distortion adjustment slider (not available for ELPLU02)
5 Distortion adjustment buttons (not available for ELPLU02)
6 Displays the Focus/Distortion screen
7 Displays the Zoom screen
8 Displays the Lens Shift screen
9 Displays the Test Pattern screen
10 Displays the Memory screen
Zoom screen  
						

							78
Note:
Zoom is not available for ELPLX01 and ELPLR04.
1 Zoom adjustment slider
2 Zoom adjustment buttons
Lens Shift screen
1 The current image position is displayed as a blue square and the new image position is displayed as a red square   
						

							79
2 Displays the vertical image position; select to change the value
3 Moves the image position up, down, left, or right
4 Moves the lens to the home position
5 Displays the horizontal image position; select to change the value
Test Pattern screen
1 Displays available test patterns; select to project a test pattern
2 Turns off test pattern display  
						

							80
Memory screen
1 Overwrites your current settings with saved settings
2 Saves your current settings to memory
3 Displays a list of saved memories
4 Erases a saved memory
5 Renames a saved memory
Status Information